Shu-Fen Hu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Shu-Fen Hu has a total of 170 co-authors. Here are the top co-authors by number of shared publications:
- Ru-Shi Liu
Department of Chemistry National Taiwan University Taipei Taiwan
65 shared publications - Chih-Jung Chen
Graduate School of Advanced Technology National Taiwan University Taipei Taiwan
19 shared publications Ho Chang
Department of Mechanical Engineering and Graduate Institute of Manufacturing Technology, National Taipei University of Technology, Taipei 106, Taiwan
14 shared publications- Anirudha Jena
Department of Chemistry, National Taiwan University, Taipei 106, Taiwan
12 shared publications Zizheng Tong
Department of Chemistry, National Taiwan University, Taipei 106, Taiwan
11 shared publicationsKevin Iputera
Department of Chemistry and Advanced Research Center for Green Materials Science and Technology, National Taiwan University, Taipei 106, Taiwan
8 shared publications
Latest Publications
- 9 February 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16  (7) , 8783-8790
Homogeneous Catalytic Process of a Heterogeneous Ru Catalyst in LiâO2 via X-ray Nanodiffraction Observation
In recent years, lithium oxygen batteries (Li-O2) have received considerable research attention due to their extremely high energy density. However, the poor conductivity and ion conductivity of the discharge product lithium peroxide (Li2O2) result in a high charging overpotential, poor cycling stability, and low charging rate. Therefore, studying and improving catalysts is a top priority. This study focuses on the commonly used heterogeneous catalyst ruthenium (Ru). The local distribution of this catalyst is controlled by using sputtering technology. Moreover, X-ray nanodiffraction is applied to observe the relationship between the decomposition of Li2O2 and the local distribution of Ru. Results show that Li2O2 decomposes homogeneously in liquid systems and heterogeneously in solid-state systems. This study finds that the catalytic effect of Ru is related to electrolyte decomposition and that its soluble byproducts act as electron acceptors or redox mediators, effectively reducing charging overpotential but also shortening the cycle life.
- 9 February 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16  (7) , 8783-8790
Homogeneous Catalytic Process of a Heterogeneous Ru Catalyst in LiâO2 via X-ray Nanodiffraction Observation
In recent years, lithium oxygen batteries (Li-O2) have received considerable research attention due to their extremely high energy density. However, the poor conductivity and ion conductivity of the discharge product lithium peroxide (Li2O2) result in a high charging overpotential, poor cycling stability, and low charging rate. Therefore, studying and improving catalysts is a top priority. This study focuses on the commonly used heterogeneous catalyst ruthenium (Ru). The local distribution of this catalyst is controlled by using sputtering technology. Moreover, X-ray nanodiffraction is applied to observe the relationship between the decomposition of Li2O2 and the local distribution of Ru. Results show that Li2O2 decomposes homogeneously in liquid systems and heterogeneously in solid-state systems. This study finds that the catalytic effect of Ru is related to electrolyte decomposition and that its soluble byproducts act as electron acceptors or redox mediators, effectively reducing charging overpotential but also shortening the cycle life.
- 28 November 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (49) , 57828-57834
In Situ and Low-Cost Improvement of the Lithium Anode Interface in Garnet-Type Solid-State Electrolytes
In recent years, the development of electric vehicles and environmental concerns have made necessary improvements in the energy density and safety of lithium-ion batteries. Therefore, the development of all-solid-state lithium-ion batteries (ASSLIBs) has become imperative. One advantage of ASSLIBs is their potential for downsizing with the use of lithium metal as the anode. However, in this study, a garnet-type solid electrolyte (Li6.75La3Zr1.75Ta0.25O12) was used, which has low reactivity with lithium metal. Thus, interface modification using CaCl2 was employed to form a Li-Ca-Cl composite anode. The interfacial resistance was remarkably reduced to 7 Ω cm2, and the symmetric cell exhibited stable cycling for 1200 h at room temperature and a current density of 0.1 mA cm-2. The voltage ranged from ±15 to ±16 mV. The full cell demonstrated a high initial discharge capacity of 149.2 mA h g-1 and a Coulombic efficiency of 98.0% while maintaining a discharge capacity retention of 91.3% after 100 cycles. These findings lay a solid foundation for future commercial applications as interface modification was achieved through a simple spin-coating process using low-cost CaCl2 (0.7 USD g-1).
- 28 November 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (49) , 57828-57834
In Situ and Low-Cost Improvement of the Lithium Anode Interface in Garnet-Type Solid-State Electrolytes
In recent years, the development of electric vehicles and environmental concerns have made necessary improvements in the energy density and safety of lithium-ion batteries. Therefore, the development of all-solid-state lithium-ion batteries (ASSLIBs) has become imperative. One advantage of ASSLIBs is their potential for downsizing with the use of lithium metal as the anode. However, in this study, a garnet-type solid electrolyte (Li6.75La3Zr1.75Ta0.25O12) was used, which has low reactivity with lithium metal. Thus, interface modification using CaCl2 was employed to form a Li-Ca-Cl composite anode. The interfacial resistance was remarkably reduced to 7 Ω cm2, and the symmetric cell exhibited stable cycling for 1200 h at room temperature and a current density of 0.1 mA cm-2. The voltage ranged from ±15 to ±16 mV. The full cell demonstrated a high initial discharge capacity of 149.2 mA h g-1 and a Coulombic efficiency of 98.0% while maintaining a discharge capacity retention of 91.3% after 100 cycles. These findings lay a solid foundation for future commercial applications as interface modification was achieved through a simple spin-coating process using low-cost CaCl2 (0.7 USD g-1).
- 8 September 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (37) , 44413-44421
Synergistic Effect of the Anode Interface of Garnet-Type All-Solid-State Batteries
Next-generation lithium-ion batteries must have high energy density and safety, making the development of allsolid-state batteries imperative. One of the biggest advantages of an all-solid-state lithium-ion battery (ASSLIB) is that its alloy uses lithium metal as an anode while ignoring its flammability and other d a n g e r s. H e r e i n, h i g h - c o n d u c t i v i t y g a r n e t - t y p e Li6.75La3Zr1.75Ta0.25O12 (LLZTO) was chosen as the solid electrolyte part of an all-solid-state battery. A composite anode was formed by melting Li and MXene-MAX together, reducing the interface impedance from 566 to 55 Omega cm(2). The Li-MXene| LLZTO|LFP full battery displayed a high initial discharge capacity of 163.0 mAh g(-1) and a Coulombic efficiency of 97.0% and maintained 90.2% of its discharge capacity over 100 cycles, but it did not maintain a good overpotential. Therefore, the synergistic effect of Li-MXene-Pt will highly improve the performance of the full battery because of its high initial discharge capacity of 150.0 mAh g(-1) and Coulombic efficiency of 95.5%, discharge capacity maintained at 93.3% over 100 cycles, and low overpotential of 0.04 V.
- 8 September 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (37) , 44413-44421
Synergistic Effect of the Anode Interface of Garnet-Type All-Solid-State Batteries
Next-generation lithium-ion batteries must have high energy density and safety, making the development of allsolid-state batteries imperative. One of the biggest advantages of an all-solid-state lithium-ion battery (ASSLIB) is that its alloy uses lithium metal as an anode while ignoring its flammability and other d a n g e r s. H e r e i n, h i g h - c o n d u c t i v i t y g a r n e t - t y p e Li6.75La3Zr1.75Ta0.25O12 (LLZTO) was chosen as the solid electrolyte part of an all-solid-state battery. A composite anode was formed by melting Li and MXene-MAX together, reducing the interface impedance from 566 to 55 Omega cm(2). The Li-MXene| LLZTO|LFP full battery displayed a high initial discharge capacity of 163.0 mAh g(-1) and a Coulombic efficiency of 97.0% and maintained 90.2% of its discharge capacity over 100 cycles, but it did not maintain a good overpotential. Therefore, the synergistic effect of Li-MXene-Pt will highly improve the performance of the full battery because of its high initial discharge capacity of 150.0 mAh g(-1) and Coulombic efficiency of 95.5%, discharge capacity maintained at 93.3% over 100 cycles, and low overpotential of 0.04 V.
- 28 July 2023
- Published by Wiley in ChemSusChem
- Vol. 16  (19) , e202300504
Robust and Intimate Interface Enabled by Silicon Carbide as an Additive to Anodes for Lithium Metal SolidâState Batteries
Garnetâtype solidâstate electrolytes are among the most reassuring candidates for the development of solidâstate lithium metal batteries (SSLMB) because of their wide electrochemical stability window and chemical feasibility with lithium. However, issues such as poor physical contact with Li metal tend to limit their practical applications. These problems were addressed using ÎČâSiC as an additive to the Li anode, resulting in improved wettability over Li6.75La3Zr1.75Ta0.25O12 (LLZTO) and establishing an improved interfacial contact. At the LiâSiC|LLZTO interface, intimacy was induced by a lithiophilic Li4SiO4 phase, whereas robustness was attained through the hard SiC phase. The optimized LiâSiC|LLZTO|LiâSiC symmetric cell displayed a low interfacial impedance of 10 Ω cm2 and superior cycling stability at varying current densities up to 5800 h. Moreover, the modified interface could achieve a high critical current density of 4.6 mA cmâ2 at room temperature and cycling stability of 1000 h at 3.5 mA cmâ2. The use of mechanically superior materials such as SiC as additives for the preparation of a composite anode may serve as a new strategy for robust garnetâbased SSLMB.
- 28 July 2023
- Published by Wiley in ChemSusChem
- Vol. 16  (19) , e202300504
Robust and Intimate Interface Enabled by Silicon Carbide as an Additive to Anodes for Lithium Metal SolidâState Batteries
Garnetâtype solidâstate electrolytes are among the most reassuring candidates for the development of solidâstate lithium metal batteries (SSLMB) because of their wide electrochemical stability window and chemical feasibility with lithium. However, issues such as poor physical contact with Li metal tend to limit their practical applications. These problems were addressed using ÎČâSiC as an additive to the Li anode, resulting in improved wettability over Li6.75La3Zr1.75Ta0.25O12 (LLZTO) and establishing an improved interfacial contact. At the LiâSiC|LLZTO interface, intimacy was induced by a lithiophilic Li4SiO4 phase, whereas robustness was attained through the hard SiC phase. The optimized LiâSiC|LLZTO|LiâSiC symmetric cell displayed a low interfacial impedance of 10 Ω cm2 and superior cycling stability at varying current densities up to 5800 h. Moreover, the modified interface could achieve a high critical current density of 4.6 mA cmâ2 at room temperature and cycling stability of 1000 h at 3.5 mA cmâ2. The use of mechanically superior materials such as SiC as additives for the preparation of a composite anode may serve as a new strategy for robust garnetâbased SSLMB.
- 13 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (7) , 9675-9684
Battery Performance Amelioration by Introducing a Conducive Mixed Electrolyte in Rechargeable MgâO2 Batteries
With magnesium being a cost-effective anode metal compared to the other conventional Li-based anodes in the energy market, it could be a capable source of energy storage. However, Mg-O2 batteries have struggled its way to overcome the poor cycling stability and sluggish reaction kinetics. Therefore, Ru metallic nanoparticles on carbon nanotubes (CNTs) were introduced as a cathode for Mg-O2 batteries, which are known for their inherent electronic properties, large surface area, and increased crystallinity to favor remarkable oxygen reduction reactions and oxygen evolution reactions (ORR and OER). Also, we deployed a first-of-its-kind, conducive mixed electrolyte (CME) (2 M Mg(NO3)2:1 M Mg(TFSI)2/diglyme). Hence, this synergistic incorporation of CME-based Ru/CNT Mg-O2 batteries could unleash long cycle life with low overpotential, excellent reversibility, and high ionic conductivity and also reduces the intrinsic corrosion behavior of Mg anodes. Correspondingly, this novel amalgamation of CME with Ru/CNT cathode has displayed superior cyclic stability of 65 cycles and a maximum discharge potential of 25 793 mAh g-1 with a small overvoltage plateau of 1.4 V, noticeably subjugating the findings of conventional single electrolyte (CSE) (1 M Mg(TFSI)2/diglyme). This CME-based Ru/CNT Mg-O2 battery design could have a significant outcome as a future battery technology.
- 13 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (7) , 9675-9684
Battery Performance Amelioration by Introducing a Conducive Mixed Electrolyte in Rechargeable MgâO2 Batteries
With magnesium being a cost-effective anode metal compared to the other conventional Li-based anodes in the energy market, it could be a capable source of energy storage. However, Mg-O2 batteries have struggled its way to overcome the poor cycling stability and sluggish reaction kinetics. Therefore, Ru metallic nanoparticles on carbon nanotubes (CNTs) were introduced as a cathode for Mg-O2 batteries, which are known for their inherent electronic properties, large surface area, and increased crystallinity to favor remarkable oxygen reduction reactions and oxygen evolution reactions (ORR and OER). Also, we deployed a first-of-its-kind, conducive mixed electrolyte (CME) (2 M Mg(NO3)2:1 M Mg(TFSI)2/diglyme). Hence, this synergistic incorporation of CME-based Ru/CNT Mg-O2 batteries could unleash long cycle life with low overpotential, excellent reversibility, and high ionic conductivity and also reduces the intrinsic corrosion behavior of Mg anodes. Correspondingly, this novel amalgamation of CME with Ru/CNT cathode has displayed superior cyclic stability of 65 cycles and a maximum discharge potential of 25 793 mAh g-1 with a small overvoltage plateau of 1.4 V, noticeably subjugating the findings of conventional single electrolyte (CSE) (1 M Mg(TFSI)2/diglyme). This CME-based Ru/CNT Mg-O2 battery design could have a significant outcome as a future battery technology.
- 9 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (7) , 10283-10291
Spontaneous In Situ Formation of Lithium Metal Nitride in the Interface of Garnet-Type Solid-State Electrolyte by Tuning of Molten Lithium
All-solid-state lithium-ion batteries (ASSLIBs) have attracted much attention owing to their high energy density and safety and are known as the most promising next-generation LIBs. The biggest advantage of ASSLIBs is that it can use lithium metal as the anode without any safety concerns. This study used a high-conductivity garnet-type solid electrolyte (Li6.75La3Zr1.75Ta0.25O12, LLZTO) and Li-Ga-N composite anode synthesized by mixing melted Li with GaN. The interfacial resistance was reduced from 589 to 21 Ω cm2, the symmetry cell was stably cycled for 1000 h at a current density of 0.1 mA cm-2 at room temperature, and the voltage range only changed from ±30 to ±40 mV. The full cell of Li-Ga-N|LLZTO|LFP exhibited a high first-cycle discharge capacity of 152.2 mAh g-1 and Coulombic efficiency of 96.5% and still maintained a discharge capacity retention of 91.2% after 100 cycles. This study also demonstrated that Li-Ga-N had been shown as two layers. Li3N shows more inclined to be closer to the LLZTO side. This method can help researchers understand what interface improvements can occur to enhance the performance of all-solid-state batteries in the future.
- 9 February 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15  (7) , 10283-10291
Spontaneous In Situ Formation of Lithium Metal Nitride in the Interface of Garnet-Type Solid-State Electrolyte by Tuning of Molten Lithium
All-solid-state lithium-ion batteries (ASSLIBs) have attracted much attention owing to their high energy density and safety and are known as the most promising next-generation LIBs. The biggest advantage of ASSLIBs is that it can use lithium metal as the anode without any safety concerns. This study used a high-conductivity garnet-type solid electrolyte (Li6.75La3Zr1.75Ta0.25O12, LLZTO) and Li-Ga-N composite anode synthesized by mixing melted Li with GaN. The interfacial resistance was reduced from 589 to 21 Ω cm2, the symmetry cell was stably cycled for 1000 h at a current density of 0.1 mA cm-2 at room temperature, and the voltage range only changed from ±30 to ±40 mV. The full cell of Li-Ga-N|LLZTO|LFP exhibited a high first-cycle discharge capacity of 152.2 mAh g-1 and Coulombic efficiency of 96.5% and still maintained a discharge capacity retention of 91.2% after 100 cycles. This study also demonstrated that Li-Ga-N had been shown as two layers. Li3N shows more inclined to be closer to the LLZTO side. This method can help researchers understand what interface improvements can occur to enhance the performance of all-solid-state batteries in the future.
- 2 December 2022
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24  (24) , 9755-9762
H2O wash: a simple method toward eliminating discharge products and regenerating cathodes of LiâO2 batteries
LiâO2 batteries have been the focus of research for decades. However, there are only few studies on the recycle of LiâO2 batteries. Herein, we provide a facile H2O wash method which could revive air cathodes with ease.
- 2 December 2022
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24  (24) , 9755-9762
H2O wash: a simple method toward eliminating discharge products and regenerating cathodes of LiâO2 batteries
LiâO2 batteries have been the focus of research for decades. However, there are only few studies on the recycle of LiâO2 batteries. Herein, we provide a facile H2O wash method which could revive air cathodes with ease.
- 10 November 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5  (11) , 14280-14289
All-Solid-State NaâO2 Batteries with Long Cycle Performance
- 10 November 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5  (11) , 14280-14289
All-Solid-State NaâO2 Batteries with Long Cycle Performance
- 7 September 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5  (9) , 11694-11704
Degradation of a Li1.5Al0.5Ge1.5(PO4)3-Based Solid-State Li-Metal Battery: Corrosion of Li1.5Al0.5Ge1.5(PO4)3 against the Li-Metal Anode
- 7 September 2022
- Published by American Chemical Society (ACS) in ACS Applied Energy Materials
- Vol. 5  (9) , 11694-11704
Degradation of a Li1.5Al0.5Ge1.5(PO4)3-Based Solid-State Li-Metal Battery: Corrosion of Li1.5Al0.5Ge1.5(PO4)3 against the Li-Metal Anode
- 26 August 2022
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 14  (35) , 39896-39906
Defect Mediated Improvements in the Photoelectrochemical Activity of MoS2/SnS2 Ultrathin Sheets on Si Photocathode for Hydrogen Evolution
Solar-driven water electrolysis to produce hydrogen is one of the clean energy options for the current energy-related challenges. Si as a photocathode exhibits a large overpotential due to the slow hydrogen evolution reaction (HER) kinetics and hence needs to be modified with a cocatalyst layer. MoS2 is a poor HER cocatalyst due to its inert basal plane. Activation of the MoS2 basal plane will facilitate HER kinetics. In this study, we have incorporated SnS2 into MoS2 ultrathin sheets to induce defect formation and phase transformation. MoS2/SnS2 composite ultrathin sheets with a Sn2+ state create a large number of S vacancies on the basal sites. The optimized defect-rich MoS2/SnS2 ultrathin sheets decorated on surface-modified Si micro pyramids as photocathodes show a current density of -23.8 mA/cm2 at 0 V with an onset potential of 0.23 V under acidic conditions, which is higher than that of the pristine MoS2. The incorporation of SnS2 into 2H-MoS2 ultrathin sheets not only induces a phase but also can alter the local atomic arrangement, which in turn is verified by their magnetic response. The diamagnetic SnS2 phase causes a decrease in symmetry and an increase in magnetic anisotropy of the Mo3+ ions.
- 26 August 2022
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 14  (35) , 39896-39906
Defect Mediated Improvements in the Photoelectrochemical Activity of MoS2/SnS2 Ultrathin Sheets on Si Photocathode for Hydrogen Evolution
Solar-driven water electrolysis to produce hydrogen is one of the clean energy options for the current energy-related challenges. Si as a photocathode exhibits a large overpotential due to the slow hydrogen evolution reaction (HER) kinetics and hence needs to be modified with a cocatalyst layer. MoS2 is a poor HER cocatalyst due to its inert basal plane. Activation of the MoS2 basal plane will facilitate HER kinetics. In this study, we have incorporated SnS2 into MoS2 ultrathin sheets to induce defect formation and phase transformation. MoS2/SnS2 composite ultrathin sheets with a Sn2+ state create a large number of S vacancies on the basal sites. The optimized defect-rich MoS2/SnS2 ultrathin sheets decorated on surface-modified Si micro pyramids as photocathodes show a current density of -23.8 mA/cm2 at 0 V with an onset potential of 0.23 V under acidic conditions, which is higher than that of the pristine MoS2. The incorporation of SnS2 into 2H-MoS2 ultrathin sheets not only induces a phase but also can alter the local atomic arrangement, which in turn is verified by their magnetic response. The diamagnetic SnS2 phase causes a decrease in symmetry and an increase in magnetic anisotropy of the Mo3+ ions.