Suraj Kumar Saw
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Suraj Kumar Saw has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Alak Majumder
National Institute of Technology Arunachal Pradesh
8 shared publications Vijay Nath
Birla Institute of Technology
8 shared publicationsMadhusudan Maiti
Department of Electronics and Communication Engineering, National Institute of Technology Arunachal Pradesh, Yupia, 791112, India
6 shared publications- Abhishek Pandey
Birla Institute of Technology, Mesra
3 shared publications Abir Jyoti Mondal
2 shared publicationsMonalisa Das
Department of ECE, NIT Arunachal Pradesh, Arunachal Pradesh, India
2 shared publications
Latest Publications
- 5 July 2020
- Published by Bentham Science Publishers Ltd. in Recent Advances in Electrical & Electronic Engineering (Formerly Recent Patents on Electrical & Electronic Engineering)
- Vol. 13 (4) , 516-530
PVT Aware Design of a Dead-zone Free High Speed Phase Frequency Detector in 90nm CMOS
Background & Introduction: With the advent of technology, though the literature highlights many designs of Phase Frequency Detector (PFD), there remains some challenges like area overhead, switching noise near frequency lock point and fast, accurate response to mitigate dead zone and output errors. Methods: In this article, we have unearthed a low power, high speed and dead zone free PFD, which eliminates the switching noise near that lock-in node. This simple design uses lesser number of transistors to obtain smaller estimated layout area of 0.748mm2 and low power of 496.12μW, when operated at 10 GHz frequency at a power supply of 1.8V in 90nm CMOS technology. Results: The simulation reads a phase noise and output noise of -113.142dBc/Hz and -180.712dB at 1MHz offset. The circuit not only runs at a frequency as high as 40GHz, but also compatible to be operated at a power supply of as small as 0.9V. Conclusion: Process Variation analysis performed proves the robustness of the proposed circuit at all process corners. Also, the design gets validated at lower process nodes like 28nm UMC.
- 5 July 2020
- Published by Bentham Science Publishers Ltd. in Recent Advances in Electrical & Electronic Engineering (Formerly Recent Patents on Electrical & Electronic Engineering)
- Vol. 13 (4) , 516-530
PVT Aware Design of a Dead-zone Free High Speed Phase Frequency Detector in 90nm CMOS
Background & Introduction: With the advent of technology, though the literature highlights many designs of Phase Frequency Detector (PFD), there remains some challenges like area overhead, switching noise near frequency lock point and fast, accurate response to mitigate dead zone and output errors. Methods: In this article, we have unearthed a low power, high speed and dead zone free PFD, which eliminates the switching noise near that lock-in node. This simple design uses lesser number of transistors to obtain smaller estimated layout area of 0.748mm2 and low power of 496.12μW, when operated at 10 GHz frequency at a power supply of 1.8V in 90nm CMOS technology. Results: The simulation reads a phase noise and output noise of -113.142dBc/Hz and -180.712dB at 1MHz offset. The circuit not only runs at a frequency as high as 40GHz, but also compatible to be operated at a power supply of as small as 0.9V. Conclusion: Process Variation analysis performed proves the robustness of the proposed circuit at all process corners. Also, the design gets validated at lower process nodes like 28nm UMC.
- Open Access
- 1 June 2020
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 11 (2) , 265-272
A hybrid design approach of PVT tolerant, power efficient ring VCO
- 1 June 2020
- Published by Elsevier in Ain Shams Engineering Journal
- Vol. 11 (2) , 265-272
Open AccessA hybrid design approach of PVT tolerant, power efficient ring VCO
- 7 November 2019
- Published by Springer Nature in Microsystem Technologies
- Vol. 26 (5) , 1489-1497
Passive element free variation aware decision circuit for 40 Gb/s CDR application
- 7 November 2019
- Published by Springer Nature in Microsystem Technologies
- Vol. 26 (5) , 1489-1497
Passive element free variation aware decision circuit for 40 Gb/s CDR application
- 31 May 2019
- Published by Springer Nature in Microsystem Technologies
- Vol. 26 (2) , 563-572
A design approach of higher oscillation VCO made of CS amplifier with varying active load
- 31 May 2019
- Published by Springer Nature in Microsystem Technologies
- Vol. 26 (2) , 563-572
A design approach of higher oscillation VCO made of CS amplifier with varying active load
- 8 May 2019
- Published by Springer Nature in Microsystem Technologies
- Vol. 25 (12) , 4615-4624
A power efficient PFD-CP architecture for high speed clock and data recovery application
- 8 May 2019
- Published by Springer Nature in Microsystem Technologies
- Vol. 25 (12) , 4615-4624
A power efficient PFD-CP architecture for high speed clock and data recovery application
- 31 December 2018
- Published by Springer Nature
- p. 421-429
Design of Differential Amplifier Using Current Mirror Load in 90 nm CMOS Technology
- 31 December 2018
- Published by Springer Nature
- p. 421-429
Design of Differential Amplifier Using Current Mirror Load in 90 nm CMOS Technology
- 14 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (3) , 1231-1244
Variation Aware Design of 50-Gbit/s, 5.027-fJ/bit Serializer Using Latency Combined Mux-Dual Latch for Inter-Chip Communication
The conventional MOS current mode logic (MCML)-based multiplexer needed for serializer application has various limitations, such as low voltage-swing, substantial power consumption, and large area overhead. In the circuit arrangement of a serializer using the MCML-based mux-tree concept, the output of one mux at any stage is used to feed another mux at the next stage through some latch circuits, which are basically used for timing synchronization giving away penalty in terms of delay and area. The increase in number of stages of the Serializer may lead to further reduction in output swing (if common mode is not properly set), thereby causing signal integrity issues and finally loss of data. To address the same, a latency combined current mode multiplexer incorporating pMOS-based dual cross-coupled latch circuit is unearthed in this paper to further outline an area and energy efficient high-speed serializer capable of maintaining uniform peak-to-peak swing and signal quality at differential outputs. The simulations of new serializer are performed for 90-nm CMOS in the Cadence Virtuoso platform, where the average power and delay are found to be 471.6 μW and 93.9 ps, respectively, to provide a power delay product of 43.8 fJ only at a power supply of 1 V. An improved output swing of 904 mV is also noticed along with a data rate of 50 Gb/s and a BER of <;10 -12 . The entire design is proved to be a robust one after simulating it through Monte Carlo at five different process corners and also validated at lower process nodes such as 28-nm UMC.
- 14 November 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (3) , 1231-1244
Variation Aware Design of 50-Gbit/s, 5.027-fJ/bit Serializer Using Latency Combined Mux-Dual Latch for Inter-Chip Communication
The conventional MOS current mode logic (MCML)-based multiplexer needed for serializer application has various limitations, such as low voltage-swing, substantial power consumption, and large area overhead. In the circuit arrangement of a serializer using the MCML-based mux-tree concept, the output of one mux at any stage is used to feed another mux at the next stage through some latch circuits, which are basically used for timing synchronization giving away penalty in terms of delay and area. The increase in number of stages of the Serializer may lead to further reduction in output swing (if common mode is not properly set), thereby causing signal integrity issues and finally loss of data. To address the same, a latency combined current mode multiplexer incorporating pMOS-based dual cross-coupled latch circuit is unearthed in this paper to further outline an area and energy efficient high-speed serializer capable of maintaining uniform peak-to-peak swing and signal quality at differential outputs. The simulations of new serializer are performed for 90-nm CMOS in the Cadence Virtuoso platform, where the average power and delay are found to be 471.6 μW and 93.9 ps, respectively, to provide a power delay product of 43.8 fJ only at a power supply of 1 V. An improved output swing of 904 mV is also noticed along with a data rate of 50 Gb/s and a BER of <;10 -12 . The entire design is proved to be a robust one after simulating it through Monte Carlo at five different process corners and also validated at lower process nodes such as 28-nm UMC.
- 23 August 2018
- Published by Springer Nature in Microsystem Technologies
- Vol. 27 (2) , 555-568
An energy efficient PVT aware novel CML-TG based Mux-Latch circuit Serializes high rate data
- 23 August 2018
- Published by Springer Nature in Microsystem Technologies
- Vol. 27 (2) , 555-568
An energy efficient PVT aware novel CML-TG based Mux-Latch circuit Serializes high rate data
- 17 July 2018
- Published by Springer Nature in Microsystem Technologies
- Vol. 27 (2) , 479-491
A power efficient charge pump circuit configuration for fast locking PLL application
- 17 July 2018
- Published by Springer Nature in Microsystem Technologies
- Vol. 27 (2) , 479-491
A power efficient charge pump circuit configuration for fast locking PLL application
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 229-233
Design of high frequency D flip flop circuit for phase detector application
A low power, high frequency positive edge D flip flop circuit is implemented. Its operating frequency is 5GHz with a supply voltage of 1.8 V produces a output at a positive edge triggered signal. It consists of 16 transistor which compel low power of 10.42 μW with a phase noise of -147dBc/Hz and output noise -154.77dB at offset frequency 1 MHz, Circuits is also tested at different corner frequency and has minimal area of 88.571μmm 2 simulation of results is done by cadence tools in 90nm CMOS process The proposed D flip flop has outplayed the prior research in terms of performance metrics.
- 1 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 229-233
Design of high frequency D flip flop circuit for phase detector application
A low power, high frequency positive edge D flip flop circuit is implemented. Its operating frequency is 5GHz with a supply voltage of 1.8 V produces a output at a positive edge triggered signal. It consists of 16 transistor which compel low power of 10.42 μW with a phase noise of -147dBc/Hz and output noise -154.77dB at offset frequency 1 MHz, Circuits is also tested at different corner frequency and has minimal area of 88.571μmm 2 simulation of results is done by cadence tools in 90nm CMOS process The proposed D flip flop has outplayed the prior research in terms of performance metrics.