APAnton V. Polunin

Anton V. Polunin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Anton V. Polunin has a total of 36 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • The Mechanical and Corrosion Properties of Ceria-Reinforced PEO Coatings on Mg–RE Alloy

    by E. D. Borgardt, A. O. Polunina, M. R. Shafeev, A. V. Polunin, M. M. Krishtal

    Limitations in the possibilities of using such interesting materials in terms of the ratio of density and volumetric mechanical characteristics as magnesium alloys with the addition of rare earth elements (Mg–RE), associated with the low corrosion properties of their surface, impose the need to search for and improve methods for its improvement. Of particular importance is the elimination of the phenomenon of microgalvanic corrosion that occurs at the interfaces between the phases of the alloy matrix (a-Mg) and secondary strengthening phases. The mechanical properties of the Mg–RE surface are also insufficient for work under contact conditions. In this research, the method of electrochemical formation of conversion protective ceramic layers—plasma electrolytic oxidation (PEO)—was modified by the addition of cerium dioxide particles CeO2 into the electrolyte at two modes (medium (250 Hz) and high (1000 Hz)) of technological pulse frequencies. It has been established that the mechanism of incorporation of dispersed particles of cerium dioxide consists of both electrophoretic incorporation of particles into the forming coating and thermokinetic inert incorporation as a result of impact interaction of particles and the oxide layer, and in both cases, preservation of CeO2 particles in its original state occurs. Modification of coatings with CeO2 particles allowed increasing resistance to chipping by up to 50 times and reduce the chip area during indentation from ~0.5 up to ~0.01 mm2, and the use of high-frequency PEO mode, in general, improves resistance to chipping by ~2–3 times, regardless of the concentration of CeO2 particles in the electrolyte compared to the mid-frequency. The CeO2 particles had greatest influence on the wear resistance of the oxide coating—high-frequency PEO with the addition of CeO2 allowed reducing the values of specific wear to ~0.05–0.1 µm/(N m) at high frequency PEO versus with ~0.3 µm/(N m) for the base coating obtained in mid-frequency PEO. Without the addition of particles, high-frequency PEO allowed reducing the wear of the base coating in the experiment by ~1.5 times compared to the medium-frequency one, which indicates the synergy of the interaction of the CeO2 additive and high-frequency PEO. Studies of the corrosion properties of coatings have shown that CeO2 particles slightly reduced the original characteristics, however, with prolonged exposure to a corrosive medium, some restoration of the corrosion properties of the coatings and the formation of a new corrosion-resistant phase in them—Mg0.667Al0.333(OH)2(CO3)0.167(H2O)0.5 (hydrotalcite)—is observed.

  • The Effect of Ceria Particles Incorporation on Protective Properties of Oxide Layers Formed by PEO on Mg Alloy with LPSO-Phase

    by E. D. Borgardt, A. O. Polunina, M. R. Shafeev, A. V. Polunin, M. M. Krishtal

    The progress in the magnesium alloy design technology has enabled outstanding characteristics to be achieved for alloys containing both the strengthening LPSO phase (long-period stacking-ordered phase, LPSO) and rare earth elements (Mg–Gd–X, Mg–Nd–X, Mg–Y–X, Mg–Sc–X, and other systems): increase the allowable continuous service temperatures to ~250–300°C, the tensile strength to ~930 MPa, the relative elongation to ~30%, and the hardness to ~190 HV. However, the phenomenon of microgalvanic corrosion arising from the potential difference between the LPSO phase and the α-Mg matrix at their interface, as well as insufficient surface hardness, are the main problems of these alloys, necessitating surface modification for most applications. In this study, the plasma electrolytic oxidation (PEO) technology for treatment of light alloys was modified by adding cerium dioxide (CeO2) particles to the electrolyte in order to improve the characteristics of oxide layers formed on a Mg–Y–Zn–Yb–Zr alloy with the LPSO phase. The additive concentration (1–5 g/L, with a 1 g/L increment) and the forming pulse frequency of the process current (250 and 1000 Hz) were varied. Consequently, the high-frequency (1000 Hz) PEO with the addition of 4 g/L СeO2 to the electrolyte allowed the average microhardness to be increased from ~350 to ~690 MPa, i.e., by ~2 times, and the adhesion strength to be improved by 40% relative to the basic variant. The incorporation of CeO2 had a negligible effect on the corrosion resistance of the layers; the most pronounced positive effect was observed at a PEO frequency of 1000 Hz and at a CeO2 particle concentration of 1 g/L: the polarization resistance of the oxide layer was ~8.2 MΩ cm2, the corrosion current density was ~3.8 nA/cm2, and the impedance modulus was ~4.2 MΩ cm2 in comparison with the respective characteristics of ~4.3 MΩ cm2, ~9.8 nA/cm2, and ~3.0 MΩ cm2 for the basic oxide layer, which is due to the inert (no chemical reactions involved) incorporation of cerium oxide particles into the layer, its compacted structure, and reduced porosity.


  • Open Access

    Improvement of protective oxide layers formed by high-frequency plasma electrolytic oxidation on Mg-RE alloy with LPSO-phase

    by Alisa O. Cheretaeva, Pavel A. Glukhov, Marat R. Shafeev, Alyona G. Denisova, Eugeny D. Borgardt, Anton V. Polunin, Alexander V. Katsman, Mikhail M. Krishtal

    Oxide layers on Mg97Y2Zn1 magnesium alloy with strengthening LPSO-phase were formed by plasma electrolytic oxidation (PEO) in bipolar mode with frequency variation of forming current pulses (50 and 500 Hz) and addition of sodium aluminate or sodium silicate to alkali phosphate fluoride electrolyte. Microstructure, chemical and phase composition, corrosion and mechanical properties of the oxide layers formed were investigated. With increasing current frequency for both electrolytes, an increase in homogeneity of the oxide layers structure and a decrease in their porosity and fracturing at constant thickness were recorded. The oxide layers formed at 500 Hz even with some decrease in hardness have better adhesive strength and 2 orders of magnitude higher short-term corrosion resistance values. PEO of Mg-alloy with LPSO-phase in the electrolyte with addition of sodium aluminate in combination with increased pulse frequency (500 Hz) allows forming the best-quality uniform oxide layer with high hardness, adhesive strength and corrosion resistance properties. The use of electrolyte with addition of sodium silicate reduced the adhesive strength by 1.5 times and brought down the long-term corrosion resistance of oxide layers by an order of magnitude, as compared with the electrolyte with sodium aluminate. The reason for a significant improvement in the complex of protective properties of the oxide layers with an increase in the current pulse frequency is supposed to be a decrease in the power and duration of individual microarc discharges with simultaneous increase in their number per unit oxidized area.


  • Assessing residual stresses in the surface layer of the ZK60 alloy after an exposure to corrosion solution

    by Evgeniy Merson, Vitaly Poluyanov, Anton Polunin, Pavel Myagkikh, Dmitri Merson, Alexei Vinogradov

    Magnesium alloys preliminary immersed in a corrosion solution suffer from embrittlement, referred to as pre-exposure stress corrosion cracking (PESCC).


  • Open Access

    The influence of addition of ZrO2 nanoparticles to the electrolyte on the structure and anticorrosion properties of oxide layers formed by plasma electrolytic oxidation on the Mg97Y2Zn1 alloy

    by Togliatti State University, A. O. Polunina, A. V. Polunin, Михаил Михайлович Криштал

    Magnesium alloys with a strengthening long-period stacking ordered structure (LPSO-phase) offer outstanding mechanical properties, but their low corrosion resistance necessitates additional surface protection. The work investigates the influence of adding ZrO2 nanoparticles at a concentration of 1–4 g/l to the electrolyte on the thickness, structure, composition, wettability, and anticorrosion properties of oxide layers formed during plasma electrolytic oxidation (PEO) of the Mg97Y2Zn1 alloy with the LPSO-phase. It was found that during PEO, under the influence of an electric field, ZrO2 nanoparticles penetrate into the forming oxide layer and reduce its porosity. The study revealed a decrease in the quantity and size of pores near the barrier layer in places where the alloy LPSO-phase comes out to the interface with the oxide layer. Low concentrations of ZrO2 nanoparticles (1–2 g/l) reduce the corrosion rate of the alloy up to two times compared to the base case. The minimum corrosion current density icorr≈14 nA/cm2 and the highest polarization resistance Rp≈2.6 MΩ·cm2 are found in the sample formed in an electrolyte with the addition of 1 g/l of ZrO2 nanoparticles. Calculation of the barrier zone parameters of oxide layers showed that an increase in the ZrO2 concentration in the electrolyte leads to an increase in the barrier layer thickness and in its specific conductivity, which negatively affects the corrosion resistance of the formed oxide layers – the barrier zone resistance of the layer obtained by adding 4 g/l of ZrO2, drops by ~20 % compared to the base case (up to ~1 MΩ·cm2).


  • Open Access

    Cyclic regularities of the acoustic emission generation during plasma-electrolytic oxidation of an Al–Mg alloy in the bipolar mode

    by Togliatti State University, Игорь Анатольевич Растегаев, Марат Равилович Шафеев, Инна Ивановна Растегаева, Антон Викторович Полунин, Михаил Михайлович Криштал

    The paper analyzes the features of the acoustic emission (AE) signal generation during plasma-electrolytic oxidation (PEO) of the AMg6 aluminum alloy in a bipolar (anode-cathode) pulsed mode within each cycle of voltage application. The authors studied the range of PEO modes that almost completely covers all standard technological modes for processing aluminum alloys by the current densities (6–18 A/dm2) and current ratio in half-cycles (0.7–1.3), which allowed fixing and studying the AE accompanying the formation of oxide layers for various purposes. For the first time, due to AE registration, a new PEO stage was identified, in which there was no microarc breakdown to the substrate, but which was accompanied by an increase in the layer thickness, and the nature of which has not yet been determined. According to the known features of the oxidation stages, the authors systematized the repetitive forms of AE manifestation in the cycles of exposure and identified their five types and three subtypes. The study shows that the approach used to establish the PEO stages by the “acoustic emission amplitude” parameter has poor accuracy, since it does not take into account the form of signals and the half-period of their registration. Therefore, the authors developed and tested a new approach for analyzing AE frames synchronously with the cycles of change in the forming voltage during PEO, and proposed a new “acoustic-emission median” parameter, which allows identifying the main types and subtypes of signals accompanying the oxidation stages. An experimental study of the proposed AE parameter was carried out to identify these PEO stages, which confirmed the operability, high accuracy and sensitivity of the proposed parameter to the subtypes of AE signals recorded at the cathode stage of “soft sparking”. The latter is of particular interest, since it is a means of studying a given oxidation stage with a resolution equal to the exposure cycle.


  • Open Access

    Different-sized porosity and thermal conductivity of oxide layers formed by plasma-electrolytic oxidation on the AK12D silumin

    by Togliatti State University, Павел Валентинович Ивашин, Михаил Михайлович Криштал, A. Ya. Tverdokhlebov, Антон Викторович Полунин, Наталья Юрьевна Дударева, Ufa University of Science and Technology, Александр Борисович Круглов, National Research Nuclear University MEPhI, Андрей Яковлевич Твердохлебов

    Oxide layers formed by plasma-electrolytic oxidation (PEO) are characterized by a sufficiently high porosity, which influences almost the whole complex of service characteristics. However, the known data on the integral porosity of PEO-produced layers are rather contradictory, and the nature of the pore size distribution in these layers remains understudied. As a result of processing the images of the layer cross-section produced in a wide magnification range (scanning electron microscopy – SEM, image-based analysis), the authors obtained the pore size distribution in the range of 10 nm to 10 µm, which is sufficiently well described by a lognormal distribution function (pore geometry was approximated by a spherical shape). Such distribution pattern indicates the nature of pore formation, which can be related to the thermally activated process of gas emission from a liquid melt, the volume and average temperature of which, in their turn, depend on the micro-arc discharge energy. The paper presents the results of identifying the oxide layer phase composition and crystallites sizes by the X-ray crystallography method. Comparing the results of X-ray spectral microanalysis and X-ray crystallography, the amorphous component phase composition was evaluated. Using the stationary method and the method of pulsed laser heating, the authors determined the thermal conductivity of the initial oxide layer and the layer after the removal of its highly-porous outer part. The porosity values obtained experimentally and calculated based on the analysis of SEM-images and the results of determining the phase composition, including amorphous phases, allowed evaluating the oxide layer thermal conductivity with the help of four known analytical models. The results of calculating the thermal conductivity using the Loeb model showed good convergence with the experimental results obtained in this work. The modeling demonstrated that the size of crystallites influence the oxide layer thermal conductivity much less than the porosity and amorphous phase.


  • Open Access

    The effect of process current parameters on the properties of oxide layers under plasma electrolytic oxidation of AMg6 alloy

    by A V Polunin, A G Denisova, A O Cheretaeva, M R Shafeev, E D Borgardt, I A Rastegaev, A V Katsman

    The effect of current density and current ratio in the cathodic and anodic half-cycles during prolonged (180 minutes) plasma electrolytic oxidation (PEO) of AMg6 wrought alloy on the oxide layer wear and corrosion resistance were studied. It was established that the best wear resistance is achieved in the oxide layers obtained in the “soft sparking” mode (negative-to-positive pulse ratios of 1.15–1.30) at current densities of 9–15 A dm−2, and the best set of wear resistance and corrosion resistance – in the oxide layers obtained in “symmetrical” mode (negative-to-positive pulse ratio of 1.00).


  • Open Access

    The effect of current frequency on the structure, composition and properties of oxide layers formed by plasma electrolytic oxidation on aluminum-silicon alloy

    by A V Polunin, E D Borgardt, P V Ivashin, A Ya Tverdokhlebov, M M Krishtal

    Oxide layers formed by plasma electrolytic oxidation (PEO) on pre-eutectic aluminum-silicon alloy 361.0 (9.8 wt.% Si) at various current pulse frequencies (50, 500, and 1000 Hz) were investigated. Scanning electron microscopy (SEM), energy dispersive X-ray microanalysis (EDXMA), x-ray diffraction analysis (XRD) were applied for the investigation of the oxide layers. Thickness, roughness, microhardness, wear resistance and thermal conductivity of the obtained oxide layers were measured. It was found that at a forming current frequency of 500 Hz, the best productivity of forming of the oxide layer is achieved, and the layer has the best hardness and wear resistance, and the smallest roughness.