JTJohn R. Tyrer

John R. Tyrer

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


John R. Tyrer has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Peri-dyeing: Laser dye fixation for efficient textile colouration and design

    by Laura Morgan, Jinsong Shen, Faith Kane, John Tyrer

  • Laser cutting hazards of nuclear infrastructure decommissioning and dismantling

    by Lewis C. R. Jones, Jacob Lavin, Andrew Cousins, Mathew Jones, Edward J. Long, Julian T. Spencer, Jonathan M. Dodds, John R. Tyrer

    Laser cutting for nuclear decommissioning and dismantling presents unique challenges in aerosol hazard control and radiation safety. The UK's Nuclear Decommissioning Authority, responsible for Europe's largest nuclear decommissioning program, has identified laser cutting as a suitable process for decommissioning. However, the generation of hazardous aerosolized by-products during laser cutting limits its implementation as a nuclear decommissioning tool. Current control methods rely heavily on human intervention during waste filter loading and unloading, potentially introducing unnecessary radiation exposure that could be mitigated through engineering controls. Lasers are known to generate a range of aerosols during the cutting process. The high temperatures and gas pressures of the laser process can cause the volatile breakdown of metals and the formation of particles < Ø 1 μm. While these can be challenging to control in the manufacturing environment, they increase the complexity of extraction and filtration during nuclear decommissioning and dismantling. This paper incorporates previous studies into the effect of gas dynamics on the generation mechanisms of laser fume, transportation mechanics of laser-generated aerosols, and the effects of laser particulate on filtration systems. It identifies a range of laser-generated aerosol hazards from the laser cutting of steel infrastructure. It presents a set of recommendations for the cutting process and ventilation systems to improve the risk assessment of laser cutting for nuclear decommissioning and dismantling.


  • Open Access

    Industrial Energy Optimisation: A Laser Cutting Case Study

    by Nicholas Goffin, Lewis C. R. Jones, John R. Tyrer, Jinglei Ouyang, Paul Mativenga, Lin Li, Elliot Woolley

    In an increasingly technological world, energy efficiency in manufacturing is of great importance. While large manufacturing corporations have the resources to commission energy studies with minimal impact on operations, this is not true for small and medium enterprises (SME’s). These businesses will commonly only have a small number of laser processing cells; thus, to carry out an energy study can be extremely disruptive to normal operations. Since rising global energy costs also have the largest impact on small businesses who lack the benefit of economies of scale, they are simultaneously the most in need of improvements to energy efficiency, while also facing the strongest practical barriers to implementing them. In this study, a laser processing energy analysis methodology was designed to run simultaneously with normal operation and applied to a laser shim-cutting cell in a UK-based SME. This paper demonstrates the methodology for identifying operating states in a production environment and Specific Energy Consumption and Scope 2 CO2 emissions results are analysed. The Processing state itself was the most impactful on overall energy performance, at 55% for single sheets of material, increasing to 71% when batch processing. Generating idealised data in this production environment is challenging with restrictions to isolating variables, these “real-world” limitations for conducting system energy analysis simultaneously with live production are also discussed to present recommendations for further analysis.


  • Open Access

    Reducing environmental risks in laser cutting: A study of low-pressure gas dynamics

    by Jacob J. Lavin, Jay J. Robus, Toby Williams, Edward J. Long, John R. Tyrer, Julian T. Spencer, Jonathan M. Dodds, Lewis C. R. Jones

    High gas pressures (1.0–1.6 MPa) are employed in conventional inert laser cutting to achieve efficient material removal and high cut quality. However, this approach results in the emission of large quantities of by-products, which can pose a risk to human health and the environment. For applications such as nuclear decommissioning, where global extraction and containment can be challenging, hazardous by-product formation, rather than process efficiency, is the main priority. This paper demonstrates low-pressure (0.3–0.6 MPa) laser-cutting techniques developed to reduce by-products. This study investigates the causal links between melt ejection and gas dynamic interactions in low-pressure laser cutting. Experiments were conducted using a 300 W Nd:Yb fiber laser to cut 304 stainless steel samples. Melt ejection and breakdown profiles were captured using a FASTCAM mini AX 200 camera. The lens combination fitted to the camera provided a spatial resolution of approximately 1 μm. The gas dynamic interactions were assessed through comparisons with existing studies of Schlieren imaging in idealized environments. The results show that gas dynamics are crucial in melt ejection and breakdown mechanisms during laser cutting. The key findings of this study are images of breakdown mechanisms linked to low-pressure gas dynamics. The impact of this work is that breakdown mechanisms more favorable to reducing environmental risk have been demonstrated. A greater understanding of the risk is indispensable to developing new laser-cutting control methods for hazardous materials.


  • Open Access

    Analysis of laser-generated plume concentration during in vivo laser hair reduction procedures in a tertiary referral laser dermatology unit

    by Lewis C R Jones, Jason Britton, Audrey McCartney, Paula Kipling-Steels, Rachel Urwin, Daniel Lloyd, John R Tyrer

    Dear Editor, Laser hair reduction is one of the most common cosmetic treatments, representing approximately half of the procedures in the observed unit. However, the selective photothermolysis process produces a malodorous and visible plume (surgical smoke).1 In vitro studies have identified 13 carcinogens and 20 environmental toxins in the plume,2 and literature reviews have identified risks of infection, carcinogenesis and pulmonary damage from laser dermatological surgical smoke.3 British Medical Laser Association (BMLA) guidance emphasizes aerosol management for COVID-19 infection risk and risk assessment-identified laser-generated plume hazards.4 This study was conducted to quantify laser-generated plume concentration in the air to understand the adequacy of the current control methods (the data underlying this article are available in the Loughborough University Repository, at https://dx.doi.org/10.17028/rd.lboro.20517519).


  • Open Access

    Laser specific energy consumption: How do laser systems compare to other manufacturing processes?

    by Lewis C. R. Jones, Nicholas Goffin, Jinglei Ouyang, Nazanin Mirhossein, Jiaji Xiong, Yufeng Li, Lin Li, John Tyrer, Zhu Liu, Elliot Woolley, et al.

    Laser material interactions are routinely praised for their selective processing and high processing rates. However, this does not guarantee that the total manufacturing system has a low energy intensity compared to conventional manufacturing processes. This paper presents the results of a collaborative UK and China research project to improve the comprehension of the total energy consumption and carbon emissions for laser-based manufacturing. A range of individual laser cutting, welding, and cleaning processes were studied to assess their energy efficiency, including the laser and its ancillary subsystems (e.g., cooling and extraction). The project developed a systematic analysis method, adapted from BS ISO 14955-1:2017, which incorporated time and subsystem level studies to quantify all energy consumption components of a laser system. Previous research has identified that the laser system's most significant contributor to the total energy consumption are the auxiliary or supporting subsystems, not the laser emission. This identified that using only the absorbed radiation to evaluate manufacturing efficiency is misleading. All the processes evaluated followed a negative correlation between processing rate (kg/h) and specific energy consumption (J/kg). The new data conclude that laser processes have a relatively high energy intensity compared to conventional manufacturing alternatives. The results can be used to identify where the most significant improvements to individual laser systems can be made. The comprehensive comparison of processes allows manufacturers to select processes to improve environmental impact.


  • Open Access

    Selective laser crystallization and amorphization in polymer fibers

    by Francesca Wheeler, John R. Tyrer, Lewis C. R. Jones

    Textile finishing is a huge industry for modification of textile surface properties to align with the desired end use spanning medical, engineering, and apparel applications. Laser-induced polymer morphology modification has been studied by researchers, with evidence suggesting a correlation between laser fluence and crystallinity. However, a lack of data has resulted in the mechanism for change remaining unknown. This paper aims to identify the mechanism of initial Young’s modulus control in polyethylene terephthalate (PET) monofilament yarn and explain the relationship between Young’s modulus and the degree of crystallinity using Takayanagi’s model. PET monofilament yarns were treated using a CO2 infrared laser at a 10.6 μm wavelength at fluences up to 0.086 J/mm2. Young’s modulus data obtained from stress-strain curves at 0.2% strain and fraction crystallinities obtained from differential scanning calorimetry were compared with Takayanagi’s series model. Laser surface treatment within a fluence range up to 0.087 J/mm2 on PET resulted in stable Young’s modulus values. A 3.5% reduction in Young’s modulus of PET was seen with a 6.1% reduction in crystallinity, which was in good agreement with Takayanagi’s series model. Lasers offer rapid material processing capable of increasing or decreasing fractional crystallinity selectively along the fiber where desired. Selective amorphization increases chemical absorption, allowing increased surface finishing uptake at milder processing conditions, whereas increasing fractional crystallinity imparts fiber strength. The relationship between fiber crystallinity and Young’s modulus for PET can be described by Takayanagi’s model, allowing a prediction of material properties, which can be extended from fibers to all thin-film polymers.


  • Open Access

    Controlling nozzle and kerf gas dynamics to manage hazardous laser cutting fume

    by Jacob J. Lavin, Mathew T. Jones, Edward J. Long, John R. Tyrer, Julian T. Spencer, Jonathan M. Dodds, Lewis C. R. Jones

    Conventional laser cutting is optimized for cut speed and quality but does not consider process fume. When processing hazardous materials in environments where global extraction is not practical, such as during in situ nuclear decommissioning, consideration of process fume is critically important. Fume generation in laser cutting is governed by forces applied to the molten cut front; dynamic interactions between the assist-gas and the cut front control these forces. This paper investigates the causal links between key gas-dynamic features and fume generation mechanisms in laser cutting. Its aim is to provide the preliminary understanding required to design process setups targeted at reducing the fine particle fraction. During laser cutting, the assist-gas boundary layer separates (BLS) from the molten cut front and, therefore, downstream forces applied on the melt are significantly changed. In this work, the BLS point is analyzed, captured via schlieren imaging, in an idealized environment. This separation point is related to features on the cut wall of laser-cut samples, validating the gas-dynamic interactions. The samples were cut from 3 mm thick 304 stainless steel, using a 1 kW Nd:Yb fiber laser. Control of the surface stagnation pressure and gas flow boundary conditions were used to relocate the point of BLS within the cut front, and the relationship of these parameters was analyzed. The results demonstrate that shifting the point of BLS along the cut front can be used to control fume generation mechanisms. This study successfully provided the preliminary understanding necessary to manage fume generation during the laser cutting process.


  • Open Access

    Simulated and experimental analysis of laser beam energy profiles to improve efficiency in wire-fed laser deposition

    by Nicholas Goffin, John R. Tyrer, Lewis C. R. Jones, Rebecca L. Higginson

    Laser cladding is a well-established technique, with the majority of prior numerical modelling work focused on delivery and melt pool behaviour of powder-based processes. This research presents new investigations into optimised laser beam shaping for the unique characteristics of wire-based processes, where direct substrate heating, as well as heat transfer between the wire and substrate, is important. The value of this subject is the improved deposition rates and dense metallic structures that can be achieved by wire-based deposition processes compared to powder-based material delivery. The within-wire temperature distribution (AISI 316 stainless steel), the heat transfer and direct heating of the substrate (mild steel) are modelled via heat transfer simulations, with three laser beam irradiance distributions. This analysis identified the removal of localised high-temperature regions typically associated to standard Gaussian distributions, and the improved substrate heating that a uniform square beam profile can provide. Experiments using pre-placed wire and a 1.2 kW CO2 laser were analysed using cross-sectional optical microscopy to provide model validation and evidence of improved wire-substrate wetting, while maintaining favourable austenitic metallurgy in the clad material. A key finding of this work is a reduction, from 480 to 190 W/mm2, in the required irradiance for effective melt pool formation when changing from a Gaussian distribution to a uniform square distribution. This also provided a 50% reduction in total energy. The potential improvements to energy efficiency, cost reductions and sustainability improvements are recognised and discussed.


  • Open Access

    Engineering controls for surgical smoke in laser medical handpieces

    by Lewis C. R. Jones, Mark Parry, Jason Britton, John R. Tyrer

    The hazard of surgical smoke is often overlooked when considering the safety of medical laser procedures but can present a high level of occupational risk. Administrative procedures for operating external extraction devices and the reliance on personal protective equipment are not sufficient for reducing the risk. This paper aims to quantify the hazard of laser-generated surgical smoke and demonstrate how effective engineering control solutions can reduce the risk. A new design solution is presented with engineering controls for surgical smoke extraction and optical radiation integrated into the laser handpiece. A fiber delivered diode laser is used to simulate laser vaporization procedures on porcine skin tissue. Conventional external extraction conditions are compared to the new design solution. Fine particulate mass concentrations (PM2.5) from the simulated procedures, under different extraction conditions, are measured using optical particle size measurements. Peak concentrations of 55.86 ± 2.79 μg/m3 were measured without extraction; showing that the hazard of laser-generated surgical smoke is five times greater than the World Health Organization guideline of 10 μg/m3. A typical medical extraction setup only achieved a 16% reduction in peak concentration values, 47.07 ± 2.35 μg/m3; demonstrating that conventional, external, methods of extraction are ineffective. The new solution was able to capture all particulate materials, reducing particulate concentrations to background levels, 2.19 ± 0.68 μg/m3, safely below the current recommended guidelines. The design and results present evidence that it is not only more effective to use engineering control methods but that it is practicable to do so.