Pawel Kosinski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Pawel Kosinski has a total of 78 co-authors. Here are the top co-authors by number of shared publications:
- Alex Christian Hoffmann
Department of Physics and Technology, University of Bergen, Bergen, Norway
43 shared publications - Boris V. Balakin
Western Norway University of Applied Sciences
25 shared publications Theodore E. Simos
Department of Mathematics, College of Sciences, King Saud University, P.O. Box 2455, Riyadh 11451, Saudi Arabia
13 shared publicationsCh. Tsitouras
12 shared publicationsGeorge Psihoyios
12 shared publicationsArild Vik
7 shared publications
Latest Publications
- Open Access
- 31 October 2026
- Published by Elsevier in Renewable Energy
- Vol. 279
Numerical and experimental investigation of heat transfer in photothermal liquid films for parametric analysis of their applicability in photovoltaic–thermal (PV/T) systems
- 31 October 2026
- Published by Elsevier in Renewable Energy
- Vol. 279
Open AccessNumerical and experimental investigation of heat transfer in photothermal liquid films for parametric analysis of their applicability in photovoltaic–thermal (PV/T) systems
- Open Access
- 22 October 2026
- Published by Elsevier in SSRN Electronic Journal
Material Degradation and Particle Deposition in Carbon Black Nanofluid Systems
This study investigates the interaction between carbon black (CB) nanofluids and metallic surfaces, with emphasis on corrosion, nanoparticle deposition, and the potential contribution of erosion under stationary and rotating flow conditions. Aluminum, copper, and iron plates were exposed for 168 h to three aqueous systems: distilled water, tap water, and a 0.020 wt.% CB nanofluid stabilized with sodium dodecyl sulfate (SDS). Mass changes were quantified gravimetrically, while surface morphology and composition were characterized using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The results indicate that material degradation was governed primarily by electrochemical corrosion and surface chemistry rather than mechanical erosion, consistent with the low particle concentration and relatively mild hydrodynamic conditions investigated. Aluminum exhibited negligible corrosion, whereas nanoparticle deposition was strongly influenced by hydrodynamics, with rotation promoting greater and more heterogeneous nanoparticle deposition. Copper showed concurrent nanoparticle deposition and localized corrosion, with SEM revealing surface roughening and early-stage cracking, while supplementary tests suggested that SDS-containing environments may promote corrosion initiation. Iron was the most susceptible material, exhibiting extensive oxide formation and a strong coupling between corrosion processes and nanofluid stability, with the most pronounced destabilization occurring in SDS-stabilized suspensions. These findings emphasize that under the investigated conditions material performance in nanoparticle-containing fluids is governed primarily by the interplay between corrosion processes, surfactant chemistry, nanofluid stability, and flow conditions, rather than by nanoparticle-induced erosion.
- 22 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMaterial Degradation and Particle Deposition in Carbon Black Nanofluid Systems
This study investigates the interaction between carbon black (CB) nanofluids and metallic surfaces, with emphasis on corrosion, nanoparticle deposition, and the potential contribution of erosion under stationary and rotating flow conditions. Aluminum, copper, and iron plates were exposed for 168 h to three aqueous systems: distilled water, tap water, and a 0.020 wt.% CB nanofluid stabilized with sodium dodecyl sulfate (SDS). Mass changes were quantified gravimetrically, while surface morphology and composition were characterized using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The results indicate that material degradation was governed primarily by electrochemical corrosion and surface chemistry rather than mechanical erosion, consistent with the low particle concentration and relatively mild hydrodynamic conditions investigated. Aluminum exhibited negligible corrosion, whereas nanoparticle deposition was strongly influenced by hydrodynamics, with rotation promoting greater and more heterogeneous nanoparticle deposition. Copper showed concurrent nanoparticle deposition and localized corrosion, with SEM revealing surface roughening and early-stage cracking, while supplementary tests suggested that SDS-containing environments may promote corrosion initiation. Iron was the most susceptible material, exhibiting extensive oxide formation and a strong coupling between corrosion processes and nanofluid stability, with the most pronounced destabilization occurring in SDS-stabilized suspensions. These findings emphasize that under the investigated conditions material performance in nanoparticle-containing fluids is governed primarily by the interplay between corrosion processes, surfactant chemistry, nanofluid stability, and flow conditions, rather than by nanoparticle-induced erosion.
- Open Access
- 1 October 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (10)
On the practical use of carbon black nanofluids for solar thermal energy applications
This study explores the use of carbon black nanofluids in solar thermal energy systems, specifically focusing on their application in direct absorption solar collectors, where the working fluid directly absorbs incoming radiation. This work presents a novel combination of long-term stability testing, geometrical effects, and multi-method analysis (experimental, theoretical, and numerical) to evaluate the thermal performance of nanofluids. Uniquely, carbon black nanofluids stored under ambient conditions for two years were tested and compared with freshly prepared samples, a comparison not previously reported in the research literature. The influence of nanoparticle concentration, irradiation distance, and system geometry was investigated using two simplistic container configurations: a test tube and a volumetric flask. Results demonstrated that the optimal concentration depended on geometry and irradiation conditions. Stability tests showed minimal performance degradation over time, confirming their viability for long-term operation. A theoretical model and CFD simulations further supported the findings, offering insight into heat transfer mechanisms and the sensitivity of system performance to physical parameters. The results highlight the practical potential of low-concentration carbon black nanofluids in scalable solar thermal systems and underscore the importance of system design in maximizing efficiency.
- 1 October 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (10)
Open AccessOn the practical use of carbon black nanofluids for solar thermal energy applications
This study explores the use of carbon black nanofluids in solar thermal energy systems, specifically focusing on their application in direct absorption solar collectors, where the working fluid directly absorbs incoming radiation. This work presents a novel combination of long-term stability testing, geometrical effects, and multi-method analysis (experimental, theoretical, and numerical) to evaluate the thermal performance of nanofluids. Uniquely, carbon black nanofluids stored under ambient conditions for two years were tested and compared with freshly prepared samples, a comparison not previously reported in the research literature. The influence of nanoparticle concentration, irradiation distance, and system geometry was investigated using two simplistic container configurations: a test tube and a volumetric flask. Results demonstrated that the optimal concentration depended on geometry and irradiation conditions. Stability tests showed minimal performance degradation over time, confirming their viability for long-term operation. A theoretical model and CFD simulations further supported the findings, offering insight into heat transfer mechanisms and the sensitivity of system performance to physical parameters. The results highlight the practical potential of low-concentration carbon black nanofluids in scalable solar thermal systems and underscore the importance of system design in maximizing efficiency.
- Open Access
- 5 June 2023
- Published by Elsevier in Journal of Cleaner Production
- Vol. 414
Investigation of nanofluids in alkaline electrolytes: Stability, electrical properties, and hydrogen production
- 5 June 2023
- Published by Elsevier in Journal of Cleaner Production
- Vol. 414
Open AccessInvestigation of nanofluids in alkaline electrolytes: Stability, electrical properties, and hydrogen production
- Open Access
- 19 April 2023
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 37 (6) , 665-686
Experimental and numerical investigation of direct absorption solar collectors (DASCs) based on carbon black nanofluids
Direct absorption solar collectors (DASCs) typically achieve high efficiency due to the volumetric heat absorption process facilitated by the working fluids. In this study, carbon black (CB) nanofluids were utilized as the working fluid to experimentally and numerically investigate the thermal performance of a rectangular DASC. The findings suggest that the nanoparticles have the potential to enhance the efficiency of the DASC. Direct absorption solar collectors (DASCs) are known for their high efficiency, which is achieved through the volumetric heat absorption process provided by the working fluids In this study, carbon black (CB) nanofluids were used as these working fluids to study the thermal performance of a rectangular DASC. The experiments were conducted using water and nanofluids with 0.05 wt.% nanoparticle concentration, at different flow rates and tilt angles, under a concentrated simulated solar power source. Our results show that the efficiency of the DASC increased as the flow rate increased. The DASC was more efficient when the receiving surface was facing downwards (tilt angle of 0°), and the efficiency was 35% higher than when the receiving surface was facing upwards (tilt angle of 180°). A computational fluid dynamics (CFD) model, which was validated against our experimental results, analyzed the DASC performance under different CB concentrations. According to the simulations, the highest efficiency occurred at a concentration of 0.05 wt.%. The study also highlighted the distribution of temperature and velocity of the nanofluids, as well as the volume fraction of carbon black during the flow process.
- 19 April 2023
- Published by Taylor & Francis in Experimental Heat Transfer
- Vol. 37 (6) , 665-686
Open AccessExperimental and numerical investigation of direct absorption solar collectors (DASCs) based on carbon black nanofluids
Direct absorption solar collectors (DASCs) typically achieve high efficiency due to the volumetric heat absorption process facilitated by the working fluids. In this study, carbon black (CB) nanofluids were utilized as the working fluid to experimentally and numerically investigate the thermal performance of a rectangular DASC. The findings suggest that the nanoparticles have the potential to enhance the efficiency of the DASC. Direct absorption solar collectors (DASCs) are known for their high efficiency, which is achieved through the volumetric heat absorption process provided by the working fluids In this study, carbon black (CB) nanofluids were used as these working fluids to study the thermal performance of a rectangular DASC. The experiments were conducted using water and nanofluids with 0.05 wt.% nanoparticle concentration, at different flow rates and tilt angles, under a concentrated simulated solar power source. Our results show that the efficiency of the DASC increased as the flow rate increased. The DASC was more efficient when the receiving surface was facing downwards (tilt angle of 0°), and the efficiency was 35% higher than when the receiving surface was facing upwards (tilt angle of 180°). A computational fluid dynamics (CFD) model, which was validated against our experimental results, analyzed the DASC performance under different CB concentrations. According to the simulations, the highest efficiency occurred at a concentration of 0.05 wt.%. The study also highlighted the distribution of temperature and velocity of the nanofluids, as well as the volume fraction of carbon black during the flow process.
- Open Access
- 27 March 2023
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 190
Direct absorption solar collector: Use of nanofluids and biodegradable colloids
- 27 March 2023
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 190
Open AccessDirect absorption solar collector: Use of nanofluids and biodegradable colloids
- Open Access
- 3 January 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 47 (12) , 7522-7534
Experimental study of hydrogen production using electrolyte nanofluids with a simulated light source
- 3 January 2022
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 47 (12) , 7522-7534
Open AccessExperimental study of hydrogen production using electrolyte nanofluids with a simulated light source
- Open Access
- 1 May 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (5) , 055214
Use of biodegradable colloids and carbon black nanofluids for solar energy applications
The conversion of solar energy to heat can be performed in direct absorption solar collectors, where the radiation from the sun is absorbed by a fluid. There are various types of fluids that can be used, and recently, nanofluids (i.e., liquids with immersed nanoparticles) have been investigated by researchers. Nevertheless, nanofluids have inherent drawbacks such as cost, toxicity, and clogging. This paper considers the use of fluids that are inexpensive and neutral to the environment, namely, coffee colloids. These types of fluids have already been tested for solar energy applications, but they have not yet been compared with nanofluids. In this research, we conducted a series of simple experiments where both coffee colloids and carbon black nanofluids were analyzed under the same conditions. According to our results, the thermal efficiency of coffee colloid and the nanofluid systems is, respectively, 12% and 16% greater than that of pure water. In addition to the experiments, we developed a mathematical model that is based on the Beer–Lambert law and a heat balance equation. Despite its simplicity, the model predicts the results relatively well.
- 1 May 2021
- Published by AIP Publishing in AIP Advances
- Vol. 11 (5) , 055214
Open AccessUse of biodegradable colloids and carbon black nanofluids for solar energy applications
The conversion of solar energy to heat can be performed in direct absorption solar collectors, where the radiation from the sun is absorbed by a fluid. There are various types of fluids that can be used, and recently, nanofluids (i.e., liquids with immersed nanoparticles) have been investigated by researchers. Nevertheless, nanofluids have inherent drawbacks such as cost, toxicity, and clogging. This paper considers the use of fluids that are inexpensive and neutral to the environment, namely, coffee colloids. These types of fluids have already been tested for solar energy applications, but they have not yet been compared with nanofluids. In this research, we conducted a series of simple experiments where both coffee colloids and carbon black nanofluids were analyzed under the same conditions. According to our results, the thermal efficiency of coffee colloid and the nanofluid systems is, respectively, 12% and 16% greater than that of pure water. In addition to the experiments, we developed a mathematical model that is based on the Beer–Lambert law and a heat balance equation. Despite its simplicity, the model predicts the results relatively well.
- Open Access
- 1 January 2021
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 15 (1) , 180-193
A numerical study of flow field and particle deposition in nasal channels with deviant geometry
Deviant geometry of nasal channels results in significant changes to nasal aerodynamics that alter flow resistance, sensation, and the ability to filter aerosols. The invasive, operative modification of nasal geometry might alter the intranasal flow patterns, and this must be considered in advance at the stage of surgical planning. The present work describes flow patterns, reproduced numerically for several nasal geometries. This includes the reference channel geometry without physiological modifications. Making use of the commercial CFD-package STAR-CCM+, we document a down to 51% reduction and up to a 280% increase in nasal flow resistance for enlarged and obstructed channel geometries. The study on particle deposition revealed an only 18% deposition efficiency for the enlarged nasal cavities, while this parameter was up to 58% for the normal and obstructed geometries.
- 1 January 2021
- Published by Taylor & Francis in Engineering Applications of Computational Fluid Mechanics
- Vol. 15 (1) , 180-193
Open AccessA numerical study of flow field and particle deposition in nasal channels with deviant geometry
Deviant geometry of nasal channels results in significant changes to nasal aerodynamics that alter flow resistance, sensation, and the ability to filter aerosols. The invasive, operative modification of nasal geometry might alter the intranasal flow patterns, and this must be considered in advance at the stage of surgical planning. The present work describes flow patterns, reproduced numerically for several nasal geometries. This includes the reference channel geometry without physiological modifications. Making use of the commercial CFD-package STAR-CCM+, we document a down to 51% reduction and up to a 280% increase in nasal flow resistance for enlarged and obstructed channel geometries. The study on particle deposition revealed an only 18% deposition efficiency for the enlarged nasal cavities, while this parameter was up to 58% for the normal and obstructed geometries.
- 25 August 2020
- Published by American Physical Society (APS) in Physical Review E
- Vol. 102 (2) , 022909
Extension of the hard-sphere model for particle-flow simulations
Discrete element methods require appropriate models for particle-particle collisions. Usually, researchers use soft-sphere types of models where the collision dynamics is solved numerically. This makes the simulation computationally expensive. In this paper, however, we show a hard-sphere model that uses ready analytic formulas that relate the pre- and postcollisional velocities of the particles in contact. This hard-sphere model is an extension of an existing model that uses three input parameters. For this, we applied the linear-spring soft-sphere model, where analytic relations can be found. These relations were implemented into the standard hard-sphere model. As a result, we obtain a robust hard-sphere model that is more accurate than the standard one and is still computationally cheap.
- 25 August 2020
- Published by American Physical Society (APS) in Physical Review E
- Vol. 102 (2) , 022909
Extension of the hard-sphere model for particle-flow simulations
Discrete element methods require appropriate models for particle-particle collisions. Usually, researchers use soft-sphere types of models where the collision dynamics is solved numerically. This makes the simulation computationally expensive. In this paper, however, we show a hard-sphere model that uses ready analytic formulas that relate the pre- and postcollisional velocities of the particles in contact. This hard-sphere model is an extension of an existing model that uses three input parameters. For this, we applied the linear-spring soft-sphere model, where analytic relations can be found. These relations were implemented into the standard hard-sphere model. As a result, we obtain a robust hard-sphere model that is more accurate than the standard one and is still computationally cheap.