Eugeny D. Borgardt
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Eugeny D. Borgardt has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Anton V. Polunin
Togliatti State University, Togliatti, Russia
9 shared publications - Mikhail M. Krishtal
Togliatti State University, Togliatti, Russia
9 shared publications - Alisa O. Cheretaeva
Togliatti State University, Togliatti, Russia
4 shared publications - Marat R. Shafeev
Togliatti State University, Togliatti, Russia
4 shared publications - Alexander Katsman
Technion – Israel Institute of Technology
3 shared publications - Alyona G. Denisova
Togliatti State University
2 shared publications
Latest Publications
- 1 August 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 67 (4) , 475-502
The Mechanical and Corrosion Properties of Ceria-Reinforced PEO Coatings on Mg–RE Alloy
Limitations in the possibilities of using such interesting materials in terms of the ratio of density and volumetric mechanical characteristics as magnesium alloys with the addition of rare earth elements (Mg–RE), associated with the low corrosion properties of their surface, impose the need to search for and improve methods for its improvement. Of particular importance is the elimination of the phenomenon of microgalvanic corrosion that occurs at the interfaces between the phases of the alloy matrix (a-Mg) and secondary strengthening phases. The mechanical properties of the Mg–RE surface are also insufficient for work under contact conditions. In this research, the method of electrochemical formation of conversion protective ceramic layers—plasma electrolytic oxidation (PEO)—was modified by the addition of cerium dioxide particles CeO2 into the electrolyte at two modes (medium (250 Hz) and high (1000 Hz)) of technological pulse frequencies. It has been established that the mechanism of incorporation of dispersed particles of cerium dioxide consists of both electrophoretic incorporation of particles into the forming coating and thermokinetic inert incorporation as a result of impact interaction of particles and the oxide layer, and in both cases, preservation of CeO2 particles in its original state occurs. Modification of coatings with CeO2 particles allowed increasing resistance to chipping by up to 50 times and reduce the chip area during indentation from ~0.5 up to ~0.01 mm2, and the use of high-frequency PEO mode, in general, improves resistance to chipping by ~2–3 times, regardless of the concentration of CeO2 particles in the electrolyte compared to the mid-frequency. The CeO2 particles had greatest influence on the wear resistance of the oxide coating—high-frequency PEO with the addition of CeO2 allowed reducing the values of specific wear to ~0.05–0.1 µm/(N m) at high frequency PEO versus with ~0.3 µm/(N m) for the base coating obtained in mid-frequency PEO. Without the addition of particles, high-frequency PEO allowed reducing the wear of the base coating in the experiment by ~1.5 times compared to the medium-frequency one, which indicates the synergy of the interaction of the CeO2 additive and high-frequency PEO. Studies of the corrosion properties of coatings have shown that CeO2 particles slightly reduced the original characteristics, however, with prolonged exposure to a corrosive medium, some restoration of the corrosion properties of the coatings and the formation of a new corrosion-resistant phase in them—Mg0.667Al0.333(OH)2(CO3)0.167(H2O)0.5 (hydrotalcite)—is observed.
- 1 August 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 67 (4) , 475-502
The Mechanical and Corrosion Properties of Ceria-Reinforced PEO Coatings on Mg–RE Alloy
Limitations in the possibilities of using such interesting materials in terms of the ratio of density and volumetric mechanical characteristics as magnesium alloys with the addition of rare earth elements (Mg–RE), associated with the low corrosion properties of their surface, impose the need to search for and improve methods for its improvement. Of particular importance is the elimination of the phenomenon of microgalvanic corrosion that occurs at the interfaces between the phases of the alloy matrix (a-Mg) and secondary strengthening phases. The mechanical properties of the Mg–RE surface are also insufficient for work under contact conditions. In this research, the method of electrochemical formation of conversion protective ceramic layers—plasma electrolytic oxidation (PEO)—was modified by the addition of cerium dioxide particles CeO2 into the electrolyte at two modes (medium (250 Hz) and high (1000 Hz)) of technological pulse frequencies. It has been established that the mechanism of incorporation of dispersed particles of cerium dioxide consists of both electrophoretic incorporation of particles into the forming coating and thermokinetic inert incorporation as a result of impact interaction of particles and the oxide layer, and in both cases, preservation of CeO2 particles in its original state occurs. Modification of coatings with CeO2 particles allowed increasing resistance to chipping by up to 50 times and reduce the chip area during indentation from ~0.5 up to ~0.01 mm2, and the use of high-frequency PEO mode, in general, improves resistance to chipping by ~2–3 times, regardless of the concentration of CeO2 particles in the electrolyte compared to the mid-frequency. The CeO2 particles had greatest influence on the wear resistance of the oxide coating—high-frequency PEO with the addition of CeO2 allowed reducing the values of specific wear to ~0.05–0.1 µm/(N m) at high frequency PEO versus with ~0.3 µm/(N m) for the base coating obtained in mid-frequency PEO. Without the addition of particles, high-frequency PEO allowed reducing the wear of the base coating in the experiment by ~1.5 times compared to the medium-frequency one, which indicates the synergy of the interaction of the CeO2 additive and high-frequency PEO. Studies of the corrosion properties of coatings have shown that CeO2 particles slightly reduced the original characteristics, however, with prolonged exposure to a corrosive medium, some restoration of the corrosion properties of the coatings and the formation of a new corrosion-resistant phase in them—Mg0.667Al0.333(OH)2(CO3)0.167(H2O)0.5 (hydrotalcite)—is observed.
- 1 October 2025
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 66 (5) , 341-360
The Effect of Ceria Particles Incorporation on Protective Properties of Oxide Layers Formed by PEO on Mg Alloy with LPSO-Phase
The progress in the magnesium alloy design technology has enabled outstanding characteristics to be achieved for alloys containing both the strengthening LPSO phase (long-period stacking-ordered phase, LPSO) and rare earth elements (Mg–Gd–X, Mg–Nd–X, Mg–Y–X, Mg–Sc–X, and other systems): increase the allowable continuous service temperatures to ~250–300°C, the tensile strength to ~930 MPa, the relative elongation to ~30%, and the hardness to ~190 HV. However, the phenomenon of microgalvanic corrosion arising from the potential difference between the LPSO phase and the α-Mg matrix at their interface, as well as insufficient surface hardness, are the main problems of these alloys, necessitating surface modification for most applications. In this study, the plasma electrolytic oxidation (PEO) technology for treatment of light alloys was modified by adding cerium dioxide (CeO2) particles to the electrolyte in order to improve the characteristics of oxide layers formed on a Mg–Y–Zn–Yb–Zr alloy with the LPSO phase. The additive concentration (1–5 g/L, with a 1 g/L increment) and the forming pulse frequency of the process current (250 and 1000 Hz) were varied. Consequently, the high-frequency (1000 Hz) PEO with the addition of 4 g/L СeO2 to the electrolyte allowed the average microhardness to be increased from ~350 to ~690 MPa, i.e., by ~2 times, and the adhesion strength to be improved by 40% relative to the basic variant. The incorporation of CeO2 had a negligible effect on the corrosion resistance of the layers; the most pronounced positive effect was observed at a PEO frequency of 1000 Hz and at a CeO2 particle concentration of 1 g/L: the polarization resistance of the oxide layer was ~8.2 MΩ cm2, the corrosion current density was ~3.8 nA/cm2, and the impedance modulus was ~4.2 MΩ cm2 in comparison with the respective characteristics of ~4.3 MΩ cm2, ~9.8 nA/cm2, and ~3.0 MΩ cm2 for the basic oxide layer, which is due to the inert (no chemical reactions involved) incorporation of cerium oxide particles into the layer, its compacted structure, and reduced porosity.
- 1 October 2025
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 66 (5) , 341-360
The Effect of Ceria Particles Incorporation on Protective Properties of Oxide Layers Formed by PEO on Mg Alloy with LPSO-Phase
The progress in the magnesium alloy design technology has enabled outstanding characteristics to be achieved for alloys containing both the strengthening LPSO phase (long-period stacking-ordered phase, LPSO) and rare earth elements (Mg–Gd–X, Mg–Nd–X, Mg–Y–X, Mg–Sc–X, and other systems): increase the allowable continuous service temperatures to ~250–300°C, the tensile strength to ~930 MPa, the relative elongation to ~30%, and the hardness to ~190 HV. However, the phenomenon of microgalvanic corrosion arising from the potential difference between the LPSO phase and the α-Mg matrix at their interface, as well as insufficient surface hardness, are the main problems of these alloys, necessitating surface modification for most applications. In this study, the plasma electrolytic oxidation (PEO) technology for treatment of light alloys was modified by adding cerium dioxide (CeO2) particles to the electrolyte in order to improve the characteristics of oxide layers formed on a Mg–Y–Zn–Yb–Zr alloy with the LPSO phase. The additive concentration (1–5 g/L, with a 1 g/L increment) and the forming pulse frequency of the process current (250 and 1000 Hz) were varied. Consequently, the high-frequency (1000 Hz) PEO with the addition of 4 g/L СeO2 to the electrolyte allowed the average microhardness to be increased from ~350 to ~690 MPa, i.e., by ~2 times, and the adhesion strength to be improved by 40% relative to the basic variant. The incorporation of CeO2 had a negligible effect on the corrosion resistance of the layers; the most pronounced positive effect was observed at a PEO frequency of 1000 Hz and at a CeO2 particle concentration of 1 g/L: the polarization resistance of the oxide layer was ~8.2 MΩ cm2, the corrosion current density was ~3.8 nA/cm2, and the impedance modulus was ~4.2 MΩ cm2 in comparison with the respective characteristics of ~4.3 MΩ cm2, ~9.8 nA/cm2, and ~3.0 MΩ cm2 for the basic oxide layer, which is due to the inert (no chemical reactions involved) incorporation of cerium oxide particles into the layer, its compacted structure, and reduced porosity.
- Open Access
- 29 May 2023
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 10 (2) , 202310212
Improvement of protective oxide layers formed by high-frequency plasma electrolytic oxidation on Mg-RE alloy with LPSO-phase
Oxide layers on Mg97Y2Zn1 magnesium alloy with strengthening LPSO-phase were formed by plasma electrolytic oxidation (PEO) in bipolar mode with frequency variation of forming current pulses (50 and 500 Hz) and addition of sodium aluminate or sodium silicate to alkali phosphate fluoride electrolyte. Microstructure, chemical and phase composition, corrosion and mechanical properties of the oxide layers formed were investigated. With increasing current frequency for both electrolytes, an increase in homogeneity of the oxide layers structure and a decrease in their porosity and fracturing at constant thickness were recorded. The oxide layers formed at 500 Hz even with some decrease in hardness have better adhesive strength and 2 orders of magnitude higher short-term corrosion resistance values. PEO of Mg-alloy with LPSO-phase in the electrolyte with addition of sodium aluminate in combination with increased pulse frequency (500 Hz) allows forming the best-quality uniform oxide layer with high hardness, adhesive strength and corrosion resistance properties. The use of electrolyte with addition of sodium silicate reduced the adhesive strength by 1.5 times and brought down the long-term corrosion resistance of oxide layers by an order of magnitude, as compared with the electrolyte with sodium aluminate. The reason for a significant improvement in the complex of protective properties of the oxide layers with an increase in the current pulse frequency is supposed to be a decrease in the power and duration of individual microarc discharges with simultaneous increase in their number per unit oxidized area.
- 29 May 2023
- Published by Ural Federal University in Chimica Techno Acta
- Vol. 10 (2) , 202310212
Open AccessImprovement of protective oxide layers formed by high-frequency plasma electrolytic oxidation on Mg-RE alloy with LPSO-phase
Oxide layers on Mg97Y2Zn1 magnesium alloy with strengthening LPSO-phase were formed by plasma electrolytic oxidation (PEO) in bipolar mode with frequency variation of forming current pulses (50 and 500 Hz) and addition of sodium aluminate or sodium silicate to alkali phosphate fluoride electrolyte. Microstructure, chemical and phase composition, corrosion and mechanical properties of the oxide layers formed were investigated. With increasing current frequency for both electrolytes, an increase in homogeneity of the oxide layers structure and a decrease in their porosity and fracturing at constant thickness were recorded. The oxide layers formed at 500 Hz even with some decrease in hardness have better adhesive strength and 2 orders of magnitude higher short-term corrosion resistance values. PEO of Mg-alloy with LPSO-phase in the electrolyte with addition of sodium aluminate in combination with increased pulse frequency (500 Hz) allows forming the best-quality uniform oxide layer with high hardness, adhesive strength and corrosion resistance properties. The use of electrolyte with addition of sodium silicate reduced the adhesive strength by 1.5 times and brought down the long-term corrosion resistance of oxide layers by an order of magnitude, as compared with the electrolyte with sodium aluminate. The reason for a significant improvement in the complex of protective properties of the oxide layers with an increase in the current pulse frequency is supposed to be a decrease in the power and duration of individual microarc discharges with simultaneous increase in their number per unit oxidized area.
- Open Access
- 1 December 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2144 (1) , 012009
Effect of TiN particles on mechanical and anticorrosive properties of oxide layers formed by PEO on silumin
The work focuses on the effect of sub-micron and micron dispersity titanium nitride additions to the electrolyte during plasma electrolytic oxidation (PEO) of silumin A14130(11.5 wt% Si) on the structure, mechanical and anticorrosive properties of the oxide layers. It was found that the greatest positive effect of sub-micron TiN particles on the hardness and wear resistance of oxide layers is achieved at concentrations in the range of 1.0–2.5 g/l, and for micron TiN particles – at 0.5–1.0 g/l concentrations. However, for all concentrations of TiN particles, their insertion into the oxide layer has adverse effect on the anticorrosive properties of the oxide layer.
- 1 December 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2144 (1) , 012009
Open AccessEffect of TiN particles on mechanical and anticorrosive properties of oxide layers formed by PEO on silumin
The work focuses on the effect of sub-micron and micron dispersity titanium nitride additions to the electrolyte during plasma electrolytic oxidation (PEO) of silumin A14130(11.5 wt% Si) on the structure, mechanical and anticorrosive properties of the oxide layers. It was found that the greatest positive effect of sub-micron TiN particles on the hardness and wear resistance of oxide layers is achieved at concentrations in the range of 1.0–2.5 g/l, and for micron TiN particles – at 0.5–1.0 g/l concentrations. However, for all concentrations of TiN particles, their insertion into the oxide layer has adverse effect on the anticorrosive properties of the oxide layer.
- Open Access
- 1 December 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2144 (1) , 012018
The effect of process current parameters on the properties of oxide layers under plasma electrolytic oxidation of AMg6 alloy
The effect of current density and current ratio in the cathodic and anodic half-cycles during prolonged (180 minutes) plasma electrolytic oxidation (PEO) of AMg6 wrought alloy on the oxide layer wear and corrosion resistance were studied. It was established that the best wear resistance is achieved in the oxide layers obtained in the “soft sparking” mode (negative-to-positive pulse ratios of 1.15–1.30) at current densities of 9–15 A dm−2, and the best set of wear resistance and corrosion resistance – in the oxide layers obtained in “symmetrical” mode (negative-to-positive pulse ratio of 1.00).
- 1 December 2021
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 2144 (1) , 012018
Open AccessThe effect of process current parameters on the properties of oxide layers under plasma electrolytic oxidation of AMg6 alloy
The effect of current density and current ratio in the cathodic and anodic half-cycles during prolonged (180 minutes) plasma electrolytic oxidation (PEO) of AMg6 wrought alloy on the oxide layer wear and corrosion resistance were studied. It was established that the best wear resistance is achieved in the oxide layers obtained in the “soft sparking” mode (negative-to-positive pulse ratios of 1.15–1.30) at current densities of 9–15 A dm−2, and the best set of wear resistance and corrosion resistance – in the oxide layers obtained in “symmetrical” mode (negative-to-positive pulse ratio of 1.00).
- Open Access
- 26 November 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1121 (1) , 012014
The influence of SiO2 nanoparticles addition into electrolyte on the thermal conductivity of oxide layer formed on eutectic aluminum-silicon alloy by PEO
Oxide layers formed by plasma electrolytic oxidation with SiO2 nanoparticles addition into electrolyte on eutectic aluminum-silicon alloy were investigated by scanning electronic microscopy (SEM), energy dispersive X-ray microanalysis (EDXMA) and X-ray diffraction (XRD) analysis. The thermal conductivity of oxide layers was measured by constant heat flow method. Obtained values of the thermal conductivity of oxide layers are significantly smaller than the values of oxide layer components as bulk materials. Decreasing of thermal conductivity of oxide layer in ratio of two is observed if SiO2 nanoparticles are added into electrolyte. It is shown that the sedimentation of nanoparticles into oxide layer and decreasing of crystalline sizes are the reasons of decreasing of thermal conductivity.
- 26 November 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1121 (1) , 012014
Open AccessThe influence of SiO2 nanoparticles addition into electrolyte on the thermal conductivity of oxide layer formed on eutectic aluminum-silicon alloy by PEO
Oxide layers formed by plasma electrolytic oxidation with SiO2 nanoparticles addition into electrolyte on eutectic aluminum-silicon alloy were investigated by scanning electronic microscopy (SEM), energy dispersive X-ray microanalysis (EDXMA) and X-ray diffraction (XRD) analysis. The thermal conductivity of oxide layers was measured by constant heat flow method. Obtained values of the thermal conductivity of oxide layers are significantly smaller than the values of oxide layer components as bulk materials. Decreasing of thermal conductivity of oxide layer in ratio of two is observed if SiO2 nanoparticles are added into electrolyte. It is shown that the sedimentation of nanoparticles into oxide layer and decreasing of crystalline sizes are the reasons of decreasing of thermal conductivity.
- Open Access
- 26 November 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1121 (1) , 012025
The influence of SiO2 nanoparticles addition into electrolyte on the wear resistance of oxide layers formed by PEO on aluminum-silicon alloy
Scanning electron microscopy, X-ray spectral microanalysis, X-ray diffraction analysis, and instrumental indentation were used for studying of oxide layers formed by plasma electrolytic oxidation (PEO) on the eutectic aluminum-silicone alloy A04130 in electrolyte with the addition of SiO2 nanoparticles of different concentrations. The optimum concentration of SiO2 nanoparticles in the electrolyte (3 g/l) was found, for achieving maximum microhardness and wear resistance of the oxide layer, exceeding the value obtained in the electrolyte without adding SiO2 nanoparticles by 1.6 and 3.5 times, respectively.
- 26 November 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1121 (1) , 012025
Open AccessThe influence of SiO2 nanoparticles addition into electrolyte on the wear resistance of oxide layers formed by PEO on aluminum-silicon alloy
Scanning electron microscopy, X-ray spectral microanalysis, X-ray diffraction analysis, and instrumental indentation were used for studying of oxide layers formed by plasma electrolytic oxidation (PEO) on the eutectic aluminum-silicone alloy A04130 in electrolyte with the addition of SiO2 nanoparticles of different concentrations. The optimum concentration of SiO2 nanoparticles in the electrolyte (3 g/l) was found, for achieving maximum microhardness and wear resistance of the oxide layer, exceeding the value obtained in the electrolyte without adding SiO2 nanoparticles by 1.6 and 3.5 times, respectively.
- 1 April 2016
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2016 (4) , 385-388
Wear resistance of the oxide layers formed on AK9pch silumin by microarc oxidation in an electrolyte modified by silicon dioxide nanoparticles
- 1 April 2016
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2016 (4) , 385-388
Wear resistance of the oxide layers formed on AK9pch silumin by microarc oxidation in an electrolyte modified by silicon dioxide nanoparticles