Alexander Diem
Research Subjects
Alexander Diem has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Igor Velkavrh
V-Research GmbH
6 shared publications - Florian Ausserer
V-Research GmbH, Stadtstrasse 33, 6850 Dornbirn, Austria
4 shared publications - Joel Voyer
V-Research GmbH, Stadtstrasse 33, 6850 Dornbirn, Austria
4 shared publications - Stefan Klien
V-Research GmbH, Stadtstrasse 33, 6850 Dornbirn, Austria
3 shared publications Stefan Klien
V-Research GmbH, 6850 Dornbirn, Austria
2 shared publications- Wolfgang Tillmann
Institute of Materials Engineering, TU Dortmund University, Leonhard-Euler-Strasse 2, 44227 Dortmund, Germany
2 shared publications
Latest Publications
- Open Access
- 16 February 2019
- Published by MDPI AG in Lubricants
- Vol. 7 (2) , 17
Static and Dynamic Friction of Pure and Friction-Modified PA6 Polymers in Contact with Steel Surfaces: Influence of Surface Roughness and Environmental Conditions
In the present study, PA6 polymers with and without solid lubricant inclusions were investigated against S1100QL steel surfaces that had different surface roughness values—a very high surface roughness (Rz ≈ 40 µm) and a low surface roughness (Rz ≈ 5 µm). Static and dynamic friction coefficients were analysed under a series of nominal contact pressures (2.5 to 40 N/mm2) considering the influences of polymer water saturation, temperature, counter-body surface roughness and lubrication. Mechanisms for the observed influences of the respective parameters are provided and are interpreted from the view of the adhesive and deformative contributions to the friction force.
- 16 February 2019
- Published by MDPI AG in Lubricants
- Vol. 7 (2) , 17
Open AccessStatic and Dynamic Friction of Pure and Friction-Modified PA6 Polymers in Contact with Steel Surfaces: Influence of Surface Roughness and Environmental Conditions
In the present study, PA6 polymers with and without solid lubricant inclusions were investigated against S1100QL steel surfaces that had different surface roughness values—a very high surface roughness (Rz ≈ 40 µm) and a low surface roughness (Rz ≈ 5 µm). Static and dynamic friction coefficients were analysed under a series of nominal contact pressures (2.5 to 40 N/mm2) considering the influences of polymer water saturation, temperature, counter-body surface roughness and lubrication. Mechanisms for the observed influences of the respective parameters are provided and are interpreted from the view of the adhesive and deformative contributions to the friction force.
- Open Access
- 28 April 2018
- Published by MDPI AG in Lubricants
- Vol. 6 (2) , 42
Development of a Constitutive Model for Friction in Bulk Metal Forming
This paper presents a systematic procedure for the development of a constitutive model of friction with focus on the application in bulk metal forming simulations. The empirically based friction model describes friction as a function of sliding distance and the most relevant friction influencing parameters. The latter were determined by means of designed experiments. An optimal friction model is obtained as a trade-off between model accuracy and complexity by using stepwise nonlinear regression and a modified version of the Akaike information criterion. Within this study, the procedure is applied to determine a friction model for tube drawing. However, the same approach can also be used for modeling friction of any other bulk metal forming process.
- 28 April 2018
- Published by MDPI AG in Lubricants
- Vol. 6 (2) , 42
Open AccessDevelopment of a Constitutive Model for Friction in Bulk Metal Forming
This paper presents a systematic procedure for the development of a constitutive model of friction with focus on the application in bulk metal forming simulations. The empirically based friction model describes friction as a function of sliding distance and the most relevant friction influencing parameters. The latter were determined by means of designed experiments. An optimal friction model is obtained as a trade-off between model accuracy and complexity by using stepwise nonlinear regression and a modified version of the Akaike information criterion. Within this study, the procedure is applied to determine a friction model for tube drawing. However, the same approach can also be used for modeling friction of any other bulk metal forming process.
- Open Access
- 16 November 2017
- Published by MDPI AG in Lubricants
- Vol. 5 (4) , 45
Reduction of the Adhesive Friction of Elastomers through Laser Texturing of Injection Molds
It is well known that elastomers usually possess poor dry sliding friction properties due to their highly adhesive character. In order to overcome this problematic behavior in industrial applications, interfacial materials such as oils, greases, coatings, or lacks are normally used in order to separate or to functionalize the contact surfaces of elastomers. Alternatively, the high adhesion tendency of elastomers may be explicitly reduced by modifying the elastomer composition itself or by enabling a reduction of its effective contact area through, for example, surface laser texturing. This second approach, i.e., the reduction of the adhesive character of elastomers through laser structuring, will be the main topic of the present study. For this purpose, different micro-sized grooved structures were produced on flat injection molds using an ultra-short pulsed laser. The micro-structured molds were then used to produce injection molded micro-ridged Liquid Silicone Rubber (LSR) sample pads. The investigations consisted firstly of determining the degree of replication of the mold micro-structures onto the surface of the LSR pads and secondly, to ascertain the degree of reduction of the friction force (or coefficient of friction) of these micro-ridged LSR pads in comparison to the benchmark (unstructured LSR pads) when tested under dry conditions against Aluminum alloy (Al-6082) or PA6.6-GF30 plates. For this second part of the investigation, the normal force (or contact pressure) dependency of the coefficient of friction was determined through stepwise load increasing friction tests. The results of these investigations have shown that the production of micro-ridged surfaces on LSR pads through laser structuring of the injection molds could be successfully achieved and that it enables a significant reduction of the friction force for low normal forces (or contact pressures), where the component of adhesion friction is playing an important and determining role in the overall friction behavior of the LSR elastomer.
- 16 November 2017
- Published by MDPI AG in Lubricants
- Vol. 5 (4) , 45
Open AccessReduction of the Adhesive Friction of Elastomers through Laser Texturing of Injection Molds
It is well known that elastomers usually possess poor dry sliding friction properties due to their highly adhesive character. In order to overcome this problematic behavior in industrial applications, interfacial materials such as oils, greases, coatings, or lacks are normally used in order to separate or to functionalize the contact surfaces of elastomers. Alternatively, the high adhesion tendency of elastomers may be explicitly reduced by modifying the elastomer composition itself or by enabling a reduction of its effective contact area through, for example, surface laser texturing. This second approach, i.e., the reduction of the adhesive character of elastomers through laser structuring, will be the main topic of the present study. For this purpose, different micro-sized grooved structures were produced on flat injection molds using an ultra-short pulsed laser. The micro-structured molds were then used to produce injection molded micro-ridged Liquid Silicone Rubber (LSR) sample pads. The investigations consisted firstly of determining the degree of replication of the mold micro-structures onto the surface of the LSR pads and secondly, to ascertain the degree of reduction of the friction force (or coefficient of friction) of these micro-ridged LSR pads in comparison to the benchmark (unstructured LSR pads) when tested under dry conditions against Aluminum alloy (Al-6082) or PA6.6-GF30 plates. For this second part of the investigation, the normal force (or contact pressure) dependency of the coefficient of friction was determined through stepwise load increasing friction tests. The results of these investigations have shown that the production of micro-ridged surfaces on LSR pads through laser structuring of the injection molds could be successfully achieved and that it enables a significant reduction of the friction force for low normal forces (or contact pressures), where the component of adhesion friction is playing an important and determining role in the overall friction behavior of the LSR elastomer.
- 1 October 2017
- Published by Elsevier in Tribology International
- Vol. 114, 418-428
Using a standard pin-on-disc tribometer to analyse friction in a metal forming process
- 1 October 2017
- Published by Elsevier in Tribology International
- Vol. 114, 418-428
Using a standard pin-on-disc tribometer to analyse friction in a metal forming process
- 1 November 2014
- Published by Elsevier in Tribology International
- Vol. 79, 99-110
The effect of gaseous atmospheres on friction and wear of steel–steel contacts
- 1 November 2014
- Published by Elsevier in Tribology International
- Vol. 79, 99-110
The effect of gaseous atmospheres on friction and wear of steel–steel contacts
- 1 September 2010
- Published by Springer Nature in BHM Berg- und Hüttenmännische Monatshefte
- Vol. 155 (9) , 430-436
Verschleißeigenschaften salzbadnitrocarburierter Oberflächen verschiedener Badvarianten
- 1 September 2010
- Published by Springer Nature in BHM Berg- und Hüttenmännische Monatshefte
- Vol. 155 (9) , 430-436
Verschleißeigenschaften salzbadnitrocarburierter Oberflächen verschiedener Badvarianten