Deepak Singh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Deepak Singh has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Paavo Rasilo
Electrical Engineering Unit, Tampere University, Tampere, Finland
19 shared publications - Anouar Belahcen
Aalto University
11 shared publications - Ugur Aydin
Department of Electrical Engineering and Automation, Aalto University, Espoo, Finland
9 shared publications A. Arkkio
7 shared publications- Reijo Kouhia
Tampere University
7 shared publications F. Martin
6 shared publications
Latest Publications
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (4) , 2736-2746
Characterizing the Effect of Shrink Fitting of Stator Housings on Electric Vehicle Performance
High performance rotating electric machines are a necessity in the automotive sector. The characteristics of electric steel materials given in the datasheet used in electric machines do not account for the effect of stress due to the manufacturing process. It is possible to account for the effect of stress coming more precisely from stator housings after press and shrink fitting which degrades the loss properties of electrical steel. A process is developed, which includes the development of a test bench for characterizing the magnetic properties of electric steel when put under compressive stress. The proposed hardware setup is a novel test bench capable of achieving high compressive stress up to 60 MPa and for a maximum of 1 kHz fundamental frequency. A modified compressive stress dependent loss model for analyzing impact on the total power loss is proposed. Further, a coupled multiphysics finite element analysis including structural and magnetic analysis to evaluate the machine performance over the entire operating range and vehicle performance over relevant drive cycles for passenger electric vehicles. A 7% increase in total machine losses was found at an average in a WLTC class-3 drive cycle due to shrink and press fitting of the stator housing.
- 14 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Energy Conversion
- Vol. 40 (4) , 2736-2746
Characterizing the Effect of Shrink Fitting of Stator Housings on Electric Vehicle Performance
High performance rotating electric machines are a necessity in the automotive sector. The characteristics of electric steel materials given in the datasheet used in electric machines do not account for the effect of stress due to the manufacturing process. It is possible to account for the effect of stress coming more precisely from stator housings after press and shrink fitting which degrades the loss properties of electrical steel. A process is developed, which includes the development of a test bench for characterizing the magnetic properties of electric steel when put under compressive stress. The proposed hardware setup is a novel test bench capable of achieving high compressive stress up to 60 MPa and for a maximum of 1 kHz fundamental frequency. A modified compressive stress dependent loss model for analyzing impact on the total power loss is proposed. Further, a coupled multiphysics finite element analysis including structural and magnetic analysis to evaluate the machine performance over the entire operating range and vehicle performance over relevant drive cycles for passenger electric vehicles. A 7% increase in total machine losses was found at an average in a WLTC class-3 drive cycle due to shrink and press fitting of the stator housing.
- Open Access
- 14 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (3) , 1-10
Rotational Single Sheet Tester for Multiaxial Magneto-Mechanical Effects in Steel Sheets
A detailed design of a new rotational single sheet tester device which allows comprehensive multiaxial magneto-mechanical analysis of ferromagnetic sheets is proposed. The challenges that arose during the mechanical and magnetic design phases are addressed. The applicability of the device is tested by performing magneto-mechanical measurements on an M400-50A electrical steel sheet. Results under several multiaxial magneto-mechanical loadings with circular and alternating magnetic flux densities are reported. It is shown that the effect of multiaxial stress on iron losses can be much more significant than that of uniaxial stress.
- 14 January 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 55 (3) , 1-10
Open AccessRotational Single Sheet Tester for Multiaxial Magneto-Mechanical Effects in Steel Sheets
A detailed design of a new rotational single sheet tester device which allows comprehensive multiaxial magneto-mechanical analysis of ferromagnetic sheets is proposed. The challenges that arose during the mechanical and magnetic design phases are addressed. The applicability of the device is tested by performing magneto-mechanical measurements on an M400-50A electrical steel sheet. Results under several multiaxial magneto-mechanical loadings with circular and alternating magnetic flux densities are reported. It is shown that the effect of multiaxial stress on iron losses can be much more significant than that of uniaxial stress.
- Open Access
- 1 October 2017
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 439, 82-90
Magneto-mechanical modeling of electrical steel sheets
- 1 October 2017
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 439, 82-90
Open AccessMagneto-mechanical modeling of electrical steel sheets
- Open Access
- 22 August 2017
- Published by Rakenteiden mekaniikka in Rakenteiden Mekaniikka
- Vol. 50 (3) , 349-352
A model for magneto-elastic behaviour
In this paper, a coupled magnetoelastic model for isotropic ferromagnetic materialsis presented. The constitutive equations are written on the basis of the total energy in whichthe right Cauchy-Green strain tensor and the Lagrangian form of the magnetic eld strengthare used as the basic state variables. It is also applied to ferromacnetic electric steel for whichthe material parameters are calibrated.
- 22 August 2017
- Published by Rakenteiden mekaniikka in Rakenteiden Mekaniikka
- Vol. 50 (3) , 349-352
Open AccessA model for magneto-elastic behaviour
In this paper, a coupled magnetoelastic model for isotropic ferromagnetic materialsis presented. The constitutive equations are written on the basis of the total energy in whichthe right Cauchy-Green strain tensor and the Lagrangian form of the magnetic eld strengthare used as the basic state variables. It is also applied to ferromacnetic electric steel for whichthe material parameters are calibrated.
- Open Access
- 22 August 2017
- Published by Rakenteiden mekaniikka in Rakenteiden Mekaniikka
- Vol. 50 (3) , 372-375
Preliminary results on the effect of plastic deformation on magnetic properties
In this paper some preliminary results on the eect of plastic deformation onmagnetic properties of an electric steel are presented. Both experimental results and modellingaspects are discussed.
- 22 August 2017
- Published by Rakenteiden mekaniikka in Rakenteiden Mekaniikka
- Vol. 50 (3) , 372-375
Open AccessPreliminary results on the effect of plastic deformation on magnetic properties
In this paper some preliminary results on the eect of plastic deformation onmagnetic properties of an electric steel are presented. Both experimental results and modellingaspects are discussed.
- 25 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (6) , 1-4
Modeling the Effect of Multiaxial Stress on Magnetic Hysteresis of Electrical Steel Sheets: A Comparison
The abilities of a simplified multiscale and a Helmholtz energy HE models models from the literature to predict the multiaxial stress dependent magnetic hysteresis behavior of electrical steel sheets are analyzed. The identification of the models is performed using only uniaxial magneto-mechanical measurements. Reasonable accuracy between the measurements and the modeled results is obtained. With this paper, the applicability of the HE-based model for predicting the multiaxial magneto-mechanical behavior of electrical steel sheets is verified for the first time. The differences between the studied models and possible modifications to increase the accuracy of them are discussed. Some brief guidelines for the applications are given.
- 25 January 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 53 (6) , 1-4
Modeling the Effect of Multiaxial Stress on Magnetic Hysteresis of Electrical Steel Sheets: A Comparison
The abilities of a simplified multiscale and a Helmholtz energy HE models models from the literature to predict the multiaxial stress dependent magnetic hysteresis behavior of electrical steel sheets are analyzed. The identification of the models is performed using only uniaxial magneto-mechanical measurements. Reasonable accuracy between the measurements and the modeled results is obtained. With this paper, the applicability of the HE-based model for predicting the multiaxial magneto-mechanical behavior of electrical steel sheets is verified for the first time. The differences between the studied models and possible modifications to increase the accuracy of them are discussed. Some brief guidelines for the applications are given.
- 3 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 50, 1861-1867
Magneto-mechanical analysis of an axially laminated synchronous reluctance machine
The performance of an axially laminated synchronous reluctance motor is calculated by considering the magneto-mechanical interaction on the electrical steel sheets. The elasticity analysis is performed with 2D finite element method for centrifugal force and shrink-fittings in both the stator frame and the rotor shaft. The 2D magnetostatic analysis is formulated with a mixed formulation involving the magnetic field in edge finite elements. The stress distribution and the components of the magnetic field affect locally the magnetic permeability of the electrical steel sheets. Their constitutive laws account for this magneto-mechanical effect with an equivalent stress approach. With a fixed-point method, this non-linear magneto-static problem is solved and the computation of the torque and the magnetic losses is performed in post-processing. Finally, the effect of the mechanical loads can increase the magnetic losses by 4.1 % mainly due to the stator shrink-fittings, whereas the electromagnetic torque only slightly decreases.
- 3 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 50, 1861-1867
Magneto-mechanical analysis of an axially laminated synchronous reluctance machine
The performance of an axially laminated synchronous reluctance motor is calculated by considering the magneto-mechanical interaction on the electrical steel sheets. The elasticity analysis is performed with 2D finite element method for centrifugal force and shrink-fittings in both the stator frame and the rotor shaft. The 2D magnetostatic analysis is formulated with a mixed formulation involving the magnetic field in edge finite elements. The stress distribution and the components of the magnetic field affect locally the magnetic permeability of the electrical steel sheets. Their constitutive laws account for this magneto-mechanical effect with an equivalent stress approach. With a fixed-point method, this non-linear magneto-static problem is solved and the computation of the torque and the magnetic losses is performed in post-processing. Finally, the effect of the mechanical loads can increase the magnetic losses by 4.1 % mainly due to the stator shrink-fittings, whereas the electromagnetic torque only slightly decreases.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Modelling the effect of multiaxial stress on magnetic hysteresis of electrical steel sheets: A comparison
A simplified multiscale approach and a Helmholtz energy based approach for modelling the multiaxial stress dependent magnetic hysteresis behavior of electrical steel sheets are compared. The models are identified from uniaxial magneto-mechanical measurements. Both approaches model the hysteresis losses under multiaxial stresses with reasonable accuracy compared to the measurements.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Modelling the effect of multiaxial stress on magnetic hysteresis of electrical steel sheets: A comparison
A simplified multiscale approach and a Helmholtz energy based approach for modelling the multiaxial stress dependent magnetic hysteresis behavior of electrical steel sheets are compared. The models are identified from uniaxial magneto-mechanical measurements. Both approaches model the hysteresis losses under multiaxial stresses with reasonable accuracy compared to the measurements.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 67, 1
Demagnetization field in a uniformly magnetized ellipsoid embedded in an infinite anisotropic media
In this paper, we determine analytically the demagnetization field within a uniformly magnetized ellipsoid embedded in an infinite anisotropic media. The anisotropic boundary condition consists of decomposing the external magnetization into an isotropic part parallel to the external field and an anisotropic part. The resulting demagnetization field within the ellipsoid is then calculated by superposing the demagnetization fields produced by the ellipsoid magnetization, the isotropic part of the external magnetization and field, and the anisotropic part of the external magnetization. Such computation is needed in developing accurate anisotropic multi-scale models of electrical steel sheets, for example.
- 1 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 67, 1
Demagnetization field in a uniformly magnetized ellipsoid embedded in an infinite anisotropic media
In this paper, we determine analytically the demagnetization field within a uniformly magnetized ellipsoid embedded in an infinite anisotropic media. The anisotropic boundary condition consists of decomposing the external magnetization into an isotropic part parallel to the external field and an anisotropic part. The resulting demagnetization field within the ellipsoid is then calculated by superposing the demagnetization fields produced by the ellipsoid magnetization, the isotropic part of the external magnetization and field, and the anisotropic part of the external magnetization. Such computation is needed in developing accurate anisotropic multi-scale models of electrical steel sheets, for example.
- 11 July 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 52 (11) , 1-9
Magnetomechanical Model for Hysteresis in Electrical Steel Sheet
A coupled magnetomechanical model for hysteresis in an electrical steel sheet is presented. The foundation of the model developed is the classical Sablik-Jiles-Atherton (SJA) model. A comprehensive model for the stress-dependent magnetostriction is also proposed and implemented in the SJA model. Improvements in the SJA model as well are proposed and validated with simultaneous measurements of magnetostriction, magnetic field, and flux density. The measurements were performed on a single electrical steel sheet under various levels of stress (-35 to 100 MPa). The proposed model was found to adequately model the permeability change and the local bowing of the B-H-loop due to stress.
- 11 July 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 52 (11) , 1-9
Magnetomechanical Model for Hysteresis in Electrical Steel Sheet
A coupled magnetomechanical model for hysteresis in an electrical steel sheet is presented. The foundation of the model developed is the classical Sablik-Jiles-Atherton (SJA) model. A comprehensive model for the stress-dependent magnetostriction is also proposed and implemented in the SJA model. Improvements in the SJA model as well are proposed and validated with simultaneous measurements of magnetostriction, magnetic field, and flux density. The measurements were performed on a single electrical steel sheet under various levels of stress (-35 to 100 MPa). The proposed model was found to adequately model the permeability change and the local bowing of the B-H-loop due to stress.