DJDazhi Jiang

Dazhi Jiang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dazhi Jiang has a total of 62 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Bio-inspired ”Unit-Thin-Ply” Helicoidal Laminates

    by Jialong Liu, Chongyang Kang, Nan Lin, Jinzhao Huang, Dazhi Jiang, Lei Teng, Licheng Guo, Vincent Beng Chye Tan

    Decreasing ply thickness of CFRP laminates leads to higher matrix damage resistance and greater design freedom. The authors recently developed CFRP laminates with only one row of fibers per ply (unit-thin-ply) and ply thickness below 8 μm. But extremely low ply thickness also reduces the fiber content and in-plane fracture toughness of the laminate. To address these shortcomings, bio-inspired helicoidal layup structure was implemented. Owing to the unique microstructure of helicoidal layups, the fiber weight content of the unit-thin-ply helicoidal laminate can reach 77.6%, whilst the fiber weight content of the unit-thin-ply laminates with the conventional QI layup is 65.1%. The in-plane modulus and strength of unit-thin-ply helicoidal laminates thus increase by up to 20% and 23.5%, respectively. New damage patterns were also observed in the unit-thin-ply laminates subjected to out-of-plane loading: Fiber fracture developed before large delamination in the unit-thin-ply QI laminate; Matrix cracks were formed first in unit-thin-ply helicoidal laminates, followed by fiber fracture upon load drop, which significantly improved their specific peak load by up to 137.1%. In the compact tension test, directional biased unit-thin-ply helicoidal laminate can divert the crack front and formed a unique dune-like fractured plane, whereas Quad counterpart exhibits short fiber pull-out. As a result, unit-thin-ply helicoidal laminate exhibits a 382.5% increase of in-plane fracture toughness, and can also prevent catastrophic fiber fracture observed in the Quad counterpart. The damage patterns of unit-thin-ply laminates and laminates with conventional ply thickness was also compared, and unit-thin-ply laminates showed outstanding delamination resistance.

  • Interface Interactions between In Situ Mechanically Exfoliated Graphene with Wrinkles and Edge Carboxyl Groups and Natural Rubber: Experimental and Modeling Investigations

    by Qungui Wei, Zixi Li, Wenduo Chen, Jialong Liu, Dazhi Jiang

    Enhancing interactions between graphene (GE) reinforcements and the rubber matrix can effectively improve the overall performance of rubber composites. In this work, a new method was developed to prepare in situ mechanically exfoliated graphene (IS-GE) with wrinkles and edge carboxyl groups by ball-milling graphite and natural rubber (NR) powder. Subsequently, IS-GE/carbon black/NR (IS-GE/CB/NR) composites were fabricated via mechanical mixing and vulcanization. The results indicated that the wrinkle degree and the oxygen content of the IS-GE could be controlled by the ball-milling time. The highest mechanical properties and thermal conductivity of the IS-GE/CB/NR composite were achieved by adding 10 phr (parts per hundred rubber) IS-GE that had undergone ball-milling for 24 h. By integrating experimental characterization with molecular dynamics (MD) simulations, this research quantified microstructure–property correlations in the IS-GE/NR composites by taking into account the wrinkles and edge carboxyl groups of the GE. The interfacial interactions between IS-GE and NR increased with an increasing wrinkle degree and edge carboxyl group content. The MD simulations showed that the NR in the IS-GE/NR composite with 8.01% oxygen content from edge carboxyl groups on the IS-GE had the lowest mean square displacement (MSD) and fractional free volume (FFV), which indicated that the IS-GE presented a strong adsorption effect on the NR molecular chains and reduced GE agglomeration. Young’s modulus of the NR composites was significantly enhanced with increasing GE wrinkle degree. This research provides new molecular-level insights into the design of GE/NR composites with high mechanical and thermal properties, as well as low fatigue temperature rise.

  • Open Access

    Molecular Dynamics Study on Toughing Mechanism of Cured Epoxy Resin and Poly-dicyclopentadiene Interpenetrating polymer Networks via Simultaneous Frontal Polymerizing

    by Siqi Huang, Zixi Li, Qungui Wei, Dazhi Jiang

    Bisphenol-A epoxy resins (BADGE) exhibit high tensile strength and modulus but suffer from inherent brittleness due to their high crosslinking density. The interpenetrating polymer networks (IPNs) of epoxy resin can effectively reduce its brittleness, as external forces can be transferred and dispersed more efficiently through the interwoven network structure, preventing excessive stress concentration. A novel epoxy-based IPNs was synthesized by frontal polymerization using BADGE and dicyclopentadiene (DCPD) since the above two monomers can be initiated synchronously under the same triggering condition of heating or UV light. Atomistic molecular dynamics (MD) simulations construct randomly crosslinked hybrid networks to replicate actual curing kinetics. Besides, we utilize MD simulations to elucidate the dependence of IPNs macroscopic mechanical properties on their microstructure. The crosslinking model accurately predicts thermomechanical properties while establishing an efficient construction methodology. This work reveals molecular-scale fracture mechanisms in BADGE/DCPD IPNs.

  • Fatigue Temperature Rise of Nano‐Carbon Filler Reinforced Rubber Composites: A Comprehensive Review

    by Qungui Wei, Siqi Huang, Wenduo Chen, Jialong Liu, Dazhi Jiang

    It is of technological and scientific importance to limit fatigue temperature rise of rubber composites reinforced with nano‐carbon filler so as to decrease negative impacts on performance. The fatigue temperature rise is the result of thermal conductivity and heat generation in rubber composites. However, the insufficient understanding of thermal conductivity and heat generation in rubber composites imposes restrictions on the design and preparation of materials with lower fatigue temperature rise. This review aims to explore the fatigue temperature rise mechanisms by analyzing the influences of various nano‐carbon fillers in rubber composites on dynamic heat generation and thermal conduction mechanisms. Factors defined by rubber matrix (e.g., chain structures and crosslinking density) and nano‐carbon filler (e.g., intrinsic thermal conductivity, filler loading, size, shape and aspect ratio, hybrid type, functionalization, etc.) are proved to exert an influence on the fatigue temperature rise of nano‐carbon filler reinforced rubber composites. Importantly, the interface between the rubber matrix and nano‐carbon filler is the main parameter used to determine the fatigue temperature rise of rubber composites. Finally, molecular dynamics simulation methods for predicting fatigue temperature rise of rubber composites are discussed as well. This review can provide some guidance for future studies in low fatigue temperature rise of rubber composites reinforced with nano‐carbon filler for developing a new generation of energy‐saving and durable rubber composites.


  • Open Access

    Highly-Oriented Polylactic Acid Fiber Reinforced Polycaprolactone Composite Produced by Infused Fiber Mat Process for 3D Printed Tissue Engineering Technology

    by Zhipeng Deng, Chen Rao, Simin Han, Qungui Wei, Yichen Liang, Jialong Liu, Dazhi Jiang

    Three-dimensional printed polycaprolactone (PCL) tissue engineering scaffolds have drawn increasing interest from the medical industry due to their excellent biocompatibility and biodegradability, yet PCL’s poor mechanical performance has limited their applications. This study introduces a biocompatible and biodegradable polylactic acid (PLA) fiber reinforced PCL (PLA/PCL) composite as the filament for 3D printed scaffolds to significantly enhance their mechanical performance: Special-made PLA short fiber mat was infused with PCL matrix and rolled into PLA/PCL filaments through a “Vacuum Assisted Resin Infusion” (VARI) process. The investigation revealed that the PLA fibers are highly oriented along the printing direction when using this filament for 3D printing due to the unique microstructure formed during the VARI process. At the same PLA fiber content, the percentage increase in Young’s modulus of the 3D printed strands using the filaments produced by the VARI process is 127.6% higher than the 3D printed strands using the filaments produced by the conventional melt blending process. The 3D printed tissue engineering scaffolds using the PLA/PCL composite filament with 11 wt% PLA fiber content also achieved an exceptional 84.2% and 143.3% increase in peak load and stiffness compared to the neat PCL counterpart.


  • Synthesis and characterization of epoxy resin‐polydicyclopentadiene interpenetrating polymer networks by UV‐initiated simultaneously frontal polymerization

    by Zhenjie Yuan, Siqi Huang, Wenduo Chen, Dazhi Jiang

    By combination of UV curing and frontal polymerization, interpenetrating polymer networks (IPNs) based on diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin and polydicyclopentadiene (PDCPD) were prepared by UV‐induced simultaneously frontal polymerization in this paper. Compared with the net DGEBA cured polymer, the tensile strength, elongation at break and impact strength of the IPNs were simultaneously improved. The maximum tensile strength and elongation at break of the IPNs reached 100 MPa and 4.64%, respectively, and the maximum impact strength reached 7.34KJ/m2 with an improvement of 115.2% over that of the net DGEBA cured polymer. Thermogravimetric analysis (TGA) results revealed that the IPNs could enhance the thermal stability. Data of the differential scanning calorimetry (DSC) and TGA testing shows that the IPN shows a single glass transition temperature (Tg) which is between the Tg of DGEBA and DCPD, indicating homogeneous phase and highly cross‐linked IPN formed. Morphologies and molecular structure of the IPNs polymer were observed by scanning electron microscope (SEM) and characterized by Fourier transform infrared spectroscopy (FTIR), respectively, whose results also proved the formation of ideal IPNs structures.


  • Open Access

    Effects of graphene and carbon nanotubes on mechanical enhancement and heat generation of rubber composites

    by Y Liu, W D Chen, D Z Jiang

    Carbon nanofillers can enhance both thermal and mechanical properties of rubbers due to their high thermal conductivity and tensile strength at the nanoscale. But the effects of CNTs and GR on heat generation of rubber composites are yet unclear. In this paper, carbon nanotubes/carbon black/nature rubber (CNTs/CB/NR) composites and graphene/carbon black/nature rubber (GR/CB/NR) composites were prepared by using GR and CNTs as partial replacements for carbon black, respectively. The interfacial interactions between fillers and the rubber matrix were calculated by the contact angle test, the filler-matrix network was characterized by rubber processing analyzer, and the glass transition temperature of the composite was measured by dynamic mechanical analysis. Compared with CNT or CB, GR can be well wetted by NR and uniformly distributed in NR, so there was a strong interfacial interaction between them. The better interfacial interaction will promote the formation of a good network structure between the filler and the NR, and the network structure between the filler and NR further restricts the movement of rubber molecule chains. Therefore, the heat generation by the movement of the molecule chains is decreased, and the mechanical properties of the rubber composites are increased.


  • Graphene/carbon nanotube/polypyrrole composite films for electromagnetic interference shielding

    by Zhixiang Xie, Huaiyu Chen, Sikun Hu, Hongchao Zhao, Wenduo Chen, Dazhi Jiang

    Polypyrrole (PPy), an ideal organic electroactive material, shows limited application in the field of electromagnetic interference (EMI) shielding for its relatively low shielding effectiveness (SE), significant stiffness, difficult solubility, and poor processing performance. A strategy is proposed to construct three‐dimensional network structures of graphene/CNT/polypyrrole by electrochemical deposition to improve the EMI SE of polypyrrole composite films. In the graphene/CNT/polypyrrole films, the graphene/CNT substrates form the skeletons, and polypyrrole acts as bridges between graphene sheets and CNTs to form percolation networks in the multiphase and multihierarchical nanocomposites. When the deposition time increases to 80 min, the content of polypyrrole increases to 30 wt%, the conductivity improves by 27.7%, and the EMI SE improves by 11.4% at X‐band. The final film thickness is 249 μm, the conductivity is 3.06 S/mm, and the average EMI SE is 59.6 dB.