Raoul-Amadeus Lorbeer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Raoul-Amadeus Lorbeer has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
Stefan Scharring
Deutsches Zentrum für Luft- und Raumfahrt e.V. (Germany)
4 shared publicationsJochen Speiser
3 shared publicationsLukas Eisert
Institute of Technical Physics, German Aerospace Center (DLR), Stuttgart
3 shared publications- Oliver Kliebisch
Institute of Technical Physics, German Aerospace Center, Pfaffenwaldring 38-40, 70569 Stuttgart, Germany
3 shared publications - Thomas Dekorsy
German Aerospace Center, Institute of Technical Physics, Stuttgart, Germany
3 shared publications Benjamin Ewers
Deutsches Zentrum für Luft- und Raumfahrt e.V. (Germany)
2 shared publications
Latest Publications
- Open Access
- 14 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (21) , 40240
Phase and amplitude pre-shaping for a high-power ps-wedged thin-disk amplifier
Wedged thin-disk amplifiers offer a compact, monolithic alternative to conventional thin-disk multipass systems. As a trade-off, the wedged shape inherently introduces complex thermal lensing and phase distortions, degrading beam quality at high output powers. We demonstrate a spatial light modulator based adaptive phase and amplitude correction system for pre-compensation of aberrations. Utilizing the large acceptance angle of the wedged thin-disk, the adaptive element can be introduced before the optical amplification. Starting with M 2 ≃ 1.2 at 25 W, we obtain near diffraction limited beam quality M 2 = 1.3 for 150 W of output power, estimate a good beam quality (M 2 < 2) for up to 250 W, and reach up to 330 W of average power. This demonstrates the readiness of the technology for modern industrial and scientific applications.
- 14 October 2026
- Published by Optica Publishing Group in Optics Express
- Vol. 34 (21) , 40240
Open AccessPhase and amplitude pre-shaping for a high-power ps-wedged thin-disk amplifier
Wedged thin-disk amplifiers offer a compact, monolithic alternative to conventional thin-disk multipass systems. As a trade-off, the wedged shape inherently introduces complex thermal lensing and phase distortions, degrading beam quality at high output powers. We demonstrate a spatial light modulator based adaptive phase and amplitude correction system for pre-compensation of aberrations. Utilizing the large acceptance angle of the wedged thin-disk, the adaptive element can be introduced before the optical amplification. Starting with M 2 ≃ 1.2 at 25 W, we obtain near diffraction limited beam quality M 2 = 1.3 for 150 W of output power, estimate a good beam quality (M 2 < 2) for up to 250 W, and reach up to 330 W of average power. This demonstrates the readiness of the technology for modern industrial and scientific applications.
- Open Access
- 26 November 2024
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 16 (1) , 231-242
Flight testing of laser-optical techniques for future optical air data sensors
Optical air data sensors, which can serve as alternatives or supplements to traditional air data systems, have been a subject of ongoing research. These remote sensing optical sensors offer the advantage of measuring primary air data parameters in undisturbed airflow. As active sensors, they can self-diagnose, associating each measurement with an uncertainty and accounting for signal loss due to factors such as icing or light blocking, thus avoiding silent false measurements. In this paper, we discuss a recent flight test campaign of optical measurement techniques for potential development into air data sensors for future aircraft. We used laser Doppler anemometry, which relies on aerosol scattering of laser light, to observe the Doppler shift of scattered light from multiple directions. This enables the reconstruction of the full wind vector and the retrieval of true air speed, angle of attack, and angle of sideslip. A second instrument used tunable diode laser absorption spectroscopy, which measures an individual transition of molecular oxygen in the A band, in order to extract the static pressure from the observed collisional broadening. The techniques were implemented as airborne research instruments on the DLR’s Dassault Falcon 20 aircraft and tested in two campaigns in 2022 under different atmospheric conditions and dynamic maneuvers. We present results from these campaigns, focusing on general sensor performance, measurement rates, accuracy, and experimental challenges that need to be addressed for future applications.
- 26 November 2024
- Published by Springer Nature in CEAS Aeronautical Journal
- Vol. 16 (1) , 231-242
Open AccessFlight testing of laser-optical techniques for future optical air data sensors
Optical air data sensors, which can serve as alternatives or supplements to traditional air data systems, have been a subject of ongoing research. These remote sensing optical sensors offer the advantage of measuring primary air data parameters in undisturbed airflow. As active sensors, they can self-diagnose, associating each measurement with an uncertainty and accounting for signal loss due to factors such as icing or light blocking, thus avoiding silent false measurements. In this paper, we discuss a recent flight test campaign of optical measurement techniques for potential development into air data sensors for future aircraft. We used laser Doppler anemometry, which relies on aerosol scattering of laser light, to observe the Doppler shift of scattered light from multiple directions. This enables the reconstruction of the full wind vector and the retrieval of true air speed, angle of attack, and angle of sideslip. A second instrument used tunable diode laser absorption spectroscopy, which measures an individual transition of molecular oxygen in the A band, in order to extract the static pressure from the observed collisional broadening. The techniques were implemented as airborne research instruments on the DLR’s Dassault Falcon 20 aircraft and tested in two campaigns in 2022 under different atmospheric conditions and dynamic maneuvers. We present results from these campaigns, focusing on general sensor performance, measurement rates, accuracy, and experimental challenges that need to be addressed for future applications.
- Open Access
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Instrumentation and Measurement
- Vol. 3, 1-10
Pressure Detection With Mach–Zehnder Linearized Tunable Diode-Laser Absorption Spectroscopy
Tunable diode-laser absorption spectroscopy (TDLAS) sensors have shown to be applicable to e.g. temperature and pressure measurements in gases. These parameters are indispensable in modern avionics. Even though these systems performed well in laboratory or closed environments, the harsh conditions of avionic flight introduce sources of error. To cope with these challenges, altered variants of the classical direct TDLAS may be taken into consideration. Here, we investigate the differences between an all fiber direct TDLAS and a Mach-Zehnder based amplitude modulated TDLAS variant. We are able to demonstrate the increased noise immunity of the amplitude modulated system as well as the use of the oxygen A-band for the use as an optical pressure detector.
- 6 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Instrumentation and Measurement
- Vol. 3, 1-10
Open AccessPressure Detection With Mach–Zehnder Linearized Tunable Diode-Laser Absorption Spectroscopy
Tunable diode-laser absorption spectroscopy (TDLAS) sensors have shown to be applicable to e.g. temperature and pressure measurements in gases. These parameters are indispensable in modern avionics. Even though these systems performed well in laboratory or closed environments, the harsh conditions of avionic flight introduce sources of error. To cope with these challenges, altered variants of the classical direct TDLAS may be taken into consideration. Here, we investigate the differences between an all fiber direct TDLAS and a Mach-Zehnder based amplitude modulated TDLAS variant. We are able to demonstrate the increased noise immunity of the amplitude modulated system as well as the use of the oxygen A-band for the use as an optical pressure detector.
- 12 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12939, 116-128
Impact of material and surface properties on thermo-mechanical coupling in laser-based orbit modification of space debris
The rapidly increasing amount of space debris is a critical problem of modern and future space infrastructure. Repetitively pulsed high energy lasers are frequently discussed as a technological option for the remotely based removal of multiple small space debris objects from the low Earth orbit (LEO) by recoil from laser ablation. Aiming for a realistic assessment of the concept’s efficiency in debris mitigation, awareness of thermal constraints is needed. In our study, we employ finite element analysis (FEM) of the laser ablation process regarding imparted momentum from laser-ablative recoil as well as laser-induced heat inside the target after ablation. The simulation results are underpinned by observations of velocity change and temperature increase from single pulse laser irradiation of cm-sized targets in a drop experiment in vacuum (10 ns pulse duration, 1064 nm wavelength, 60 J nominal pulse energy) from the nhelix laser of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt, Germany. Both polished and sandblasted samples of common space debris materials like aluminum, copper, steel, and titanium are employed in our analysis. Our findings suggest that exhaustive target reconnaissance is required to ensure operational safety in laser-based orbit modification regarding predictability of the modified trajectory as well as thermal constraints in target heating.
- 12 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12939, 116-128
Impact of material and surface properties on thermo-mechanical coupling in laser-based orbit modification of space debris
The rapidly increasing amount of space debris is a critical problem of modern and future space infrastructure. Repetitively pulsed high energy lasers are frequently discussed as a technological option for the remotely based removal of multiple small space debris objects from the low Earth orbit (LEO) by recoil from laser ablation. Aiming for a realistic assessment of the concept’s efficiency in debris mitigation, awareness of thermal constraints is needed. In our study, we employ finite element analysis (FEM) of the laser ablation process regarding imparted momentum from laser-ablative recoil as well as laser-induced heat inside the target after ablation. The simulation results are underpinned by observations of velocity change and temperature increase from single pulse laser irradiation of cm-sized targets in a drop experiment in vacuum (10 ns pulse duration, 1064 nm wavelength, 60 J nominal pulse energy) from the nhelix laser of the GSI Helmholtz Centre for Heavy Ion Research in Darmstadt, Germany. Both polished and sandblasted samples of common space debris materials like aluminum, copper, steel, and titanium are employed in our analysis. Our findings suggest that exhaustive target reconnaissance is required to ensure operational safety in laser-based orbit modification regarding predictability of the modified trajectory as well as thermal constraints in target heating.
- 11 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12939, 104-109
Compact chirp-free ps-pulse wedged thin-disk amplifier
Amplifying ps-laser radiation to high pulse-energies as well as a high average output power is a challenging task. In the past it was shown that thin-disk multipass amplifiers can achieve excellent properties for ultrashort laser pulses at over 1 kW of average power. Furthermore, systems combining multipass and regenerative thindisk amplifiers achieved 700 mJ of pulse energy at a repetition rate of 1000 Hz. These systems reaching such excellent properties are complex, extensive and typically need dozens of mirror-optics and the corresponding space associated with those. With the introduction of our monolithic wedged thin-disk (WTD) concept we were able to demonstrate small signal laser amplification of up to 10 (+10 dB) for cw-systems with a drastically reduced amount of mirror optics as well as space needed. By adding a redirecting mirror to introduce two multipasses in the WTD we were able to amplify a 2 ps-laser source with a small signal gain of up to 55 (+17 dB) and at 20W seed power by a factor of 5 (+7 dB) reaching up to 100W of output power.
- 11 April 2024
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12939, 104-109
Compact chirp-free ps-pulse wedged thin-disk amplifier
Amplifying ps-laser radiation to high pulse-energies as well as a high average output power is a challenging task. In the past it was shown that thin-disk multipass amplifiers can achieve excellent properties for ultrashort laser pulses at over 1 kW of average power. Furthermore, systems combining multipass and regenerative thindisk amplifiers achieved 700 mJ of pulse energy at a repetition rate of 1000 Hz. These systems reaching such excellent properties are complex, extensive and typically need dozens of mirror-optics and the corresponding space associated with those. With the introduction of our monolithic wedged thin-disk (WTD) concept we were able to demonstrate small signal laser amplification of up to 10 (+10 dB) for cw-systems with a drastically reduced amount of mirror optics as well as space needed. By adding a redirecting mirror to introduce two multipasses in the WTD we were able to amplify a 2 ps-laser source with a small signal gain of up to 55 (+17 dB) and at 20W seed power by a factor of 5 (+7 dB) reaching up to 100W of output power.
- Open Access
Modification of Space Debris Trajectories through Lasers: Dependence of Thermal and Impulse Coupling on Material and Surface Properties
Environmental pollution exists not only within our atmosphere but also in space. Space debris is a critical problem of modern and future space infrastructure. Congested orbits raise the question of spacecraft disposal. Therefore, state-of-the-art satellites come with a deorbit system in cases of low Earth orbit (LEO) and with thrusters for transferring into the graveyard orbit for geostationary and geosynchronous orbits. No practical solution is available for debris objects that stem from fragmentation events. The present study focuses on objects in LEO orbits with dimensions in the dangerous class of 1 to 10 cm. Our assumed method for the change of trajectories of space debris is laser ablation for collision avoidance or complete removal by ground-based laser systems. Thus, we executed an experimental feasibility study with focus on thermal and impulse coupling between laser and sample. Free-fall experiments with a 10 ns laser pulse at nominally 60 J and 1064 nm were conducted with GSI Darmstadt’s nhelix laser on various sample materials with different surfaces. Ablated mass, heating, and trajectory were recorded. Furthermore, we investigated the influence of the sample surface roughness on the laser-object interaction. We measured impulse coupling coefficients between 7 and 40 µNs/J and thermal coupling coefficients between 2% and 12.5% both depending on target fluence, surface roughness, and material. Ablated mass and changes in surface roughness were considered via simulation to discriminate their relevance for a multiple shot concept.
Open AccessModification of Space Debris Trajectories through Lasers: Dependence of Thermal and Impulse Coupling on Material and Surface Properties
Environmental pollution exists not only within our atmosphere but also in space. Space debris is a critical problem of modern and future space infrastructure. Congested orbits raise the question of spacecraft disposal. Therefore, state-of-the-art satellites come with a deorbit system in cases of low Earth orbit (LEO) and with thrusters for transferring into the graveyard orbit for geostationary and geosynchronous orbits. No practical solution is available for debris objects that stem from fragmentation events. The present study focuses on objects in LEO orbits with dimensions in the dangerous class of 1 to 10 cm. Our assumed method for the change of trajectories of space debris is laser ablation for collision avoidance or complete removal by ground-based laser systems. Thus, we executed an experimental feasibility study with focus on thermal and impulse coupling between laser and sample. Free-fall experiments with a 10 ns laser pulse at nominally 60 J and 1064 nm were conducted with GSI Darmstadt’s nhelix laser on various sample materials with different surfaces. Ablated mass, heating, and trajectory were recorded. Furthermore, we investigated the influence of the sample surface roughness on the laser-object interaction. We measured impulse coupling coefficients between 7 and 40 µNs/J and thermal coupling coefficients between 2% and 12.5% both depending on target fluence, surface roughness, and material. Ablated mass and changes in surface roughness were considered via simulation to discriminate their relevance for a multiple shot concept.
- 8 February 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (4) , 6356-6369
Synthetic dispersion interferometry for relative atmospheric pressure sensing
We present a modified version of the two-arm, two-color, single second harmonic generation heterodyne dispersion interferometer, as introduced by Irby et. al. [Rev. Sci. Instrum. 70, 699 (1999) ]. The amount of optical elements is reduced and digital in-phase and quadrature demodulation is used to retrieve the phase shift from a single photodetector signal. The intrinsic system noise and drift for this device are analyzed by measuring the Allan deviation. We investigate the use of this device for relative atmospheric pressure measurement. Relative pressure measurements are performed in a pressure chamber and referenced against a piezoresistive pressure transceiver to demonstrate the concept. It was found that the deviation was less than 150 Pa and an error estimation has been derived.Published by Optica Publishing Group under the terms of the Creative Commons Attribution 4.0 License. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI.
- 8 February 2023
- Published by Optica Publishing Group in Optics Express
- Vol. 31 (4) , 6356-6369
Synthetic dispersion interferometry for relative atmospheric pressure sensing
We present a modified version of the two-arm, two-color, single second harmonic generation heterodyne dispersion interferometer, as introduced by Irby et. al. [Rev. Sci. Instrum. 70, 699 (1999) ]. The amount of optical elements is reduced and digital in-phase and quadrature demodulation is used to retrieve the phase shift from a single photodetector signal. The intrinsic system noise and drift for this device are analyzed by measuring the Allan deviation. We investigate the use of this device for relative atmospheric pressure measurement. Relative pressure measurements are performed in a pressure chamber and referenced against a piezoresistive pressure transceiver to demonstrate the concept. It was found that the deviation was less than 150 Pa and an error estimation has been derived.Published by Optica Publishing Group under the terms of the Creative Commons Attribution 4.0 License. Further distribution of this work must maintain attribution to the author(s) and the published article's title, journal citation, and DOI.
- Open Access
- 1 March 2022
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 61 (03) , 039801-2
Momentum predictability and heat accumulation in laser-based space debris removal (Erratum)
This erratum corrects errors in the published paper.
- 1 March 2022
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 61 (03) , 039801-2
Open AccessMomentum predictability and heat accumulation in laser-based space debris removal (Erratum)
This erratum corrects errors in the published paper.
- Open Access
- 7 April 2021
- Published by Optica Publishing Group in OSA Continuum
- Vol. 4 (4) , 1304-1315
USB-powered technology platform for laser ablative thrust generation
Small satellites gave the opportunity to universities all over the world, allowing their students to participate in a complete satellite mission. After some years, the graduating students and the developing technologies for satellites as small as a 1 liter cube, have reached a point where a new type of space industry is developing and gaining importance. Despite all possibilities and components available for such systems, it is still a very difficult task to maneuver these satellites due to the lack of compact and efficient thruster systems. Here we demonstrate the compactification of a laser ablative thruster concept called MICROLAS. We verify the functionality of all sub components and demonstrate ablation under vacuum conditions.
- 7 April 2021
- Published by Optica Publishing Group in OSA Continuum
- Vol. 4 (4) , 1304-1315
Open AccessUSB-powered technology platform for laser ablative thrust generation
Small satellites gave the opportunity to universities all over the world, allowing their students to participate in a complete satellite mission. After some years, the graduating students and the developing technologies for satellites as small as a 1 liter cube, have reached a point where a new type of space industry is developing and gaining importance. Despite all possibilities and components available for such systems, it is still a very difficult task to maneuver these satellites due to the lack of compact and efficient thruster systems. Here we demonstrate the compactification of a laser ablative thruster concept called MICROLAS. We verify the functionality of all sub components and demonstrate ablation under vacuum conditions.
- Open Access
- 12 October 2020
- Published by Optica Publishing Group in Optica
- Vol. 7 (10) , 1409-1414
Monolithic thin-disk laser and amplifier concept
Thin-disk lasers are indispensable in photonics research as well as in a multitude of industrial applications. They represent a unique class of laser and amplifier architecture that provides kW output power with excellent properties concerning beam quality, long-term stability, thermal management, and power scalability. For many applications, a reduced complexity of the laser and its size would be highly beneficial. The necessary multipass transitions in thin-disk lasers and amplifiers typically require sophisticated multi-mirror arrangements. Here, we present a monolithic version of the pump concept for thin-disk lasers and amplifiers, where the thin disk is replaced by a thin, wedged gain medium acting as a wedged optical trap. The wedge is coated in a peculiar manner in order to allow for efficient in- and out-coupling of the pump and laser radiation from the wedge. This concept transfers the complexity of the multi-mirror optics into the thin disk itself in a monolithic fashion. With this concept, we achieved 890 W of CW output power, 59% slope efficiency, optical-to-optical efficiency of 50%, and a gain factor greater than 10 for small signals. This demonstrates that this new concept is capable of reaching the kW power regime with minimum complexity and size.
- 12 October 2020
- Published by Optica Publishing Group in Optica
- Vol. 7 (10) , 1409-1414
Open AccessMonolithic thin-disk laser and amplifier concept
Thin-disk lasers are indispensable in photonics research as well as in a multitude of industrial applications. They represent a unique class of laser and amplifier architecture that provides kW output power with excellent properties concerning beam quality, long-term stability, thermal management, and power scalability. For many applications, a reduced complexity of the laser and its size would be highly beneficial. The necessary multipass transitions in thin-disk lasers and amplifiers typically require sophisticated multi-mirror arrangements. Here, we present a monolithic version of the pump concept for thin-disk lasers and amplifiers, where the thin disk is replaced by a thin, wedged gain medium acting as a wedged optical trap. The wedge is coated in a peculiar manner in order to allow for efficient in- and out-coupling of the pump and laser radiation from the wedge. This concept transfers the complexity of the multi-mirror optics into the thin disk itself in a monolithic fashion. With this concept, we achieved 890 W of CW output power, 59% slope efficiency, optical-to-optical efficiency of 50%, and a gain factor greater than 10 for small signals. This demonstrates that this new concept is capable of reaching the kW power regime with minimum complexity and size.