KMKumar Murugesan

Kumar Murugesan

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Kumar Murugesan has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Investigation on geometric, dimensional accuracy and surface roughness for 3D printed PLA via fused deposition modelling (FDM) process

    by N. Jayakumar, G. Senthilkumar, M. Kumar

    Fused deposition modeling (FDM) is an advanced additive manufacturing technique known for its precision and repeatability, extensively applied in producing automotive and industrial components. This study employs the Taguchi L 9 orthogonal array (OA) approach to optimize process parameters for minimizing dimensional inaccuracies, geometric deviations, and surface roughness (Ra) in polylactic acid (PLA) specimens fabricated as per ASTM D638 Type V standards. Four critical printing parameters: extrusion temperature (ET), infill pattern (Ip), print rate (Rp), and layer height (LH) are investigated, focusing on specimen thickness (Ts), width of the grip section (Wgs), overall length (OL), circularity (Circ), cylindricity (Cyl), surface roughness (Ra), and waviness (Wa). Signal-to-noise (S/N) ratio analysis identified optimal parameter combinations, revealing that Ip, ET, and Rp significantly influence circularity by 39.24%, 37.34%, and 15.19%, respectively. One of the important factors that affect the degree of inaccuracy in cylindricity is the Ip. Gyroid pattern generated the least amount of inaccuracy out of all the patterns that were tested. Layer height (LH) at 0.1 mm was the most critical factor affecting Ra and Wa, while an extrusion temperature of 215°C predominantly influenced Ts. The Ip has the most affected the grip section width. In contrast to expectation, the triangle Ip achieved the minimum width error that was 0.3384%. The Rp of 40 mm/s has the highest impact on the OL deviations. Out of all the other patterns, the Tri-Hexagon (Ip) has made the least contribution to the OL deviations. Rp exhibited a lower contribution to Ra (2.35%) and Wa (12.45%). The results demonstrate the effectiveness of the Taguchi approach in identifying optimal process setups for enhancing the precision, geometric accuracy, and surface quality of 3D-printed specimens.


  • Experimental research on friction and wear behavior of dissimilar steel composite structure developed by wire arc-DED process for an automobile brake rotor application

    by Kumar Murugesan, D Lenin Singaravelu, Ravikumar Krishnan, Manoj Maria Raj Palani

    Recent applications of dissimilar composite structures produced through the wire arc-direct energy deposition process are indispensable across various industries due to their lightweight hybrid components and superior mechanical and tribological properties. This process enables a novel way to fabricate of custom-designed, high-performance composite structures that optimize friction, wear resistance, and mechanical characteristics. The present study focuses on developing a dissimilar steel composite structure using wire arc additive manufacturing process, with tribological and microstructural investigations conducted to understand the interfacial wear properties of the alloys. Standardized specimens were prepared to assess their friction and wear behavior through pin-on-disc wear test-rig. Experimental results show that the composite specimens exhibit enhanced wear resistance even under extreme sliding conditions (50 N applied load and 2400 m sliding distance), with tribolayer formation confirmed through FESEM micrographs and EDAX analysis. The highest specific wear rate (SWR) (3.87E-04 mm³/Nm) was observed at 50 N, 6.28 m/s, and 1600 m sliding distance, with a friction coefficient of 0.26. Adhesive wear was identified as the dominant wear mechanism between the specimen and the counterpart. Taguchi's multiresponse optimization indicated that sliding distance had the most significant effect on SWR and friction coefficient, followed by applied load and sliding velocity.


  • Enhancing UV resistance of TiO2 reinforced Kevlar 29 fiber using Sol-Gel & Low-temperature Hydrothermal Processes

    by Naveen R, Kumar M

    Mechanical properties of Kevlar fibers are significantly affected by their chemical structure when they are subjected to ultraviolet (UV) environment owing to photo degradation effect. In this work, Kevlar fibers are modified by means of impregnating with the titanium dioxide (TiO2) using low temperature hydrothermal process and dip coating methods. Ultraviolet–visible absorption spectrum confirms that hydrothermal treated Kevlar fibers exhibited outstanding UV resistance among others. The UV durability of the TiO2 modified Kevlar fiber is carried out using accelerated photoageing method up to 180 hours. Results of the tensile test showed that the best tensile strength was demonstrated by the modified fiber.


  • Open Access

    A review on friction stir processing of Al6061 surface composites

    by M. Kumar, R. Prasanth, B. Selvakumar, V. Ranjith

    Friction Stir Processing (FSP), a solid state materials processing technique is employed to modify the microstructure and properties of surface which is based on the principles of Friction Stir Welding (FSW). FSP is one of the most promising techniques that produces surface composites. As of now, FSP has been widely used for producing surface composites using more of aluminium, magnesium and copper alloys. FSP enhances the mechanical properties like tensile strength, hardness, ductility and fatigue and also tribological properties like wear resistance. It also eliminates the defects that are produced in the matrix alloy during casting process and reduces distortion. Most of the Severe Plastic Deformation (SPD) techniques changes the bulk properties of the material but FSP does not change the bulk properties, instead, grain size refinement can be achieved due to input heat that emerges from friction. This article covers the investigations carried out on the influence of the process parameters and tool characteristics, on the mechanical and tribological properties of Al6061 based surface composites synthesized by friction stir processing.


  • Tribological characterization of Al6061/alumina/graphite/redmud hybrid composite for brake rotor application

    by M. Kumar, A. Megalingam

    Dry sliding tribological characterization of redmud particle-reinforced Al6061/alumina/graphite hybrid metal matrix composite (RM-AlHMMC) was investigated as per ASTM G99-05 using pin on disc experimental setup. Initially, hybrid composites were fabricated through stir casting process by varying the wt.% of redmud particle as 3, 7, and 11, and then the wear tests were carried out based on L27 orthogonal array. The experimental results revealed that 11 wt.% RM-AlHMMC showed maximum of 90% improved wear resistance than AlHMMC. For all the composites, the coefficient of friction (CoF) increases and saturates with the applied load and sliding distance, in which 11 wt.% RM-AlHMMC showed maximum of 48% increased CoF than AlHMMC. Metallographic investigation of worn-out AlHMMC composite showed that at maximum applied load, sliding velocity, and sliding distance, the wear mechanism changes from abrasive to adhesive, but adding of redmud particle showed combined adhesive and abrasive wear mechanisms. The optimized tribological parameters were obtained using grey relational analysis which revealed that 11 wt.% RM-AlHMMC has improved tribological properties.


  • Effect of sliding distance on dry sliding tribological behaviour of Aluminium Hybrid Metal Matrix Composite (AlHMMC): An alternate for automobile brake rotor – A Grey Relational approach

    by M Kumar, Megalingam Murugan A, V Baskaran, Ks Hanumanth Ramji

    In fact, aluminium alloys have impressive mechanical and physical properties which make them robust for number of automobile applications. Reinforcing hard ceramic particles and solid lubricants with aluminium alloys gives balanced mechanical, physical and tribological characteristics for cast composites. The effect of sliding distance on tribological behaviour of Al6061-T6 alloy and its composite reinforced with hard ceramic constituent alumina (3 wt.%) and solid lubricant graphite (3 wt.%) fabricated through stir casting technique is discussed in this work. The American Society for Testing of Materials-G99-95 standard specimens prepared from cast composites are supposed to dry slide on the steel disc of a pin-on-disc apparatus. It is observed from the results that, for all combinations of applied load, sliding velocity and sliding distance aluminium hybrid metal matrix composite (AlHMMC) reveal superior tribological properties than the Al6061 alloy. Experimental wear test results exhibit an increasing trend of specific wear rate of AlHMMC for increasing load and sliding distance which is absolutely lesser than Al6061 alloy. However, the impact of sliding velocity evident decrease in specific wear rate upto 4.18 m/s later it starts increasing with increase in sliding distance. The worn-out specimen surfaces are examined for their elemental, compound characterization and morphological analysis through energy dispersive X-ray detector spectroscopy and scanning electron microscope, respectively. Optimized process parameters are obtained by grey optimization approach which yields improved specific wear resistance and coefficient of friction. Improved results of hybrid composite offers an assurance to alternate existing cast iron brake rotor for the future.