AMAbdul Moudood

Abdul Moudood

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Abdul Moudood has a total of 7 co-authors. Here are the top co-authors by number of shared publications:

  • Andreas Öchsner

    Faculty of Mechanical Engineering Esslingen University of Applied Sciences Kanalstrasse 33 73728 Esslingen Germany

    3 shared publications
  • Anisur Rahman

    Griffith School of Engineering and Built Environment Gold Coast Campus, Griffith University Gold Coast Australia

    3 shared publications
  • Gaston Francucci

    Research Institute of Material Science and Technology (INTEMA-CONICET), National University of Mar del Plata, Mar del Plata, Argentina

    3 shared publications
  • Mainul Islam

    School of Mechanical and Electrical Engineering, Faculty of Health, Engineering and Sciences University of Southern Queensland West Street Toowoomba QLD 4350 Australia

    2 shared publications
  • Mainul Islam

    School of Science, Engineering and Digital Technologies and Centre for Future Materials, University of Southern Queensland, Toowoomba, QLD 4350, Australia

    1 shared publication
  • Mohammad Yeakub Ali

    Mechanical Engineering Programme Area

    1 shared publication

Latest Publications

  • Mechanical properties of flax fiber‐reinforced composites at different relative humidities: Experimental, geometric, and displacement potential function approaches

    by Abdul Moudood, Anisur Rahman, Nayeem Md Lutful Huq, Andreas Öchsner, Mainul Islam, Gaston Francucci

    Due to the good mechanical properties, flax fiber‐reinforced epoxy composites are being widely used as a green alternative to glass fiber composites. However, plant fibers absorb moisture from the environment, being in a higher moisture uptake as the relative humidity (RH) increases. This absorbed moisture deteriorates the mechanical properties of the composites. In this study, geometric and displacement potential function (DPF) approaches are used to predict the mechanical properties of flax fiber‐reinforced epoxy composites under environmental conditions, in particular, different RH values. The tensile properties that were measured experimentally strongly agreed with the analytical findings. Almost similar results were found for the tensile strain those were measured experimentally and the one predicted by the geometric function. However, the predicted strain values were 38% and 42% less than the experimental ones for 0% and 95% RH conditioned composites, respectively, when DPF was used. Good conformity between the experimental, analytical, and DPF formulation for predicting mechanical properties ensures the practical applicability of this study. The formulations established in this work could, therefore, be utilized to analytically solve laminated composites under specific boundary conditions in structural applications.


  • Open Access

    Effects of Different Relative Humidities on Flax Fibers prior to Manufacturing Their Composites Based on the Shear Response

    by Abdul Moudood, Anisur Rahman, Andreas Öchsner, Mainul Islam, Mohammad Yeakub Ali, Gaston Francucci

    The moisture absorption behavior of flax fiber‐reinforced epoxy composites is deliberated to be a serious issue. This property restricts their usage as outdoor engineering structures. Therefore, this study provides an investigation of moisture in flax fibers on the performance of the flax/epoxy composite materials based on their shear responses. The ±45° aligned flax fibers exposed to different relative humidities (RH) and the vacuum infusion process was used to manufacture the composite specimens. The optimum shear strength (40.25 ± 0.75 MPa) was found for the composites manufactured with 35% RH‐conditioned flax fibers, but the shear modulus was reduced consistently with increasing RH values. Although shear strength was increased because of fiber swelling with increased moisture absorption rate until 35% RH environments with good microstructures, nonetheless, strength and modulus both started to decrease after this range. A very poor microstructure has been affirmed by the SEM images of the composite samples conditioned at 90% RH environments.


  • Flax fiber and its composites: An overview of water and moisture absorption impact on their performance

    by Abdul Moudood, Anisur Rahman, Andreas Öchsner, Mainul Islam, Gaston Francucci

    Contemporary researchers have specified that natural flax fiber is comparable with synthetic fibers due to its unique physical and mechanical characteristics which have been recognized for decades. Flax fiber-reinforced composites have the potential for wide usage in sport and maritime industries, and as automotive accessories. In addition, this composite is in the development stages for future applications in the aeronautical industry. However, designing the flax composite parts is a challenging task due to the great variability in fiber properties. This is caused by many factors, including the plant origin and growth conditions, plant age, location in the stem, fibers extraction method, and the fact that there is often a non-uniform cross section of the fibers. Furthermore, the water and moisture absorption tendency of the flax fibers and their composites and the consequent detrimental effects on their mechanical performance are also major drawbacks. Fibers may soften and swell with absorbed water molecules, which could affect the performance of this bio-composite. Flax fibers’ moisture absorption propensity may lead to a deterioration of the fiber–matrix interface, weakening the interfacial strength and ultimately degrading the quality of the composite. This review represents a brief summary of the main findings of research into flax fiber reinforced composites, focusing on the challenges of its water and moisture absorption behavior on their performance.