Shahin Khoddam
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shahin Khoddam has a total of 74 co-authors. Here are the top co-authors by number of shared publications:
P.D. Hodgson
12 shared publications- Thaneshan Sapanathan
Curtin Corrosion Centre, Curtin University Perth Western Australia Australia
8 shared publications - Amir Hossein Shamdani
Monash University
7 shared publications - Saden H. Zahiri
CSIRO Manufacturing and Materials Technology
6 shared publications A. Farhoumand
5 shared publicationsA. Zarei-Hanzaki
5 shared publications
Latest Publications
- 17 February 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (6)
Enhancing Axisymmetric Compression Testing: Modeling and Addressing Flow Curve Errors
Axisymmetric compression testing (ACT) stands as a pivotal experimental technique, widely embraced for its capacity to identify the plastic flow attributes inherent to diverse materials. However, the accuracy of the flow curve obtained from ACT can be significantly affected by errors introduced by the inevitable barrelling and foldover, which can lead to erroneous interpretation of deformation phenomena. The existing analytical and numerical solutions for estimating effective stress in ACT are first reviewed. A new closed‐form solution that is insensitive to friction and foldover is then presented. The solution is based on a multilayer model of the sample geometry, which considers the instantaneous barrelling of the sample. The multilayer solution is validated against a reference numerical solution and shows good agreement, even after a significant foldover. The results indicate that the proposed framework can significantly improve the accuracy of material flow characterization. This can be of significant value in the fields of material processing, manufacturing, and materials science.
- 17 February 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (6)
Enhancing Axisymmetric Compression Testing: Modeling and Addressing Flow Curve Errors
Axisymmetric compression testing (ACT) stands as a pivotal experimental technique, widely embraced for its capacity to identify the plastic flow attributes inherent to diverse materials. However, the accuracy of the flow curve obtained from ACT can be significantly affected by errors introduced by the inevitable barrelling and foldover, which can lead to erroneous interpretation of deformation phenomena. The existing analytical and numerical solutions for estimating effective stress in ACT are first reviewed. A new closed‐form solution that is insensitive to friction and foldover is then presented. The solution is based on a multilayer model of the sample geometry, which considers the instantaneous barrelling of the sample. The multilayer solution is validated against a reference numerical solution and shows good agreement, even after a significant foldover. The results indicate that the proposed framework can significantly improve the accuracy of material flow characterization. This can be of significant value in the fields of material processing, manufacturing, and materials science.
- Open Access
- 22 December 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (12)
A comprehensive experimental and numerical study of foldover onset and growth during the barrelling compression test
Foldover is a common, yet complex, transient boundary condition in several ‘metal forming processes’ including the barrelling compression test (BCT). The onset of foldover during BCT is comparable to that of necking in the tensile test. However, its role in flow curve identification has been ignored in the current literature. Methods to detect and measure its onset and growth during the processes are also not available. We propose three methods to identify the onset of foldover and measure its progress with deformation. These are conducted together with case studies of BCT to have a fundamental understanding of the onset and growth of foldover in the test and more general cases. Experimental and numerical methods are developed to accomplish this based on (1) direct measurement using tracing points, (2) energy-based and (3) geometry-based indirect measurements. These outline the required supplementary data and allow proper detection of the onset. In the first method, the migration of tracing points from the free surface to the platen-sample interface, simulated numerically, is monitored and measured visually. The second method employs the load-stroke data to calculate the total power input to the deforming system. In the third method, a criterion has been derived to detect the onset of foldover by monitoring the geometry of the sample profile during the test and comparing it to a reference quadratic profile. The observations and outputs of each method are compared and discussed.
- 22 December 2022
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 14 (12)
Open AccessA comprehensive experimental and numerical study of foldover onset and growth during the barrelling compression test
Foldover is a common, yet complex, transient boundary condition in several ‘metal forming processes’ including the barrelling compression test (BCT). The onset of foldover during BCT is comparable to that of necking in the tensile test. However, its role in flow curve identification has been ignored in the current literature. Methods to detect and measure its onset and growth during the processes are also not available. We propose three methods to identify the onset of foldover and measure its progress with deformation. These are conducted together with case studies of BCT to have a fundamental understanding of the onset and growth of foldover in the test and more general cases. Experimental and numerical methods are developed to accomplish this based on (1) direct measurement using tracing points, (2) energy-based and (3) geometry-based indirect measurements. These outline the required supplementary data and allow proper detection of the onset. In the first method, the migration of tracing points from the free surface to the platen-sample interface, simulated numerically, is monitored and measured visually. The second method employs the load-stroke data to calculate the total power input to the deforming system. In the third method, a criterion has been derived to detect the onset of foldover by monitoring the geometry of the sample profile during the test and comparing it to a reference quadratic profile. The observations and outputs of each method are compared and discussed.
- Open Access
- 8 April 2022
- Published by Springer Nature in Experimental Mechanics
- Vol. 62 (6) , 929-942
Critical Evaluation of Identified Flow Curves Using Homogeneous and Heterogeneous Solutions for Compression Test
Background: The cylindrical profile model (CPM) is commonly used to convert the load–displacement measurement from the axis-symmetric compression test (ACT) to the flow curve. The model ignores the barrelling of the sample which results in serious flow curve distortion and underestimation of the effective stress and strain. To minimize these, a new solution of ACT with heterogeneous deformation is proposed in this work as an alternative to CPM. Method: Representative point is introduced in this new approach for better utilization of the new solution. Some key attributes of a typical flow curve are also considered to explore the sensitivity of the identified flow curve to the heterogeneous deformation. Sample flow curves are identified based on the new solution and compared with that of CPM. Results: It was found that CPM underestimates the maximum effective stress, strain and strain rate. Significant deviations were found between the reference flow curves and those of CPM. The model is unable to appropriately account for the rate-dependent behaviour of material and work hardening variations in the samples. Therefore, given its non-realistic homogeneous effective strain and strain rate in the sample, the CPM based flow curves are questionable. The new ACT solution provided more reliable flow curves than those of the CPM. Conclusions: Considering the heterogeneous deformation at the centre of the sample, the new ACT solution provided flow curves that for strains bellow 0.4 closely resemble the reference curves obtained from the finite element model. Thus, the new ACT solution reduces the serious limitations of CPM and provides less error in the study of the hot deformation phenomena (e.g. recovery and recrystallization). Further recommendations were also given to limit the deviations in the identified flow curve.
- 8 April 2022
- Published by Springer Nature in Experimental Mechanics
- Vol. 62 (6) , 929-942
Open AccessCritical Evaluation of Identified Flow Curves Using Homogeneous and Heterogeneous Solutions for Compression Test
Background: The cylindrical profile model (CPM) is commonly used to convert the load–displacement measurement from the axis-symmetric compression test (ACT) to the flow curve. The model ignores the barrelling of the sample which results in serious flow curve distortion and underestimation of the effective stress and strain. To minimize these, a new solution of ACT with heterogeneous deformation is proposed in this work as an alternative to CPM. Method: Representative point is introduced in this new approach for better utilization of the new solution. Some key attributes of a typical flow curve are also considered to explore the sensitivity of the identified flow curve to the heterogeneous deformation. Sample flow curves are identified based on the new solution and compared with that of CPM. Results: It was found that CPM underestimates the maximum effective stress, strain and strain rate. Significant deviations were found between the reference flow curves and those of CPM. The model is unable to appropriately account for the rate-dependent behaviour of material and work hardening variations in the samples. Therefore, given its non-realistic homogeneous effective strain and strain rate in the sample, the CPM based flow curves are questionable. The new ACT solution provided more reliable flow curves than those of the CPM. Conclusions: Considering the heterogeneous deformation at the centre of the sample, the new ACT solution provided flow curves that for strains bellow 0.4 closely resemble the reference curves obtained from the finite element model. Thus, the new ACT solution reduces the serious limitations of CPM and provides less error in the study of the hot deformation phenomena (e.g. recovery and recrystallization). Further recommendations were also given to limit the deviations in the identified flow curve.
- Open Access
- 19 November 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (11)
State of the art methods to post-process mechanical test data to characterize the hot deformation behavior of metals
Materials engineering and science rely heavily on the indirect measurement of plastic stress and strain by post-processing of mechanical test data, including tension, torsion, and compression test. There is no consensus among researchers regarding the best test or the post-processing theory nor do adequate standards exist on the characterization methods. The tests are typically performed as customized tests, discrepancies exist in the flow curves obtained by different methods and the chosen mechanical test. More critically, the curves are dominantly treated (perceived) as a set of measured data rather than calculated values. The plasticity-based calculated flow curves and their gradients are, in turn, the basis for several second-tier indirect measurements, such as stacking fault energy and recrystallization. Such measurements are quite prone to errors due to oversimplified post-processing of the tests’ data and can only be experimentally verified in a qualitative or in an average fashion. Therefore, their findings are highly restricted by the limitations of each test, data type and post-processing method, and should be used carefully. This review examines some of the most commonly used data conversion methods and some recent developments in the field followed by recommendations. It will highlight the need to develop test rigs that can provide new data types and to provide advanced post-processing techniques for the indirect measurement.
- 19 November 2021
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 13 (11)
Open AccessState of the art methods to post-process mechanical test data to characterize the hot deformation behavior of metals
Materials engineering and science rely heavily on the indirect measurement of plastic stress and strain by post-processing of mechanical test data, including tension, torsion, and compression test. There is no consensus among researchers regarding the best test or the post-processing theory nor do adequate standards exist on the characterization methods. The tests are typically performed as customized tests, discrepancies exist in the flow curves obtained by different methods and the chosen mechanical test. More critically, the curves are dominantly treated (perceived) as a set of measured data rather than calculated values. The plasticity-based calculated flow curves and their gradients are, in turn, the basis for several second-tier indirect measurements, such as stacking fault energy and recrystallization. Such measurements are quite prone to errors due to oversimplified post-processing of the tests’ data and can only be experimentally verified in a qualitative or in an average fashion. Therefore, their findings are highly restricted by the limitations of each test, data type and post-processing method, and should be used carefully. This review examines some of the most commonly used data conversion methods and some recent developments in the field followed by recommendations. It will highlight the need to develop test rigs that can provide new data types and to provide advanced post-processing techniques for the indirect measurement.
- Open Access
- 1 January 2021
- Published by AGH University Press in Computer Methods in Material Science
- Vol. 21 (3) , 157-162
Conversion of compression test data into flow curve, accounting for barrelling
Current solutions to convert the axis-symmetric compression test (ACT) data to flow data ignore the barrelling deformation in the sample. This work presents a solution for the test which accounts for the sample’s barrelling by discretising it into a finite number of layers of different radii. The solution assumes a constant and sliding friction at the anvil-sample interface. The sample’s flow behaviour is identified by combining a recent kinematic solution of the test, Prandtl–Reuss–Mises’s equations and a slab-analysis of the layers. It also involves an averaging of the effective plastic stresses developed in the individual layers. The solution is verified for a special case of no-barrelling which matches the currently used solution.
- 1 January 2021
- Published by AGH University Press in Computer Methods in Material Science
- Vol. 21 (3) , 157-162
Open AccessConversion of compression test data into flow curve, accounting for barrelling
Current solutions to convert the axis-symmetric compression test (ACT) data to flow data ignore the barrelling deformation in the sample. This work presents a solution for the test which accounts for the sample’s barrelling by discretising it into a finite number of layers of different radii. The solution assumes a constant and sliding friction at the anvil-sample interface. The sample’s flow behaviour is identified by combining a recent kinematic solution of the test, Prandtl–Reuss–Mises’s equations and a slab-analysis of the layers. It also involves an averaging of the effective plastic stresses developed in the individual layers. The solution is verified for a special case of no-barrelling which matches the currently used solution.
- 1 October 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 161-162
A power-based approach to assess the barrelling test's weak solution
- 1 October 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 161-162
A power-based approach to assess the barrelling test's weak solution
- 3 December 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (6) , 4754-4765
Deformation under combined compression and shear: a new kinematic solution
- 3 December 2018
- Published by Springer Nature in Journal of Materials Science
- Vol. 54 (6) , 4754-4765
Deformation under combined compression and shear: a new kinematic solution
- 1 July 2018
- Published by Elsevier in Mechanics of Materials
- Vol. 122, 1-8
Advancing mechanics of Barrelling Compression Test
- 1 July 2018
- Published by Elsevier in Mechanics of Materials
- Vol. 122, 1-8
Advancing mechanics of Barrelling Compression Test
- 23 May 2018
- Published by Wiley in Advanced Engineering Materials
- Vol. 20 (9)
Latest Developments in Modeling and Characterization of Joining Metal Based Hybrid Materials
Advanced materials consist of several materials systems that exhibit complementary properties for multi‐purpose applications. Joining of dissimilar materials is a critical and challenging advanced manufacturing technique to develop novel hybrid materials with properties fully transferred. The “bonding strength” of a joint is crucial for its integrity and performance. The bonding strength is affected by a range of parameters that can be better understood, controlled, and optimized via both experimental and analytical approaches. In this paper, the authors review the theoretical and experimental studies of the interface inside several metal based composites. The scope includes interface bonding's critical parameters, characterization techniques of joining processes, potential applications, and their future perspectives. The review is significant to develop advanced manufacturing techniques for heterogeneous materials and to design innovative heterogeneous systems for various medical, electrical, electronics, industrial, and other daily life applications that involve the broad range of “joining” processes.
- 23 May 2018
- Published by Wiley in Advanced Engineering Materials
- Vol. 20 (9)
Latest Developments in Modeling and Characterization of Joining Metal Based Hybrid Materials
Advanced materials consist of several materials systems that exhibit complementary properties for multi‐purpose applications. Joining of dissimilar materials is a critical and challenging advanced manufacturing technique to develop novel hybrid materials with properties fully transferred. The “bonding strength” of a joint is crucial for its integrity and performance. The bonding strength is affected by a range of parameters that can be better understood, controlled, and optimized via both experimental and analytical approaches. In this paper, the authors review the theoretical and experimental studies of the interface inside several metal based composites. The scope includes interface bonding's critical parameters, characterization techniques of joining processes, potential applications, and their future perspectives. The review is significant to develop advanced manufacturing techniques for heterogeneous materials and to design innovative heterogeneous systems for various medical, electrical, electronics, industrial, and other daily life applications that involve the broad range of “joining” processes.
- 14 September 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 48 (11) , 5759
Erratum to: Environment-Assisted Cracking of Twinning Induced Plasticity (TWIP) Steel: Role of pH and Twinning
- 14 September 2017
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 48 (11) , 5759
Erratum to: Environment-Assisted Cracking of Twinning Induced Plasticity (TWIP) Steel: Role of pH and Twinning