Liliana Melro

In this study, a material based on polyethylene (PE) and microcrystalline cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3-aminopropyltriethoxysilane (APTES) has been shown to be an efficient option to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such as polyethylene (PE). The functionalization of MC with the mentioned silane derivative was achieved using a green method and later used in the development of composites with PE in three percentages (1, 3, and 5%). All the materials were prepared by melt blending and characterized in terms of structural properties (ATR-FTIR and FTIR in transmittance mode, EDX, and SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to water vapor. The materials demonstrated the potential to be used as breathable film packaging for fresh products.

In this study a material based on Polyethylene (PE) and Microcrystalline Cellulose (MC) was developed as a breathable packaging film. Surface functionalization of MC with 3 aminopropyltriethoxysilane (APTES) shows to be an efficient alternative to tailor their properties and increase opportunities for the application of MC on the reinforcement of polymers such polyethylene (PE). Functionalization of MC with mentioned silane derivative was achieved using a green method and later used on the development of composites with PE in three percentages (1, 3 and 5%). All the materials were prepared by melt blending and characterized, in terms of structural properties (ATR-FTIR and FTIR in transmittance, EDX, SEM), thermal properties (DSC and TGA), thermomechanical properties (DMA), contact angle measurements and permeability to oxygen and water vapor. The materials demonstrated to have potential to be used as breathable film packaging of fresh products.

Laboratories and industries that handle chemicals are ubiquitously prone to leakages. These may occur in storage rooms, cabinets or even in temporary locations, such as workbenches and shelves. A relevant number of these chemicals are corrosive, thus commercial products already exist to prevent material damage and injuries. One strategy consists of the use of absorbing mats, where few display neutralizing properties, and even less a controlled neutralization. Nevertheless, to the authors’ knowledge, the commercially available neutralizing mats are solely dedicated to neutralizing acid or alkali solutions, never both. Therefore, this work describes the development and proof of a completely novel concept, where a dual component active mat (DCAM) is able to perform a controlled simultaneous neutralization of acid and alkali leakages by using microencapsulated active components. Moreover, its active components comprise food-grade ingredients, embedded in nonwoven polypropylene. The acid neutralizing mats contain sodium carbonate (Na₂CO₃) encapsulated in sodium alginate microcapsules (MC-ASC). Alkali neutralizing mats possess commercial encapsulated citric acid in hydrogenated palm oil (MIRCAP CT 85-H). A DCAM encompasses both MC-ASC and MIRCAP CT 85-H and was able to neutralize solutions up to 10% (v/v) of hydrochloric acid (HCl) and sodium hydroxide (NaOH). The efficacy of the neutralization was assessed by direct titration and using pH strip measurement tests to simulate the leakages. Due to the complexity of neutralization efficacy evaluation based solely on pH value, a thorough conductivity study was performed. DCAM reduced the conductivity of HCl and NaOH (1% and 2% (v/v)) in over 70%. The composites were characterized by scanning electron microscopy (SEM), differential calorimetry (DSC) and thermogravimetric analysis (TGA). The size of MC-ASC microcapsules ranged from 2 μm to 8 μm. Finally, all mat components displayed thermal stability above 150 °C.

Burn wounds can lead to numerous severe complications including bacterial infections causing patient morbidity and mortality, mostly in low- and middle-income countries. The considerable increase in microbial resistance against traditional antibiotics is leading towards alternative strategies to treat bacterial infections. Nisin Z is an antimicrobial peptide which exhibits a significant antibacterial activity against Gram-positive bacteria. Its efficacy against Gram-negative bacteria is limited, nonetheless it can be improved with the addition of surfactants, such as ethylenediaminetetraacetic acid (EDTA). The incorporation of peptide and other biomolecules within a biopolymer matrix provides protection maintaining their antimicrobial potential. Bacterial nanocellulose (BNC) has been widely used as wound dressings. Its impressive water retention capacity (>99%) and porosity are beneficial to manage wounds due to its potential to absorb exudates, providing a breathable and humid environment. In this work, the functionalization of BNC with Nisin Z (BNC-NZ) via vacuum filtration is reported. The entrapment of the peptide inside the BNC films was confirmed through morphological characterization using attenuated total reflectance-Fourier transform infrared (ATR-FTIR) spectrometry. Typical absorbance peaks of Nisin Z are easily identifiable at 1647 cm⁻¹ (amide group) and 1520 cm⁻¹ (bending of primary amines). Thermal gravimetric analysis (TGA) suggested that Nisin Z did not interfere with the BNC matrix. The antimicrobial activity of Nisin Z against five of the most common bacteria found in burn wounds was verified by minimum bactericidal concentration (MBC) ranging 8.0–256.0 µg/mL. Agar diffusion and shake flask methods revealed the potential of BNC-NZ for prospective applications in burn wound dressings.

Nanotechnology is a powerful tool for engineering functional materials that has the potential to transform textiles into high-performance, value-added products. In recent years, there has been considerable interest in the development of functional textiles using metal nanoparticles (MNPs). The incorporation of MNPs in textiles allows for the obtention of multifunctional properties, such as ultraviolet (UV) protection, self-cleaning, and electrical conductivity, as well as antimicrobial, antistatic, antiwrinkle, and flame retardant properties, without compromising the inherent characteristics of the textile. Environmental sustainability is also one of the main motivations in development and innovation in the textile industry. Thus, the synthesis of MNPs using ecofriendly sources, such as polysaccharides, is of high importance. The main functions of polysaccharides in these processes are the reduction and stabilization of MNPs, as well as the adhesion of MNPs onto fabrics. This review covers the major research attempts to obtain textiles with different functional properties using polysaccharides and MNPs. The main polysaccharides reported include chitosan, alginate, starch, cyclodextrins, and cellulose, with silver, zinc, copper, and titanium being the most explored MNPs. The potential applications of these functionalized textiles are also reported, and they include healthcare (wound dressing, drug release), protection (antimicrobial activity, UV protection, flame retardant), and environmental remediation (catalysts).