Iman Zohourkari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Iman Zohourkari has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Mehdi Zohoor
Faculty of Mechanical Engineering, K. N. Toosi University of Technology, Tehran, Iran
4 shared publications- Massimiliano Annoni
Department of Mechanical Engineering, Politecnico di Milano, Milan 20156, Italy
3 shared publications - Mehdi Zohoor
Faculty of Mechanical Engineering, K. N. Toosi University of Technology, Tehran, Iran
2 shared publications Ali Merdji
Department of Mechanical Engineering, Faculty of Science and Technology, University of Mascara, Mascara, Algeria
1 shared publication- Constance Linda Gnanasagaran
School of Engineering and the Environment, Kingston University, London, UK
1 shared publication - Foad Faraji
School of Computing, Engineering and Digital Technologies, Teesside University, Middlesbrough TS1 3BX, UK
1 shared publication
Latest Publications
- 21 July 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
- Vol. 237 (8) , 1008-1016
Mechanical influence of tissue scaffolding design with different geometries using finite element study
The mechanical properties of tissue scaffolds are essential in providing stability for tissue repair and growth. Thus, the ability of scaffolds to withstand specific loads is crucial for scaffold design. Most research on scaffold pores focuses on grids with pore size and gradient structure, and many research models are based on scaffolding with vertically arranged holes. However, little attention is paid to the influence of the distribution of holes on the mechanical properties of the scaffold. To address this gap, this research investigates the effect of pore distribution on the mechanical properties of tissue scaffolds. The study involves four types of scaffold designs with regular and staggered pore arrangements and porosity ranging from 30% to 80%. Finite element analysis (FEA) was used to compare the mechanical properties of different scaffold designs, with von-Mises stress distribution maps generated for each scaffold. The results show that scaffolds with regular vertical holes exhibit a more uniform stress distribution and better mechanical performance than those with irregular holes. In contrast, the scaffold with a staggered arrangement of holes had a higher probability of stress concentration. The study emphasized the importance of balancing porosity and strength in scaffold design.
- 21 July 2023
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
- Vol. 237 (8) , 1008-1016
Mechanical influence of tissue scaffolding design with different geometries using finite element study
The mechanical properties of tissue scaffolds are essential in providing stability for tissue repair and growth. Thus, the ability of scaffolds to withstand specific loads is crucial for scaffold design. Most research on scaffold pores focuses on grids with pore size and gradient structure, and many research models are based on scaffolding with vertically arranged holes. However, little attention is paid to the influence of the distribution of holes on the mechanical properties of the scaffold. To address this gap, this research investigates the effect of pore distribution on the mechanical properties of tissue scaffolds. The study involves four types of scaffold designs with regular and staggered pore arrangements and porosity ranging from 30% to 80%. Finite element analysis (FEA) was used to compare the mechanical properties of different scaffold designs, with von-Mises stress distribution maps generated for each scaffold. The results show that scaffolds with regular vertical holes exhibit a more uniform stress distribution and better mechanical performance than those with irregular holes. In contrast, the scaffold with a staggered arrangement of holes had a higher probability of stress concentration. The study emphasized the importance of balancing porosity and strength in scaffold design.
- Open Access
- 20 April 2023
- Published by Springer Nature in Research Square
Numerical study of the effect of orthogonal cutting parameters on the shear plane angle in 4340 steel
In an orthogonal cutting process, the shear plane has a significant force resulting from chip removal action, since in the chip removal process, most of the force applied to the workpiece is used to change the shape of the material in the form of heat and it is dissipated by the chip, tool and the workpiece. It can be seen that the shear zone takes the highest temperature during the chip removal process. Therefore, increasing or decreasing the area of the shear plane and its angle has a direct effect on reducing the temperature and force resulting from chip removal and accordingly, improving the cutting conditions. In this research, the effect of machining parameters including cutting velocity, depth of cut, rake angle, and tool radius on temperature, force, and angle of cutting plane in AISI 4340 alloy is studied. The two-dimensional finite element model of orthogonal cutting is simulated as a couple of dynamic-thermal loads. The results obtained from the simulation in DEFORM software show that the depth of cut has the greatest effect on the changes in the angle of the shear plane in such a way that increasing the depth of cut decreases the angle of the shear plane and vice versa, also, the radius of the tool has the least effect on the changes in the angle. The results obtained from the numerical simulation are in good agreement with metal-cutting theories.
- 20 April 2023
- Published by Springer Nature in Research Square
Open AccessNumerical study of the effect of orthogonal cutting parameters on the shear plane angle in 4340 steel
In an orthogonal cutting process, the shear plane has a significant force resulting from chip removal action, since in the chip removal process, most of the force applied to the workpiece is used to change the shape of the material in the form of heat and it is dissipated by the chip, tool and the workpiece. It can be seen that the shear zone takes the highest temperature during the chip removal process. Therefore, increasing or decreasing the area of the shear plane and its angle has a direct effect on reducing the temperature and force resulting from chip removal and accordingly, improving the cutting conditions. In this research, the effect of machining parameters including cutting velocity, depth of cut, rake angle, and tool radius on temperature, force, and angle of cutting plane in AISI 4340 alloy is studied. The two-dimensional finite element model of orthogonal cutting is simulated as a couple of dynamic-thermal loads. The results obtained from the simulation in DEFORM software show that the depth of cut has the greatest effect on the changes in the angle of the shear plane in such a way that increasing the depth of cut decreases the angle of the shear plane and vice versa, also, the radius of the tool has the least effect on the changes in the angle. The results obtained from the numerical simulation are in good agreement with metal-cutting theories.
- Open Access
- 27 January 2023
- Published by Al-Kindi Center for Research and Development in Journal of Mechanical, Civil and Industrial Engineering
- Vol. 4 (1) , 50-56
A Feasible Study on the Application of Cyclic Annealing Treatment for Functionality Improvement of 3D Printed PLA Parts
In the 3D printing of polymeric parts, the annealing cycle is a post-process method that allows different polymeric materials to enhance their mechanical and thermal properties and also eliminate their residual stresses. However, annealing has some drawbacks, such as producing induced shrinkage to the treated parts. In this study, a new technique named “cyclic annealing” is proposed to reduce shrinkage due to annealing treatment. By subsequent increasing and reduction of the temperature over and below the glass transition temperature instead of suddenly increasing the temperature to the target annealing temperature, a significant reduction of shrinkage was observed for the printed PLA parts. Various cylindrical shape samples with different infill densities (30%, 50%, 70%, and 100%) were examined at 70°C, 90°C, and 110°C annealing temperatures. Considerable reduction of shrinkage by up to 50% and improvement of the material strength were observed, which confirms the applicability of the proposed cyclic annealing method as an alternative to traditional polymer annealing for 3D printed materials.
- 27 January 2023
- Published by Al-Kindi Center for Research and Development in Journal of Mechanical, Civil and Industrial Engineering
- Vol. 4 (1) , 50-56
Open AccessA Feasible Study on the Application of Cyclic Annealing Treatment for Functionality Improvement of 3D Printed PLA Parts
In the 3D printing of polymeric parts, the annealing cycle is a post-process method that allows different polymeric materials to enhance their mechanical and thermal properties and also eliminate their residual stresses. However, annealing has some drawbacks, such as producing induced shrinkage to the treated parts. In this study, a new technique named “cyclic annealing” is proposed to reduce shrinkage due to annealing treatment. By subsequent increasing and reduction of the temperature over and below the glass transition temperature instead of suddenly increasing the temperature to the target annealing temperature, a significant reduction of shrinkage was observed for the printed PLA parts. Various cylindrical shape samples with different infill densities (30%, 50%, 70%, and 100%) were examined at 70°C, 90°C, and 110°C annealing temperatures. Considerable reduction of shrinkage by up to 50% and improvement of the material strength were observed, which confirms the applicability of the proposed cyclic annealing method as an alternative to traditional polymer annealing for 3D printed materials.
- 25 September 2014
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 229 (12) , 2125-2133
Influence of machining parameters on part geometrical error in abrasive waterjet offset-mode turning
Geometrical error in abrasive waterjet turned parts is an important challenge toward the commercialization of abrasive waterjet turning process. A systematic study has not been done yet to investigate the effects of process parameters on geometrical error in abrasive waterjet offset-mode turning. In this article, a comprehensive study has been performed to investigate the influence of several machining parameters on the geometrical error (part diameter percent error) in turning AA2011-T4 aluminum alloy round bars. Water pressure, cutting head traverse speed, workpiece rotational speed, abrasive mass flow rate and depth of cut were considered as the main machining parameters in a five-level statistical experimental design. Based on central composite rotatable design, a total of 52 experiments were carried out. The main effects of the parameters and interactions among them were analyzed based on the analysis of variance technique, and the response contours for the part geometrical error were obtained using a quadratic regression model (i.e. response surface methodology). The model predictions were found to be in good agreement with experimental data. Furthermore, among the significant parameters, water pressure, depth of cut and traverse speed are the most influential parameters, with percent contribution of almost 25% each. Abrasive mass flow rate is the least influential parameter with a percent contribution of 4%.
- 25 September 2014
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture
- Vol. 229 (12) , 2125-2133
Influence of machining parameters on part geometrical error in abrasive waterjet offset-mode turning
Geometrical error in abrasive waterjet turned parts is an important challenge toward the commercialization of abrasive waterjet turning process. A systematic study has not been done yet to investigate the effects of process parameters on geometrical error in abrasive waterjet offset-mode turning. In this article, a comprehensive study has been performed to investigate the influence of several machining parameters on the geometrical error (part diameter percent error) in turning AA2011-T4 aluminum alloy round bars. Water pressure, cutting head traverse speed, workpiece rotational speed, abrasive mass flow rate and depth of cut were considered as the main machining parameters in a five-level statistical experimental design. Based on central composite rotatable design, a total of 52 experiments were carried out. The main effects of the parameters and interactions among them were analyzed based on the analysis of variance technique, and the response contours for the part geometrical error were obtained using a quadratic regression model (i.e. response surface methodology). The model predictions were found to be in good agreement with experimental data. Furthermore, among the significant parameters, water pressure, depth of cut and traverse speed are the most influential parameters, with percent contribution of almost 25% each. Abrasive mass flow rate is the least influential parameter with a percent contribution of 4%.
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 621, 202-207
Modeling of Surface Waviness in Abrasive Waterjet Offset-Mode Turning
In this paper, surface waviness produced by turning aluminum parts with abrasive waterjet has been studied regarding changes in some process parameters. Effect of five major parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut have been investigated using analysis of variances. Second order regression model presented forwaviness.The validity of the model wasconfirmed bycomparing with experimental data. It found thatabrasive mass flow rate, cutting head traverse speed and DOC are the most influencing parameters while water pressure and workpiece rotational speed show lesser effectiveness.
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 621, 202-207
Modeling of Surface Waviness in Abrasive Waterjet Offset-Mode Turning
In this paper, surface waviness produced by turning aluminum parts with abrasive waterjet has been studied regarding changes in some process parameters. Effect of five major parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut have been investigated using analysis of variances. Second order regression model presented forwaviness.The validity of the model wasconfirmed bycomparing with experimental data. It found thatabrasive mass flow rate, cutting head traverse speed and DOC are the most influencing parameters while water pressure and workpiece rotational speed show lesser effectiveness.
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 599-601, 555-559
Surface Waviness in Abrasive Waterjet Offset-Mode Turning
In this paper, surface waviness quality in abrasive waterjet offset-mode turning has been studied regarding variations of some process parameters. Influence of five main operational parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut on surface waviness of turned parts have been investigated using statistical approach. Second order regression model presented for surface waviness. The model accuracy was verified by comparing with experimental data. It found that abrasive mass flow rate, cutting head traverse speed and DOC are the most influential parameters while water pressure and workpiece rotational speed show lesser effectiveness.
- 1 August 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 599-601, 555-559
Surface Waviness in Abrasive Waterjet Offset-Mode Turning
In this paper, surface waviness quality in abrasive waterjet offset-mode turning has been studied regarding variations of some process parameters. Influence of five main operational parameters such as water pressure, cutting head traverse speed, abrasive mass flow rate, workpiece rotational speed and depth of cut on surface waviness of turned parts have been investigated using statistical approach. Second order regression model presented for surface waviness. The model accuracy was verified by comparing with experimental data. It found that abrasive mass flow rate, cutting head traverse speed and DOC are the most influential parameters while water pressure and workpiece rotational speed show lesser effectiveness.
- Open Access
- 1 January 2014
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 6
Investigation of the Effects of Machining Parameters on Material Removal Rate in Abrasive Waterjet Turning
The effects of the main operational machining parameters on the material removal rate (MRR) in abrasive waterjet turning (AWJT) are presented in this paper using a statistical approach. The five most common machining parameters such as water pressure, abrasive mass flow rate, cutting head traverse speed, workpiece rotational speed, and depth of cut have been put into a five-level central composite rotatable experimental design (CCRD). The main effects of parameters and the interaction among them were analyzed by means of the analysis of variance (ANOVA) and the response surfaces for MRR were obtained fitting a second-order polynomial function. It has been found that depth of cut and cutting head traverse speed are the most influential parameters, whereas the rotational speed is insignificant. In addition, the investigations show that interactions between traverse speed and pressure, abrasive mass flow rate and depth of cut, and pressure and depth of cut are significant on MRR. This result advances the AWJT state of the art. A complete model discussion has been reported drawing interesting considerations on the AWJT process characterising phenomena, where parameters interactions play a fundamental role.
- 1 January 2014
- Published by SAGE Publications in Advances in Mechanical Engineering
- Vol. 6
Open AccessInvestigation of the Effects of Machining Parameters on Material Removal Rate in Abrasive Waterjet Turning
The effects of the main operational machining parameters on the material removal rate (MRR) in abrasive waterjet turning (AWJT) are presented in this paper using a statistical approach. The five most common machining parameters such as water pressure, abrasive mass flow rate, cutting head traverse speed, workpiece rotational speed, and depth of cut have been put into a five-level central composite rotatable experimental design (CCRD). The main effects of parameters and the interaction among them were analyzed by means of the analysis of variance (ANOVA) and the response surfaces for MRR were obtained fitting a second-order polynomial function. It has been found that depth of cut and cutting head traverse speed are the most influential parameters, whereas the rotational speed is insignificant. In addition, the investigations show that interactions between traverse speed and pressure, abrasive mass flow rate and depth of cut, and pressure and depth of cut are significant on MRR. This result advances the AWJT state of the art. A complete model discussion has been reported drawing interesting considerations on the AWJT process characterising phenomena, where parameters interactions play a fundamental role.
- 1 January 2010
- Published by ASME International
- p. 825-830
Mathematical Modeling of Abrasive Waterjet Turning of Ductile Materials
In this paper, an erosion-based model for abrasive waterjet (AWJ) turning process is presented. In the AWJ turning process a particular volume of material is removed by impacting of abrasive particles to the surface of the rotating cylindrical workpiece. This volume is estimated according to the modified Hashish erosion model; thus radius reduction at each revolution is calculated. The distinctively proposed model considers the continuous change in local impact angle due to change in workpiece diameter, axial traverse speed of the jet, the abrasive particle roundness and density. The accuracy of the proposed model is approved by experimental tests under various traverse speeds. The final diameters estimated by the new model are in good accordance with the experiments.
- 1 January 2010
- Published by ASME International
- p. 825-830
Mathematical Modeling of Abrasive Waterjet Turning of Ductile Materials
In this paper, an erosion-based model for abrasive waterjet (AWJ) turning process is presented. In the AWJ turning process a particular volume of material is removed by impacting of abrasive particles to the surface of the rotating cylindrical workpiece. This volume is estimated according to the modified Hashish erosion model; thus radius reduction at each revolution is calculated. The distinctively proposed model considers the continuous change in local impact angle due to change in workpiece diameter, axial traverse speed of the jet, the abrasive particle roundness and density. The accuracy of the proposed model is approved by experimental tests under various traverse speeds. The final diameters estimated by the new model are in good accordance with the experiments.
- 1 January 2010
- Published by ASME International
- p. 831-839
Modeling and Analysis of Hot Extrusion Metal Forming Process Using Artificial Neural Network and ANOVA
In this paper, a feed-forward back-propagation artificial neural network (BP-ANN) and analysis of variance (ANOVA) are applied to a hot metal extrusion process, establishing a black box model as well as analyzing the effects of relevant process parameters on required forging load, under different operating conditions. Some finite element simulation data on extruding ck-45 steel, adopted from a published research paper, were used to train the neural model employing Levenberg-Marquardt learning algorithm. Die angle (15°–75°), friction coefficient between billet-die material pair (0.4–0.8), punch velocity (168–203 mm/s), and billet temperature (1000°C–1260°C) were selected as the inputs, while the extrusion load (tone) was considered as the network’s output. Based on the results during modeling attempts, a 4-10-10-1 size neural network has been decided on as the appropriate architecture of the process model. Testing predictive accuracy of the developed model was also done using a new data set (8 data samples), which has not been used in the training phase. The comparative errors with respect to the desired FEM simulations are all in acceptable ranges (less than 12%) thereby the network’s generalization capabilities were confirmed. Having established the appropriate neural model, analysis of variance (ANOVA) technique was then applied to the original training data base to find and recognize the level of importance of each parameters and their possible dual interactions on the extrusion loading force within 95% of confidence interval (α = 0.05). Based on the obtained inferences, the best optimal combination of parametric settings which leads to the minimum required extruding load was then revealed and recommended. The optimally minimized extrusion force was then predicted by the trained network model. Neural network tool box (NNET) of the Matlab software and design of experiments module of Minitab software were employed as platforms to develop neural simulations and ANOVA technique, respectively. The overall results indicate the feasibility and effectiveness of the proposed approach in a real manufacturing environment and eliminate the need to carry out expensive as well as time consuming trial and error experimentations to reach to the optimum operating conditions.
- 1 January 2010
- Published by ASME International
- p. 831-839
Modeling and Analysis of Hot Extrusion Metal Forming Process Using Artificial Neural Network and ANOVA
In this paper, a feed-forward back-propagation artificial neural network (BP-ANN) and analysis of variance (ANOVA) are applied to a hot metal extrusion process, establishing a black box model as well as analyzing the effects of relevant process parameters on required forging load, under different operating conditions. Some finite element simulation data on extruding ck-45 steel, adopted from a published research paper, were used to train the neural model employing Levenberg-Marquardt learning algorithm. Die angle (15°–75°), friction coefficient between billet-die material pair (0.4–0.8), punch velocity (168–203 mm/s), and billet temperature (1000°C–1260°C) were selected as the inputs, while the extrusion load (tone) was considered as the network’s output. Based on the results during modeling attempts, a 4-10-10-1 size neural network has been decided on as the appropriate architecture of the process model. Testing predictive accuracy of the developed model was also done using a new data set (8 data samples), which has not been used in the training phase. The comparative errors with respect to the desired FEM simulations are all in acceptable ranges (less than 12%) thereby the network’s generalization capabilities were confirmed. Having established the appropriate neural model, analysis of variance (ANOVA) technique was then applied to the original training data base to find and recognize the level of importance of each parameters and their possible dual interactions on the extrusion loading force within 95% of confidence interval (α = 0.05). Based on the obtained inferences, the best optimal combination of parametric settings which leads to the minimum required extruding load was then revealed and recommended. The optimally minimized extrusion force was then predicted by the trained network model. Neural network tool box (NNET) of the Matlab software and design of experiments module of Minitab software were employed as platforms to develop neural simulations and ANOVA technique, respectively. The overall results indicate the feasibility and effectiveness of the proposed approach in a real manufacturing environment and eliminate the need to carry out expensive as well as time consuming trial and error experimentations to reach to the optimum operating conditions.