Nadia Saidi-Amroun
Nadia Saidi-Amroun has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
M. Saidi
Material Physics Laboratory, Physics Faculty, University of Sciences and Technology (USTHB), BP 32 El-Alia, Bab-Ezzouar, Algiers, Algeria
18 shared publicationsM. Bendaoud
Material Physics Laboratory, Physics Faculty, University of Science and Technology (USTHB) , Algiers , Algeria
11 shared publicationsMohamed Saidi
Material Physics Laboratory, University of Sciences and Technology (USTHB), Algiers, Algeria
7 shared publications- S. Berdous
Material Physics Laboratory, Physics Faculty, University of Science and Technology (USTHB) , Algiers , Algeria ; High National School of Veterinary (ENSV) , Algiers , Algeria
6 shared publications S. Berdous
5 shared publications- Gilbert Teyssedre
LAPLACE, Université de Toulouse, CNRS, INPT, UPS, Toulouse, France
4 shared publications
Latest Publications
- 31 January 2023
- Published by Springer Nature in Journal of Polymer Research
- Vol. 30 (2) , 1-11
Correlation between chemical, thermal and dielectric properties of gamma-irradiated PTFE thin films
- 31 January 2023
- Published by Springer Nature in Journal of Polymer Research
- Vol. 30 (2) , 1-11
Correlation between chemical, thermal and dielectric properties of gamma-irradiated PTFE thin films
- Open Access
- 1 March 2019
- Published by Institution of Engineering and Technology (IET) in IET Science, Measurement & Technology
- Vol. 13 (2) , 272-278
Effect of electrodes material on transient currents in dielectric liquid
In this study, results of polarisation and depolarisation currents measured on an insulating liquid are presented. The goal is to contribute to a better understanding of mechanisms occurring at the metal–liquid contact. Electrodes of different metallic nature are associated with the same mineral oil, the metal / liquid / metal structure is submitted to DC voltages and the transient current is recorded with a high sensitive electrometer. The current versus time feature shows that the conduction process is in good compliance with the metal work function rather than with its electric conductivity. The current versus field characteristics indicate a predominance of the ohmic behaviour for the low fields. The space charge limited conduction regime appears as soon as the electrical constraint exceeds ∼1 MV/m, which corresponds to 10% of the breakdown voltage. Schottky injection is suspected to occur from the metal into the liquid since the applied fields are uniform and non‐extremely intensified.
- 1 March 2019
- Published by Institution of Engineering and Technology (IET) in IET Science, Measurement & Technology
- Vol. 13 (2) , 272-278
Open AccessEffect of electrodes material on transient currents in dielectric liquid
In this study, results of polarisation and depolarisation currents measured on an insulating liquid are presented. The goal is to contribute to a better understanding of mechanisms occurring at the metal–liquid contact. Electrodes of different metallic nature are associated with the same mineral oil, the metal / liquid / metal structure is submitted to DC voltages and the transient current is recorded with a high sensitive electrometer. The current versus time feature shows that the conduction process is in good compliance with the metal work function rather than with its electric conductivity. The current versus field characteristics indicate a predominance of the ohmic behaviour for the low fields. The space charge limited conduction regime appears as soon as the electrical constraint exceeds ∼1 MV/m, which corresponds to 10% of the breakdown voltage. Schottky injection is suspected to occur from the metal into the liquid since the applied fields are uniform and non‐extremely intensified.
- Open Access
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 430-433
Analysis of the Gamma Irradiation Effect on PTFE Films by FTIR and DSC
Dielectric materials can be used in radiative environment that is why it is of major importance to determine their properties modifications with time. In this paper we focus our attention on PolyTetraFluoroEthylene (PTFE) films submitted to gamma radiations. We investigate the FTIR spectra and show that after exposure to Co60the crystallinity of the material is increasing. This result is confirmed by Differential Scanning Calorimetry (DSC) analysis. Some space charge distribution profiles obtained by the Pulse Electro Acoustic (PEA) method show that the irradiation favours the drift of injected charges toward the bulk. Obviously the dose of radiation must be carefully chosen in order to be able to perform electrical measurements. Indeed, we observed that if the radiation dose is too high the sample becomes fragile and most of the characterisation tools cannot be used.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 430-433
Open AccessAnalysis of the Gamma Irradiation Effect on PTFE Films by FTIR and DSC
Dielectric materials can be used in radiative environment that is why it is of major importance to determine their properties modifications with time. In this paper we focus our attention on PolyTetraFluoroEthylene (PTFE) films submitted to gamma radiations. We investigate the FTIR spectra and show that after exposure to Co60the crystallinity of the material is increasing. This result is confirmed by Differential Scanning Calorimetry (DSC) analysis. Some space charge distribution profiles obtained by the Pulse Electro Acoustic (PEA) method show that the irradiation favours the drift of injected charges toward the bulk. Obviously the dose of radiation must be carefully chosen in order to be able to perform electrical measurements. Indeed, we observed that if the radiation dose is too high the sample becomes fragile and most of the characterisation tools cannot be used.
- Open Access
- 1 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Dynamic of Space Charge in Electron-Beam Irradiated Cross-Linked PolyEthylene
The electrical properties of Crosslinked PolyEthylene -XLPE- material have been studied for many years as it is used for cable applications. In this work, XLPE peelings, previously submitted to thermal ageing are investigated under electronic irradiation. FTIR spectra did not reveal specific thermal ageing signatures. The space charge distribution has been analyzed by Pulsed Electro-Acoustic method during and after application of a DC field. The space charge profiles appear to be very dependent on the electron beam energy that determines the electron penetration depth and irradiated volume. Most of the space charge features appear linked to charge redistribution in the bulk following irradiation.
- 1 July 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Open AccessDynamic of Space Charge in Electron-Beam Irradiated Cross-Linked PolyEthylene
The electrical properties of Crosslinked PolyEthylene -XLPE- material have been studied for many years as it is used for cable applications. In this work, XLPE peelings, previously submitted to thermal ageing are investigated under electronic irradiation. FTIR spectra did not reveal specific thermal ageing signatures. The space charge distribution has been analyzed by Pulsed Electro-Acoustic method during and after application of a DC field. The space charge profiles appear to be very dependent on the electron beam energy that determines the electron penetration depth and irradiated volume. Most of the space charge features appear linked to charge redistribution in the bulk following irradiation.
- Open Access
- 1 July 2017
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 12 (7) , 478-481
Oxidative degradation and morphological properties of gamma‐irradiated isotactic polypropylene films
Isotactic polypropylene (iPP) films of 25 μm thickness were subjected to gamma‐ray irradiation for different doses (30, 60, 90 and 100 kGy) at ambient atmosphere and both molecular modifications and surface properties have been investigated by Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM), respectively. The occurrence of the oxidation process is identified and quantified by the FTIR. In addition, it is found that the carbonyl index increases with the absorbed dose which confirms that the irradiation process induces the diffusion of the oxygen into the iPP matrix. The AFM image (for virgin and higher dose irradiated samples) showed a dramatic change in the surface topography. The gamma radiation induces the formation of the nanostructured iPP surface. The roughness of the polymer surface, measured by AFM, increases after gamma irradiation. These results revealed that the oxidative degradation may be correlated with the morphological properties.
- 1 July 2017
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 12 (7) , 478-481
Open AccessOxidative degradation and morphological properties of gamma‐irradiated isotactic polypropylene films
Isotactic polypropylene (iPP) films of 25 μm thickness were subjected to gamma‐ray irradiation for different doses (30, 60, 90 and 100 kGy) at ambient atmosphere and both molecular modifications and surface properties have been investigated by Fourier transform infrared spectroscopy (FTIR) and atomic force microscopy (AFM), respectively. The occurrence of the oxidation process is identified and quantified by the FTIR. In addition, it is found that the carbonyl index increases with the absorbed dose which confirms that the irradiation process induces the diffusion of the oxygen into the iPP matrix. The AFM image (for virgin and higher dose irradiated samples) showed a dramatic change in the surface topography. The gamma radiation induces the formation of the nanostructured iPP surface. The roughness of the polymer surface, measured by AFM, increases after gamma irradiation. These results revealed that the oxidative degradation may be correlated with the morphological properties.
- Open Access
- 1 November 2016
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 11 (11) , 734-737
Effect of annealing temperatures on the turn‐on voltage of organic Schottky diode based on DPP(BTFu) 2
The electrical properties of diketopyrrolopyrrole ethyl‐hexylated (DPP(TBFu) 2 ) thin film sandwich structure of the ITO/DPP(TBFu) 2 /Al configuration for different annealing temperatures ranging from 40 to 130°C is investigated. The current–voltage characteristics showed an excellent rectifying behaviour of the device, and from which the diode parameters were extracted. It is found that all parameters remain constant upon annealing temperatures, with the exception of the turn‐on voltage. An increase of the turn‐on voltage from an initial value of 1.6–2.08 V is noticed starting from 70 to 100°C, respectively. This fact is attributed to the effect of residual solvent induced defect states that may act as free carriers. Defect states density for the non‐annealed and annealed device at 130°C derived from capacitance–voltage measurements is found to correlate well with the turn‐on voltage. It is found that annealing the device at 130°C results in a smaller concentration of defect states. In addition, it is also found that the annealing process produces the flat band voltage drop, which has a direct impact on the turn‐on voltage.
- 1 November 2016
- Published by Institution of Engineering and Technology (IET) in Micro & Nano Letters
- Vol. 11 (11) , 734-737
Open AccessEffect of annealing temperatures on the turn‐on voltage of organic Schottky diode based on DPP(BTFu) 2
The electrical properties of diketopyrrolopyrrole ethyl‐hexylated (DPP(TBFu) 2 ) thin film sandwich structure of the ITO/DPP(TBFu) 2 /Al configuration for different annealing temperatures ranging from 40 to 130°C is investigated. The current–voltage characteristics showed an excellent rectifying behaviour of the device, and from which the diode parameters were extracted. It is found that all parameters remain constant upon annealing temperatures, with the exception of the turn‐on voltage. An increase of the turn‐on voltage from an initial value of 1.6–2.08 V is noticed starting from 70 to 100°C, respectively. This fact is attributed to the effect of residual solvent induced defect states that may act as free carriers. Defect states density for the non‐annealed and annealed device at 130°C derived from capacitance–voltage measurements is found to correlate well with the turn‐on voltage. It is found that annealing the device at 130°C results in a smaller concentration of defect states. In addition, it is also found that the annealing process produces the flat band voltage drop, which has a direct impact on the turn‐on voltage.
- 23 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 561-564
The combined effect of gamma and e-beam irradiation on the electrical properties of polyethylene Terephthalate
The combined effects of two kinds of irradiation, being gamma and electron-beam, on the PET electrical conductivity are investigated. Gamma ray produces homogeneous irradiation in the material bulk whereas in e-beam with moderate energy (20keV), energy and primary electrons are deposited near the surface. The study is focused on the comparison between the gamma irradiated films and those successively irradiated using gamma and electron sources. 25 μm-thick films were first irradiated in air at room temperature by means of a 60Co gamma source at different absorbed doses (0.1 to 2MGy); thereafter exposed during 5 min to a 20 keV electron-beam with 1 nA/cm2 flux. Transient charging current measurements were performed in the DC field range 40-160 MV/m, at ambient temperature (25°C). The results show that the current increases substantially with the gamma dose. For all irradiated samples, the current-voltage characteristics exhibit a power law Vn, with n greater than two (3 - 5), which could be related to space charge limited conduction process. The variation of the current with the dose is linear for the gamma irradiated samples and exponential on the combined gamma and electron irradiated ones. It was concluded that the electron irradiation tends to attenuate the previous irradiation effects at low gamma doses, whereas it accentuates it at high doses. The change in current-time characteristics and the variation of the exponent n with dose are also discussed.
- 23 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 561-564
The combined effect of gamma and e-beam irradiation on the electrical properties of polyethylene Terephthalate
The combined effects of two kinds of irradiation, being gamma and electron-beam, on the PET electrical conductivity are investigated. Gamma ray produces homogeneous irradiation in the material bulk whereas in e-beam with moderate energy (20keV), energy and primary electrons are deposited near the surface. The study is focused on the comparison between the gamma irradiated films and those successively irradiated using gamma and electron sources. 25 μm-thick films were first irradiated in air at room temperature by means of a 60Co gamma source at different absorbed doses (0.1 to 2MGy); thereafter exposed during 5 min to a 20 keV electron-beam with 1 nA/cm2 flux. Transient charging current measurements were performed in the DC field range 40-160 MV/m, at ambient temperature (25°C). The results show that the current increases substantially with the gamma dose. For all irradiated samples, the current-voltage characteristics exhibit a power law Vn, with n greater than two (3 - 5), which could be related to space charge limited conduction process. The variation of the current with the dose is linear for the gamma irradiated samples and exponential on the combined gamma and electron irradiated ones. It was concluded that the electron irradiation tends to attenuate the previous irradiation effects at low gamma doses, whereas it accentuates it at high doses. The change in current-time characteristics and the variation of the exponent n with dose are also discussed.
- 7 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 23 (1) , 573-585
Space charge modeling in polymers: review of external applied constraints effects
The purpose of this work is to describe, with numerical simulation, the space charge behavior in polymeric materials. Particular intent is accorded to the variation of the thermo-electrical constraints. The simulation is performed for a range of the electric field from 10 to 110 MV/m and the space charge behavior was described at various temperatures: 0, 27, 60 and 100 ° C. In general, the numerical results show a predominance of the temperature effect, vs. the electric field, on the space charge behavior. The dynamic of the electrical charges is different under 100 ° C, a forehead is observed on their distribution in the sample. Strong electric field enhancements are remarked in the dielectric, they exceed 38% of the applied field under 100 ° C. Only 1.3% of augmentations are observed under room temperature even with higher applied field of 110 MV/m. Both experimental and theoretical Current-Field characteristics, plotted in log-log scale, show linear behavior with slopes greater than one. The different values of slope indicate space charge limited conduction; a change is remarked at 40 MV/m which can defines the beginning of the high fields regime in the case of the studied polymer (Polyethylene Naphthalate).
- 7 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Dielectrics and Electrical Insulation
- Vol. 23 (1) , 573-585
Space charge modeling in polymers: review of external applied constraints effects
The purpose of this work is to describe, with numerical simulation, the space charge behavior in polymeric materials. Particular intent is accorded to the variation of the thermo-electrical constraints. The simulation is performed for a range of the electric field from 10 to 110 MV/m and the space charge behavior was described at various temperatures: 0, 27, 60 and 100 ° C. In general, the numerical results show a predominance of the temperature effect, vs. the electric field, on the space charge behavior. The dynamic of the electrical charges is different under 100 ° C, a forehead is observed on their distribution in the sample. Strong electric field enhancements are remarked in the dielectric, they exceed 38% of the applied field under 100 ° C. Only 1.3% of augmentations are observed under room temperature even with higher applied field of 110 MV/m. Both experimental and theoretical Current-Field characteristics, plotted in log-log scale, show linear behavior with slopes greater than one. The different values of slope indicate space charge limited conduction; a change is remarked at 40 MV/m which can defines the beginning of the high fields regime in the case of the studied polymer (Polyethylene Naphthalate).
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 824-827
Electrical characterization of gamma-irradiated polypropylene
The aim of this work is to understand the role of gamma radiation in trap creation and/or trapping and detrapping space charge mechanisms in isotactic polypropylene (iPP). The measurements are performed on 25 μm thick films: virgin polypropylene and one irradiated with gamma rays at a dose of 100 kGy. The experimental study is focused on measuring final thermostimulated discharge currents. At the end of the isothermal discharge process, obtained after charging under a DC field of 4 MV/m, the temperature was increased from 40 °C at a heating rate of 3 °C/mn. As a result, the discharging current of the irradiated film exhibits two peaks, the first one at 75 °C and the second one, of lower amplitude, at 122 °C. It was noticed that no peak was obtained in virgin iPP even at other charging temperatures. Indeed, gamma irradiation creates defects in the polymer that constitute traps of various depths, depending on the nature of the defect. The transient charging current exhibits oscillations (or multiple peaks) associated with charge packets and the current-voltage characteristic shows that the current is controlled by the space charge (IαV 2 ). The differential scanning calorimetry DSC analysis shows a glass transition temperature of 9.4 °C and a crystallization temperature of 114 °C.
- 1 October 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 824-827
Electrical characterization of gamma-irradiated polypropylene
The aim of this work is to understand the role of gamma radiation in trap creation and/or trapping and detrapping space charge mechanisms in isotactic polypropylene (iPP). The measurements are performed on 25 μm thick films: virgin polypropylene and one irradiated with gamma rays at a dose of 100 kGy. The experimental study is focused on measuring final thermostimulated discharge currents. At the end of the isothermal discharge process, obtained after charging under a DC field of 4 MV/m, the temperature was increased from 40 °C at a heating rate of 3 °C/mn. As a result, the discharging current of the irradiated film exhibits two peaks, the first one at 75 °C and the second one, of lower amplitude, at 122 °C. It was noticed that no peak was obtained in virgin iPP even at other charging temperatures. Indeed, gamma irradiation creates defects in the polymer that constitute traps of various depths, depending on the nature of the defect. The transient charging current exhibits oscillations (or multiple peaks) associated with charge packets and the current-voltage characteristic shows that the current is controlled by the space charge (IαV 2 ). The differential scanning calorimetry DSC analysis shows a glass transition temperature of 9.4 °C and a crystallization temperature of 114 °C.