Hongmei Zheng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hongmei Zheng has a total of 42 co-authors. Here are the top co-authors by number of shared publications:
- Ke Chen
School of Mechanical Engineering, Hefei University of Technology, Hefei 230009, China
10 shared publications - Rui Wu
School of Mechanical Engineering, Hefei University of Technology, Hefei, Anhui 230009, China
10 shared publications Ke Chen
Hefei Univ Technol, Sch Mech Engn, Hefei 230009, Anhui, Peoples R China
8 shared publicationsHaishuo Wang
5 shared publicationsXiaopeng Yu
5 shared publicationsGuojun Zhang
4 shared publications
Latest Publications
- Open Access
Research on the Influence of Polygonal Scanner Reflection Point Drift on Measurement Accuracy in a Laser Scanning System
The polygonal scanner is a key component of a laser scanning system. The reflection point drift of a polygonal scanner is one of the primary sources of error that limits improvements in system measurement accuracy, significantly affecting the application of laser scanning systems in high-precision scenarios. Based on a geometric optics model, this article quantitatively analyzes the magnitude of the reflection point drift and the direction of the reflected ray caused by the rotation of the polygonal scanner, as well as the impact of this drift on measurement accuracy. The research shows that, compared to the ideal state, the reflection point drift causes the system’s absolute distortion to increase by nearly 20 times and relative distortion by nearly 5 times, indicating a great effect on measurement accuracy. Future research can directly incorporate this quantitative analysis model into the design of the relevant f-theta lens, effectively and conveniently improving lens design accuracy and thereby enhancing the overall measurement accuracy of the system. This study holds significant theoretical importance and engineering value in advancing the application of laser scanning technology in high-precision scenarios.
Open AccessResearch on the Influence of Polygonal Scanner Reflection Point Drift on Measurement Accuracy in a Laser Scanning System
The polygonal scanner is a key component of a laser scanning system. The reflection point drift of a polygonal scanner is one of the primary sources of error that limits improvements in system measurement accuracy, significantly affecting the application of laser scanning systems in high-precision scenarios. Based on a geometric optics model, this article quantitatively analyzes the magnitude of the reflection point drift and the direction of the reflected ray caused by the rotation of the polygonal scanner, as well as the impact of this drift on measurement accuracy. The research shows that, compared to the ideal state, the reflection point drift causes the system’s absolute distortion to increase by nearly 20 times and relative distortion by nearly 5 times, indicating a great effect on measurement accuracy. Future research can directly incorporate this quantitative analysis model into the design of the relevant f-theta lens, effectively and conveniently improving lens design accuracy and thereby enhancing the overall measurement accuracy of the system. This study holds significant theoretical importance and engineering value in advancing the application of laser scanning technology in high-precision scenarios.
- 3 December 2025
- Published by Elsevier in Control Engineering Practice
- Vol. 168
Hybrid nominal-robust control strategy with error-bounding constraints for enhanced hub motor performance
- 3 December 2025
- Published by Elsevier in Control Engineering Practice
- Vol. 168
Hybrid nominal-robust control strategy with error-bounding constraints for enhanced hub motor performance
- Open Access
Numerical Iterative Design and Analysis of Double Freeform Surface Telecentric F-Theta Lens
As one of the most important optical components of a laser scanning system, the f-theta lens group largely determines the working range and scanning accuracy of this system. In this paper, a numerical iterative design method of a double freeform surface telecentric f-theta lens is proposed. Then the scanning linearity and optical transmittance of the designed f-theta lens are simulated and analyzed. The results show that the f-theta lens designed by this method has a compact structure, large scanning area, extremely high optical transmittance over the entire field of view, and stable, controllable error of scanning linearity. Different from the optimization design method of the traditional f-theta lens group, the two freeform surfaces of this f-theta lens can be obtained directly and simultaneously by using this numerical iterative method, which consumes less computational resources and significantly reduces the design complexity.
Open AccessNumerical Iterative Design and Analysis of Double Freeform Surface Telecentric F-Theta Lens
As one of the most important optical components of a laser scanning system, the f-theta lens group largely determines the working range and scanning accuracy of this system. In this paper, a numerical iterative design method of a double freeform surface telecentric f-theta lens is proposed. Then the scanning linearity and optical transmittance of the designed f-theta lens are simulated and analyzed. The results show that the f-theta lens designed by this method has a compact structure, large scanning area, extremely high optical transmittance over the entire field of view, and stable, controllable error of scanning linearity. Different from the optimization design method of the traditional f-theta lens group, the two freeform surfaces of this f-theta lens can be obtained directly and simultaneously by using this numerical iterative method, which consumes less computational resources and significantly reduces the design complexity.
- 1 June 2024
- Published by Elsevier in Journal of the Franklin Institute
- Vol. 361 (11)
Predefined performance control for fuzzy robotic systems with measurement noise: Adaptation, robustness, and fuzzy optimization
- 1 June 2024
- Published by Elsevier in Journal of the Franklin Institute
- Vol. 361 (11)
Predefined performance control for fuzzy robotic systems with measurement noise: Adaptation, robustness, and fuzzy optimization
- Open Access
- 15 October 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (5) , 1419-1434
Determining Singularity-Free Inner Workspace through Offline Conversion of Assembly Modes for a 3-RRR PPM
The existing singularity avoidance methods have deficiencies, such as the conditionality of the online conversion of the assembly modes (AMs) and the kinematically redundant manipulator with the predicament of the prototype design and added complexit...
- 15 October 2023
- Published by University of Slavonski Brod in Tehnicki vjesnik - Technical Gazette
- Vol. 30 (5) , 1419-1434
Open AccessDetermining Singularity-Free Inner Workspace through Offline Conversion of Assembly Modes for a 3-RRR PPM
The existing singularity avoidance methods have deficiencies, such as the conditionality of the online conversion of the assembly modes (AMs) and the kinematically redundant manipulator with the predicament of the prototype design and added complexit...
- 17 January 2023
- Published by Optica Publishing Group in Applied Optics
- Vol. 62 (3) , 688-696
Cutting sinusoidal gratings to enhance light trapping in thin-film silicon solar cells
A crystalline silicon thin-film solar cell with a three-layer sinusoidal grating structure is studied. The structure has a double-layer antireflection layer, and the three-layer grating is located in the double-layer antireflection layer and the passivation layer, respectively. The related parameters of the grating structure are optimized by scanning using finite-difference time-domain. The optimization results show that cutting the sinusoidal grating structure can significantly improve the light absorption efficiency of the cell for near-infrared light (750–1100 nm), and the enhancement effect is mainly in the transverse electric (TE)-polarized light. This is because the localized surface plasmon resonance and optical waveguide mode under TE-polarized light can be fully excited after the sinusoidal structure is cut. The short-circuit current density ( J S C ) of the optimized three-layer sinusoidal grating structure is 19.82 m A / c m 2 , which is 112.43% higher than that of the planar structure with the same parameters and 23.18% higher than that of the uncut sinusoidal grating structure with the same parameters.
- 17 January 2023
- Published by Optica Publishing Group in Applied Optics
- Vol. 62 (3) , 688-696
Cutting sinusoidal gratings to enhance light trapping in thin-film silicon solar cells
A crystalline silicon thin-film solar cell with a three-layer sinusoidal grating structure is studied. The structure has a double-layer antireflection layer, and the three-layer grating is located in the double-layer antireflection layer and the passivation layer, respectively. The related parameters of the grating structure are optimized by scanning using finite-difference time-domain. The optimization results show that cutting the sinusoidal grating structure can significantly improve the light absorption efficiency of the cell for near-infrared light (750–1100 nm), and the enhancement effect is mainly in the transverse electric (TE)-polarized light. This is because the localized surface plasmon resonance and optical waveguide mode under TE-polarized light can be fully excited after the sinusoidal structure is cut. The short-circuit current density ( J S C ) of the optimized three-layer sinusoidal grating structure is 19.82 m A / c m 2 , which is 112.43% higher than that of the planar structure with the same parameters and 23.18% higher than that of the uncut sinusoidal grating structure with the same parameters.
- 25 June 2022
- Published by Springer Nature in Microsystem Technologies
- Vol. 28 (8) , 1889-1896
Embedded two dimensional metamaterial structure in MIMO antenna array for mutual coupling reduction
- 25 June 2022
- Published by Springer Nature in Microsystem Technologies
- Vol. 28 (8) , 1889-1896
Embedded two dimensional metamaterial structure in MIMO antenna array for mutual coupling reduction
- 12 November 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (33) , 10312-10321
Effective light trapping in c-Si thin-film solar cells with a dual-layer split grating
We propose a dual-layer split nanograting structure in crystalline silicon thin-film solar cells (TFSCs). The split nanograting is designed by introducing two partitioning factors and split times. By employing the finite-difference time-domain method, the light trapping performance and relevant parameters of TFSCs are analyzed and optimized. Numerical computation of optical and electrical simulation shows that the optimal dual-layer split nanograting structure has demonstrated great enhanced light absorption compared with the planar structure. Enhancement of the light trapping effect is associated with light coupling to waveguide modes. The short-circuit current density is reached at 21.66 m A / c m 2 with an improvement of 54.6% over the planar structure. All results provide a parting thought for the design of TFSC grating structures.
- 12 November 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (33) , 10312-10321
Effective light trapping in c-Si thin-film solar cells with a dual-layer split grating
We propose a dual-layer split nanograting structure in crystalline silicon thin-film solar cells (TFSCs). The split nanograting is designed by introducing two partitioning factors and split times. By employing the finite-difference time-domain method, the light trapping performance and relevant parameters of TFSCs are analyzed and optimized. Numerical computation of optical and electrical simulation shows that the optimal dual-layer split nanograting structure has demonstrated great enhanced light absorption compared with the planar structure. Enhancement of the light trapping effect is associated with light coupling to waveguide modes. The short-circuit current density is reached at 21.66 m A / c m 2 with an improvement of 54.6% over the planar structure. All results provide a parting thought for the design of TFSC grating structures.
- 1 June 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (16) , 4938-4947
Enhancement in photocurrent by dual-interface period-mismatched rotating rectangle grating-based c-Si solar cells
A dual-interface period-mismatched rotating rectangular grating structure was designed for crystalline silicon thin film solar cells. The relevant parameters of the grating structures were optimized, and the absorption enhancement mechanisms were also explained by optoelectronic simulation analysis. The numerical results show that the rotating rectangular structure can improve the light-trapping performance by coupling light into the c-Si film to excite the waveguide mode and localized surface plasmon resonances. Moreover, it is found that the light-trapping effect of the rear grating rotating structure is better than that of the front grating rotating structure, because the rear interface can better excite localized surface plasmon resonances. The photocurrent density of the dual-interface period-mismatched rotating rectangular grating structure is increased to 18.01 m A / c m 2 , which is 76.05% higher than that of the planar 300 nm thick c-Si structure. The research results provide general guidance for the design of grating structures for thin-film solar cells.
- 1 June 2021
- Published by Optica Publishing Group in Applied Optics
- Vol. 60 (16) , 4938-4947
Enhancement in photocurrent by dual-interface period-mismatched rotating rectangle grating-based c-Si solar cells
A dual-interface period-mismatched rotating rectangular grating structure was designed for crystalline silicon thin film solar cells. The relevant parameters of the grating structures were optimized, and the absorption enhancement mechanisms were also explained by optoelectronic simulation analysis. The numerical results show that the rotating rectangular structure can improve the light-trapping performance by coupling light into the c-Si film to excite the waveguide mode and localized surface plasmon resonances. Moreover, it is found that the light-trapping effect of the rear grating rotating structure is better than that of the front grating rotating structure, because the rear interface can better excite localized surface plasmon resonances. The photocurrent density of the dual-interface period-mismatched rotating rectangular grating structure is increased to 18.01 m A / c m 2 , which is 76.05% higher than that of the planar 300 nm thick c-Si structure. The research results provide general guidance for the design of grating structures for thin-film solar cells.