Alexander V. Batrakov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Alexander V. Batrakov has a total of 171 co-authors. Here are the top co-authors by number of shared publications:
- Sergey A. Popov
Institute of High Current Electronics, Siberian Branch, Russian Academy of Sciences, Tomsk, Russia
82 shared publications D.I. Proskurovsky
26 shared publications- Anton V. Schneider
Institute of High Current Electronics of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
25 shared publications - Elena L. Dubrovskaya
Institute of High Current Electronics of the Siberian Branch of the Russian Academy of Sciences, Tomsk, Russia
18 shared publications - Sergey A. Onischenko
Institute of High Current Electronics SB RAS, 2/3 Akademichesky Ave., Tomsk, 634055, Russia
11 shared publications Dirk Uhrlandt
Leibniz-Institute for Plasma Science and Technology, Greifswald, Germany
10 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by Tomsk State University in Vestnik Тomskogo gosudarstvennogo universiteta. Khimiya
- No. 34,p. 120-131
Organosilicon coating mass distribution in plasma-chemical reactor based on glow discharge in gas flow
Using the Plasma-Enhanced Chemical Vapour Deposition (PECVD) method, it is possible to synthesize a wide range of different materials, in particular, organosilicon polymer-like coatings. In the present work, a plasma-chemical reactor with coaxial hollow electrodes based on a DC glow discharge maintained in a plasmaforming gas flow at low pressure is used for deposition of a polymer-like coating. Argon was used as a plasma gas with a flow rate of 230 mg/min. Hexamethyldisiloxane was used as a precursor for deposition. Hexamethyldisiloxane was a molecular impurity in the inert gas flow and its flow rate was 10 mg/min. The purpose of the present work is an experimental study of the mass distribution of deposited organosilicon polymer-like coating on various constituent parts of the plasma chemical system based on glow discharge - on the internal surfaces of the reactor and on the substrate located at a distance of 15 mm from the reactor outlet. The experiment showed that at a discharge power of 30 W the total measured mass of the coating amounted to 33 mg. Thus, the mass conversion of the initial substance was over 33%. It is shown that about 90% of the total measured mass of the coating was deposited inside the plasma chemical reactor - on the inner surface of the hollow cathode and the inner surface of the glass tube, and 10% on the substrate. Thus, the present system can be used not only for remote local deposition but also for coating the inner walls of the tubes with a polymer-like coating. It was also revealed that due to the different conditions of processes in the cathode layers and the plasma of the positive column of the glow discharge, some peculiarities of deposition on different surfaces in the system appear. For example, the microstructure of the coatings obtained on the cathode, on the glass tube and on the substrate was investigated using an optical microscope. In this way it was revealed that the coatings consist of rounded microparticles and have a significant difference - the average size of microparticles on the glass tube and substrate cathode is 2-5 microns, which is an order of magnitude lower than the average size of particles deposited on the cathode.
- 1 January 2024
- Published by Tomsk State University in Vestnik Тomskogo gosudarstvennogo universiteta. Khimiya
- No. 34,p. 120-131
Open AccessOrganosilicon coating mass distribution in plasma-chemical reactor based on glow discharge in gas flow
Using the Plasma-Enhanced Chemical Vapour Deposition (PECVD) method, it is possible to synthesize a wide range of different materials, in particular, organosilicon polymer-like coatings. In the present work, a plasma-chemical reactor with coaxial hollow electrodes based on a DC glow discharge maintained in a plasmaforming gas flow at low pressure is used for deposition of a polymer-like coating. Argon was used as a plasma gas with a flow rate of 230 mg/min. Hexamethyldisiloxane was used as a precursor for deposition. Hexamethyldisiloxane was a molecular impurity in the inert gas flow and its flow rate was 10 mg/min. The purpose of the present work is an experimental study of the mass distribution of deposited organosilicon polymer-like coating on various constituent parts of the plasma chemical system based on glow discharge - on the internal surfaces of the reactor and on the substrate located at a distance of 15 mm from the reactor outlet. The experiment showed that at a discharge power of 30 W the total measured mass of the coating amounted to 33 mg. Thus, the mass conversion of the initial substance was over 33%. It is shown that about 90% of the total measured mass of the coating was deposited inside the plasma chemical reactor - on the inner surface of the hollow cathode and the inner surface of the glass tube, and 10% on the substrate. Thus, the present system can be used not only for remote local deposition but also for coating the inner walls of the tubes with a polymer-like coating. It was also revealed that due to the different conditions of processes in the cathode layers and the plasma of the positive column of the glow discharge, some peculiarities of deposition on different surfaces in the system appear. For example, the microstructure of the coatings obtained on the cathode, on the glass tube and on the substrate was investigated using an optical microscope. In this way it was revealed that the coatings consist of rounded microparticles and have a significant difference - the average size of microparticles on the glass tube and substrate cathode is 2-5 microns, which is an order of magnitude lower than the average size of particles deposited on the cathode.
- Open Access
- 1 January 2024
- Published by Tomsk State University in Vestnik Тomskogo gosudarstvennogo universiteta. Khimiya
- No. 34,p. 106-119
Chemical constitution of coatings deposited under hexamethyldisiloxane activation in a glow discharge in a gas flow
The aim of the present work is to reveal peculiarities and regularities of formation of chemical constitution of polymer-like coatings deposited under plasmachemical activation of hexamethyldisiloxane in cathode layers and positive column plasma of glow discharge. The glow discharge was maintained in an argon/hexamethyldisiloxane mixture flow. The argon flow rate was 230 mg/min. The coatings were deposited in six different modes of the plasma-chemical system. The modes were determined by the flow rate of hexamethyldisiloxane, which ranged from 1 to 10 mg/min, and the average discharge current, which was set between 5 and 50 mA. The chemical constitution of the obtained coatings was identified using X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. It is shown that varying the discharge current and hexamethyldisiloxane flow rate in this system produces a wide range of coatings of different chemical constitution. Four different types of coatings obtained were identified: polymethylsiloxane-like structure cross-linked with aliphatic hydrocarbon links with high (C/Si = 9.4) and low (C/Si = 2.9) hydrocarbon linkages, polyhedral oligomeric silsesquioxanes cross-linked with carbosilane, siloxane and aliphatic links with high (C/Si = 5.1) and low (C/Si = 1.5) hydrocarbon linkages. A significant effect of hexamethyldisiloxane flow rate on the chemical structure was found. The most interesting feature of some of the obtained organosilicon coatings is the high relative carbon content. The amount of hydrocarbon links in the coating was found to increase with discharge current. The assumption of formation of hydrocarbon film-forming particles in the cathode layers of the discharge due to ion-induced processes is put forward.
- 1 January 2024
- Published by Tomsk State University in Vestnik Тomskogo gosudarstvennogo universiteta. Khimiya
- No. 34,p. 106-119
Open AccessChemical constitution of coatings deposited under hexamethyldisiloxane activation in a glow discharge in a gas flow
The aim of the present work is to reveal peculiarities and regularities of formation of chemical constitution of polymer-like coatings deposited under plasmachemical activation of hexamethyldisiloxane in cathode layers and positive column plasma of glow discharge. The glow discharge was maintained in an argon/hexamethyldisiloxane mixture flow. The argon flow rate was 230 mg/min. The coatings were deposited in six different modes of the plasma-chemical system. The modes were determined by the flow rate of hexamethyldisiloxane, which ranged from 1 to 10 mg/min, and the average discharge current, which was set between 5 and 50 mA. The chemical constitution of the obtained coatings was identified using X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. It is shown that varying the discharge current and hexamethyldisiloxane flow rate in this system produces a wide range of coatings of different chemical constitution. Four different types of coatings obtained were identified: polymethylsiloxane-like structure cross-linked with aliphatic hydrocarbon links with high (C/Si = 9.4) and low (C/Si = 2.9) hydrocarbon linkages, polyhedral oligomeric silsesquioxanes cross-linked with carbosilane, siloxane and aliphatic links with high (C/Si = 5.1) and low (C/Si = 1.5) hydrocarbon linkages. A significant effect of hexamethyldisiloxane flow rate on the chemical structure was found. The most interesting feature of some of the obtained organosilicon coatings is the high relative carbon content. The amount of hydrocarbon links in the coating was found to increase with discharge current. The assumption of formation of hydrocarbon film-forming particles in the cathode layers of the discharge due to ion-induced processes is put forward.
- 1 March 2023
- Published by Springer Nature in Russian Physics Journal
- Vol. 65 (11) , 1929-1933
High-Speed Videospectroscopy of a High-Current Vacuum-Arc Discharge with Copper-Chromium Electrodes
- 1 March 2023
- Published by Springer Nature in Russian Physics Journal
- Vol. 65 (11) , 1929-1933
High-Speed Videospectroscopy of a High-Current Vacuum-Arc Discharge with Copper-Chromium Electrodes
- 1 October 2021
- Published by Springer Nature in Russian Physics Journal
- Vol. 64 (6) , 1025-1032
Influence of a Non-Stationary Magnetic Field on the Charge Composition and Energy Distribution of Ions of the Cathode Plasma of a Vacuum Arc
- 1 October 2021
- Published by Springer Nature in Russian Physics Journal
- Vol. 64 (6) , 1025-1032
Influence of a Non-Stationary Magnetic Field on the Charge Composition and Energy Distribution of Ions of the Cathode Plasma of a Vacuum Arc
- 10 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (9) , 2567-2574
Measurement of Momentum and Recoil Impulse of Plasma Jet of Vacuum Arc Thruster
To measure the mechanical momentum of a plasma jet, the deflection of a collector suspended on long threads in front of the jet was analyzed (ballistic pendulum method). Alternatively, the recoil impulse in frequency mode of arc operation was measured with a specially designed thrust balance. The dependence of the vacuum arc plasma jet momentum and recoil impulse on the arc current amplitude was studied in the current range from 10 to 800 A. The experiment shows that at a relatively low arc current (100–150 A), the specific reaction force increases and can significantly exceed the above mentioned value. In addition, the specific reaction force strongly increases when the axial magnetic field is applied to the discharge cell. The experiments performed with two cathode materials are also compared. The material presented in the article is of interest for fundamental and methodological issues as well as for applications primarily to the creation and testing of vacuum arc based micro-thrusters ( $\mu $ VAT) for small/ultra-small satellites.
- 10 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (9) , 2567-2574
Measurement of Momentum and Recoil Impulse of Plasma Jet of Vacuum Arc Thruster
To measure the mechanical momentum of a plasma jet, the deflection of a collector suspended on long threads in front of the jet was analyzed (ballistic pendulum method). Alternatively, the recoil impulse in frequency mode of arc operation was measured with a specially designed thrust balance. The dependence of the vacuum arc plasma jet momentum and recoil impulse on the arc current amplitude was studied in the current range from 10 to 800 A. The experiment shows that at a relatively low arc current (100–150 A), the specific reaction force increases and can significantly exceed the above mentioned value. In addition, the specific reaction force strongly increases when the axial magnetic field is applied to the discharge cell. The experiments performed with two cathode materials are also compared. The material presented in the article is of interest for fundamental and methodological issues as well as for applications primarily to the creation and testing of vacuum arc based micro-thrusters ( $\mu $ VAT) for small/ultra-small satellites.
- 20 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (9) , 2505-2515
Advanced Optical Diagnostics for Characterization of Arc Plasmas
This article presents the selected approaches of optical diagnostics applied to thermal arcs. Advanced methods for the determination of temperatures and species density distributions are described and examples of recent developments are presented, such as the consideration of optical depth in optical emission measurements, the use of broadband light sources for measurements of spatially resolved densities, or the combination of spectral analysis with high-speed video observation for the purpose of surface temperature determination. Finally, the potential of the presented diagnostics to solve future challenges of thermal arc research is demonstrated and discussed.
- 20 July 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (9) , 2505-2515
Advanced Optical Diagnostics for Characterization of Arc Plasmas
This article presents the selected approaches of optical diagnostics applied to thermal arcs. Advanced methods for the determination of temperatures and species density distributions are described and examples of recent developments are presented, such as the consideration of optical depth in optical emission measurements, the use of broadband light sources for measurements of spatially resolved densities, or the combination of spectral analysis with high-speed video observation for the purpose of surface temperature determination. Finally, the potential of the presented diagnostics to solve future challenges of thermal arc research is demonstrated and discussed.
- 8 May 2021
- Published by Springer Nature in Russian Physics Journal
- Vol. 64 (1) , 130-136
A Study of Transient Processes in a High-Current Vacuum-Arc Anode Spot Using High-Speed Spectroscopy and Videorecording
- 8 May 2021
- Published by Springer Nature in Russian Physics Journal
- Vol. 64 (1) , 130-136
A Study of Transient Processes in a High-Current Vacuum-Arc Anode Spot Using High-Speed Spectroscopy and Videorecording
- 14 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1132-1135
Plasma-Assisted Deposition of Dielectric Conformal Coating Using Hexamethyldisiloxane as Precursor
Plasma polymerization is a rapidly growing field of plasma technology. Using this method, it is possible to solve applied problems, for example, the deposition of conformal dielectric coatings to protect electrical circuit boards operating in outer space. In this paper, we study the vapor deposition of hexamethyldisiloxane using low-pressure plasma. The morphology, dielectric strength under plasma, and chemical composition of the deposited coating are studied. It was established that the coating has a lamellar structure, which, together with the data of IR spectroscopy, indirectly prove the formation of a polymer coating. The dielectric strength of the coating under plasma was 650 V.
- 14 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1132-1135
Plasma-Assisted Deposition of Dielectric Conformal Coating Using Hexamethyldisiloxane as Precursor
Plasma polymerization is a rapidly growing field of plasma technology. Using this method, it is possible to solve applied problems, for example, the deposition of conformal dielectric coatings to protect electrical circuit boards operating in outer space. In this paper, we study the vapor deposition of hexamethyldisiloxane using low-pressure plasma. The morphology, dielectric strength under plasma, and chemical composition of the deposited coating are studied. It was established that the coating has a lamellar structure, which, together with the data of IR spectroscopy, indirectly prove the formation of a polymer coating. The dielectric strength of the coating under plasma was 650 V.
- 14 July 2020
- Published by Springer Nature in Russian Physics Journal
- Vol. 63 (3) , 508-515
Experimental Study of Space Charge Structure and Expansion Dynamics of Laser Ablation Plasma
- 14 July 2020
- Published by Springer Nature in Russian Physics Journal
- Vol. 63 (3) , 508-515
Experimental Study of Space Charge Structure and Expansion Dynamics of Laser Ablation Plasma
- 1 March 2020
- Published by Tomsk State University in Izvestiya vysshikh uchebnykh zavedenii. Fizika
- No. 3,p. 145-151
Experimental study of space-charge structure and expansion dynamics of laser ablation plasma
- 1 March 2020
- Published by Tomsk State University in Izvestiya vysshikh uchebnykh zavedenii. Fizika
- No. 3,p. 145-151
Experimental study of space-charge structure and expansion dynamics of laser ablation plasma