MNMikael Nygårds

Mikael Nygårds

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mikael Nygårds has a total of 28 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Quantification of damage generated during Fortuna splitting of paperboards

    by Adam Attemalm, Mikael Nygårds

    Accurate ply-specific properties are critical for predictive modeling and process optimization in paperboard manufacturing, yet the widely used Fortuna splitting technique may alter mechanical properties. This study addresses the gap by quantifying the damage introduced when three-ply paperboards are separated into individual plies using a Fortuna splitting machine. While grammage remains unaffected, splitting increases surface roughness and slightly inflates measured thickness, requiring correction for accurate laminate modelling. Tensile tests and curve-fitting reveal that splitting reduces the elastic stiffness and yield strength of free-laid plies compared to intact boards. Average reductions were determined as 11 % in tensile stiffness and 7 % in yield strength. Damage distribution is highly non-uniform: the middle ply exhibits the greatest degradation, up to 29 % stiffness loss in CD, while the outer plies are less affected. Splitting quality and direction significantly influence the magnitude of damage; cuts following interfaces minimize damage, whereas cuts propagating through plies increase bond disruption. By introducing damage-compensated properties, the intact board response can be accurately reconstructed from ply data, allowing for reliable finite element modeling. These findings underscore the importance of controlled splitting procedures and correction factors when utilizing free-laid ply properties for design and process optimization.


  • Open Access

    Rate-dependent tensile properties of paperboard and its plies

    by Satyasarathi Poddar, Eskil Andreasson, Mikael Nygårds

    Tensile properties of paperboard have been characterized, and it has been shown that paper tensile properties are dependent on the strain rate. Tensile testing was done using strain rates in the range 10−4–3 s−1, which corresponds to crosshead movements ranging from 1 up to 24,000 mm/min, using an electro-mechanical testing machine. Two paperboards, and its free-laid top, middle and bottom plies were characterized in MD and CD. The testing was limited by the maximum crosshead speed of the testing machine. Initially 50 mm (grip to grip) long samples were tested, but to test even higher strain rates also short samples with length of 5 mm were tested. The results showed that ultimate strength increased by 9 % per decade increasing of testing rate, and Young’s modulus increased by 7 %. This shows that the previously reported rule of thumb of 10 % increase of in-plane strength per decade increase of strain rate holds. The testing here shows that this is valid also at strain rates as high as 3 s−1. Moreover, the strain at break in CD for long tensile specimens was observed to decrease when the strain rate exceeded 0.1 s−1, which resulted in straighter crack paths.


  • Open Access

    Relating papermaking process parameters to properties of paperboard with special attention to through-thickness design

    by Mikael Nygårds

    A biaxial stress state has been proposed to formulate a failure criterion for paperboard during bending. About 100 paperboards have been splitted, such that top, middle, and bottom plies have been free-laid and tested in the machine direction, cross-machine direction as well as in out-of-plane direction (ZD). The purpose was to determine the failure stresses and its dependency of papermaking parameters: density, degree of orientation, and fiber length for each layer. A linear model to predict the geometrical strength of a plies was suggested. Analytically simulations of different paperboard structures behavior during bending were performed. The density of the middle ply affected the location of the failure position in ZD, as well as the maximum bending moment. The impact of orientation and degree of anisotropy was simulated, which can be used to optimize the ZD property gradient by tweaking the properties, and hence optimize paperboard performance. Graphical abstract


  • Experimental quantification of differences in damage due to in‐plane tensile test and bending of paperboard

    by Gustav Marin, Mikael Nygårds, Sören Östlund

    Creasing is an essential process to convert paperboards into packages since it enables folding along well‐defined lines. The creasing process relies on purpose‐made damage that is initiated in the paperboard structure: delamination. However, creasing might also cause in‐plane cracks, which must be avoided. In this laboratory study, three paperboards were creased at six different depths, respectively. Two mechanical tests were performed to characterize the creases at standard climate (23°C and 50% RH): 2‐point folding, to examine the bending force and short‐span in‐plane tensile test to evaluate the strength. The results were normalized with the values for the uncreased boards, which gave the relative strength ratios: relative creasing strength (RCS) and relative tensile strength (RTS). When the relative strengths were evaluated against the normative shear strains, a creasing window was formed. This window has an upper limit given by the RTS values, corresponding to the in‐plane cracks, and a lower limit given by the RCS values, corresponding to the delamination damage initiated in the paperboard during creasing. It was observed that both the RCS and RTS values exhibit a linear relation against normative shear strain. From this, it was concluded that performing tests at two creasing depths might be sufficient to estimate the lower, and upper, limits for the creasing window in future studies. Finally, the effect of moisture was investigated by creasing, folding and tensile testing at 23°C and 90% RH, which showed that moisture had no clear effect on the RCS or the RTS values.


  • Simulation and experimental verification of a drop test and compression test of a gable top package

    by Mikael Nygårds, Stefan Sjökvist, Gustav Marin, Jonas Sundström


  • Finite Element Analysis of Hot Melt Adhesive Joints in Carton Board

    by Nils Hallbäck, Christer Korin, Christophe Barbier, Mikael Nygårds


  • Analysis of the plastic and elastic energy during the deformation and rupture of a paper sample using thermography

    by Caroline Hyll, Hannes Vomhoff, Mikael Nygårds

    Thermography has been used to quantitatively analyze the plastic and elastic energy during deformation of paper. Sack paper samples were subjected to uniaxial tensile testing until rupture occurred. The temperature of the sample was simultaneously recorded with an infrared camera. The mechanical energy invested in the deformation was determined based on the force and deformation data. The thermal energy that accumulated in the sample during testing was estimated using the temperature measurements. Here, special attention was put on using the correct emittance values for the sack paper by measuring it with a new method. When comparing exerted mechanical energy with released thermal energy up to the time of sample rupture, about 40% to 60% of the mechanical energy could be detected as thermal energy. The lacking share of heat was most likely lost due to cooling of the sample during the experiments, as a lower share of detected mechanical energy was obtained for longer experiments. When comparing the increase in thermal energy during rupture to the elastic energy stored in the sample, an agreement of better than 90% was found.


  • Stress-strain curve of paper revisited

    by Svetlana Borodulina, Artem Kulachenko, Mikael Nygårds, Sylvain Galland

    We have investigated a relation between micromechanical processes and the stress-strain curve of a dry fiber network during tensile loading. By using a detailed particle-level simulation tool we investigate, among other things, the impact of “non-traditional” bonding parameters, such as compliance of bonding regions, work of separation and the actual number of effective bonds. This is probably the first three-dimensional model which is capable of simulating the fracture process of paper accounting for nonlinearities at the fiber level and bond failures. The failure behavior of the network considered in the study could be changed significantly by relatively small changes in bond strength, as compared to the scatter in bonding data found in the literature. We have identified that compliance of the bonding regions has a significant impact on network strength. By comparing networks with weak and strong bonds, we concluded that large local strains are the precursors of bond failures and not the other way around.