Marc Rébillat
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Marc Rébillat has a total of 105 co-authors. Here are the top co-authors by number of shared publications:
- Nazih Mechbal
Arts et Metiers ParisTech, PIMM UMR CNRS, Paris, France
31 shared publications Nazih Mechbal
Laboratoire Procédés et Ingénierie en Mécanique et Matériaux, École Nationale Supérieure d’Arts et Métiers, Paris, France
8 shared publicationsMikhail Guskov
5 shared publications- Pierre Margerit
Laboratoire Procédés et Ingénierie en Mécanique et Matériaux, PIMM, Arts et Métiers ParisTech 1 , UMR 8006, CNRS, CNAM, HESAM université, 151 boulevard de l’hôpital, 75013 Paris, France
4 shared publications - C. Fendzi
PIMM Laboratory, UMR CNRS 8006 Arts et Métiers ParisTech, France
3 shared publications - Cyril Nicard
PIMM1https://x.com/LabPimm/., CNAM / CNRS / Arts et Métiers Institute of Technology, Paris, France
3 shared publications
Latest Publications
- 5 November 2026
- Published by SAGE Publications in Structural Health Monitoring
Koopman operator models for self-reconfiguring vibration control and structural health monitoring
Active vibration control is widely implemented in flexible structural systems to maintain safe operating conditions under healthy states. Mechanical structures, however, are vulnerable to damage that alters mass, stiffness, or damping due to mechanisms such as cracks, delaminations, or loose connections. Such variations can significantly reduce the effectiveness of vibration control and may lead to system failure. Therefore, it is essential not only to monitor the system’s condition but also to update the control strategy to restore performance and re-establish the response characteristics of the undamaged state. This task is particularly challenging when relying solely on existing control instrumentation, which typically consists of a single actuator and sensor, and when the system’s physical properties change markedly before and after damage in both open- and closed-loop scenarios. This article introduces a novel approach that utilizes the Koopman operator to implement a real-time vibration control procedure with integrated structural health monitoring. The proposed method does not require prior knowledge of the structure’s physical model and can update the system representation online. Experimental validation is performed using a flexible cantilever beam equipped with three piezoelectric patches functioning as an actuator, a sensor, and a disturbance input. As a proof of concept, concentrated mass variations are introduced to simulate structural changes that affect the performance and reduce the effectiveness of vibration control. Different disturbance profiles are investigated, along with increasing mass removal. The results demonstrate that the proposed procedure can detect this structural variation, recompute the state-space model using the Koopman operator, update the controller, and ultimately enable self-reconfiguring behavior in the system.
- 5 November 2026
- Published by SAGE Publications in Structural Health Monitoring
Koopman operator models for self-reconfiguring vibration control and structural health monitoring
Active vibration control is widely implemented in flexible structural systems to maintain safe operating conditions under healthy states. Mechanical structures, however, are vulnerable to damage that alters mass, stiffness, or damping due to mechanisms such as cracks, delaminations, or loose connections. Such variations can significantly reduce the effectiveness of vibration control and may lead to system failure. Therefore, it is essential not only to monitor the system’s condition but also to update the control strategy to restore performance and re-establish the response characteristics of the undamaged state. This task is particularly challenging when relying solely on existing control instrumentation, which typically consists of a single actuator and sensor, and when the system’s physical properties change markedly before and after damage in both open- and closed-loop scenarios. This article introduces a novel approach that utilizes the Koopman operator to implement a real-time vibration control procedure with integrated structural health monitoring. The proposed method does not require prior knowledge of the structure’s physical model and can update the system representation online. Experimental validation is performed using a flexible cantilever beam equipped with three piezoelectric patches functioning as an actuator, a sensor, and a disturbance input. As a proof of concept, concentrated mass variations are introduced to simulate structural changes that affect the performance and reduce the effectiveness of vibration control. Different disturbance profiles are investigated, along with increasing mass removal. The results demonstrate that the proposed procedure can detect this structural variation, recompute the state-space model using the Koopman operator, update the controller, and ultimately enable self-reconfiguring behavior in the system.
- Open Access
- 12 October 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 213
In situ monitoring of the dismantling process of laminated composites by laser shock using ultrasonic guided waves
- 12 October 2026
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 213
Open AccessIn situ monitoring of the dismantling process of laminated composites by laser shock using ultrasonic guided waves
- Open Access
- 16 September 2026
- Published by Elsevier in Materials Chemistry and Physics: Sustainability and Energy
- Vol. 9
In-situ monitoring of μm-sized electrochemically generated corrosion damage and corrosion-fatigue cracks using ultrasonic Lamb waves
- 16 September 2026
- Published by Elsevier in Materials Chemistry and Physics: Sustainability and Energy
- Vol. 9
Open AccessIn-situ monitoring of μm-sized electrochemically generated corrosion damage and corrosion-fatigue cracks using ultrasonic Lamb waves
- Open Access
- 2 August 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of a viscoelastic layer on the propagation of Lamb waves
This work aims to propose a method for real-time monitoring of the rheological properties and thickness of a viscoelastic layer lying on an elastic plate using non-intrusive techniques, specifically Lamb waves emitted and received by a sparse network of piezoelectric transducers (PZT). Lamb waves are elastic guided waves in the thickness of a solid plate. They are adapted due to their sensitivity to the state of materials which cover the excited plate. The proposed methodological approach combines numerical and experimental techniques. Firstly a wave propagation model for the system is built in order to predict the dispersion of Lamb waves in the system that is considered as an isotropic solid plate loaded with a viscoelastic fluid layer on its top surface.{The effect of the rheological properties and thickness of the viscoelastic layer on the wavenumber, group velocity and attenuation is studied. Experimental wavenumber spectrums extracted from full-field data obtained via scanning velocimetry are then compared to the numerical predictions, validating the model for a range of calibrated viscous oils.A series of parametric studies were conducted using the validated model to follow the evolution of the thickness of the fluid and its viscosity and shear modulus. Finally, experiments using various configurations of viscoelastic loadings using a PZT network bonded under an aluminium plate were conducted to validate the relation found numerically between the evolution of rheological properties of the fluid layer and attenuation of Lamb waves. Tests using calibration oils and an epoxy resin during its curing phase were conducted in order to assess the accuracy of the model. The appearance of highly attenuated frequency domains depending on the properties of the viscoelastic layer confirmed that the use of Lamb waves is an appropriate tool in order to detect and characterize the material behaviour evolution of such a layer.
- 2 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of a viscoelastic layer on the propagation of Lamb waves
This work aims to propose a method for real-time monitoring of the rheological properties and thickness of a viscoelastic layer lying on an elastic plate using non-intrusive techniques, specifically Lamb waves emitted and received by a sparse network of piezoelectric transducers (PZT). Lamb waves are elastic guided waves in the thickness of a solid plate. They are adapted due to their sensitivity to the state of materials which cover the excited plate. The proposed methodological approach combines numerical and experimental techniques. Firstly a wave propagation model for the system is built in order to predict the dispersion of Lamb waves in the system that is considered as an isotropic solid plate loaded with a viscoelastic fluid layer on its top surface.{The effect of the rheological properties and thickness of the viscoelastic layer on the wavenumber, group velocity and attenuation is studied. Experimental wavenumber spectrums extracted from full-field data obtained via scanning velocimetry are then compared to the numerical predictions, validating the model for a range of calibrated viscous oils.A series of parametric studies were conducted using the validated model to follow the evolution of the thickness of the fluid and its viscosity and shear modulus. Finally, experiments using various configurations of viscoelastic loadings using a PZT network bonded under an aluminium plate were conducted to validate the relation found numerically between the evolution of rheological properties of the fluid layer and attenuation of Lamb waves. Tests using calibration oils and an epoxy resin during its curing phase were conducted in order to assess the accuracy of the model. The appearance of highly attenuated frequency domains depending on the properties of the viscoelastic layer confirmed that the use of Lamb waves is an appropriate tool in order to detect and characterize the material behaviour evolution of such a layer.
- Open Access
- 21 April 2026
- Published by Elsevier in SSRN Electronic Journal
Wideband characterization of additively manufactured viscoelastic materials
A unified framework dedicated to the characterization of viscoelastic materials over an extended range of frequencies is proposed. Three experimental methods are combined: (i) the Dynamic Mechanical Analysis associated with low frequencies; (ii) the ultrasound transmission technique allowing high frequency characterization; and (iii) the wavefield analysis bridging the medium frequency gap. The methodology is validated on quasi-homogeneous polymer composites obtained using multi-material additive manufacturing.As a result, the complete set of storage moduli and loss factors is provided from the quasi-static to the ultrasound regime, covering approximately 8 orders of magnitude in frequency (0.01 Hz -- 5 MHz). An extreme frequency-dependent behavior is observed for the softest material, with a storage modulus multiplied by nearly 1000 over the studied frequency spectrum and a loss factor reaching up to 100%. Unlike conventional approaches relying on the Time-Temperature-Superposition principle, this framework enables a direct estimation of the material behavior at the frequency of interest. This makes the proposed methodology an interesting candidate for the characterization of viscoelastic (meta-)materials with engineering applications spanning an extremely broad spectrum.
- 21 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessWideband characterization of additively manufactured viscoelastic materials
A unified framework dedicated to the characterization of viscoelastic materials over an extended range of frequencies is proposed. Three experimental methods are combined: (i) the Dynamic Mechanical Analysis associated with low frequencies; (ii) the ultrasound transmission technique allowing high frequency characterization; and (iii) the wavefield analysis bridging the medium frequency gap. The methodology is validated on quasi-homogeneous polymer composites obtained using multi-material additive manufacturing.As a result, the complete set of storage moduli and loss factors is provided from the quasi-static to the ultrasound regime, covering approximately 8 orders of magnitude in frequency (0.01 Hz -- 5 MHz). An extreme frequency-dependent behavior is observed for the softest material, with a storage modulus multiplied by nearly 1000 over the studied frequency spectrum and a loss factor reaching up to 100%. Unlike conventional approaches relying on the Time-Temperature-Superposition principle, this framework enables a direct estimation of the material behavior at the frequency of interest. This makes the proposed methodology an interesting candidate for the characterization of viscoelastic (meta-)materials with engineering applications spanning an extremely broad spectrum.
- Open Access
- 27 February 2026
- Published by Elsevier in SSRN Electronic Journal
In-situ monitoring of µm-sized electrochemically generated corrosion damage and corrosion-fatigue cracks using ultrasonic Lamb waves
Corrosion-induced damage and its progression into fatigue cracks poses significant challenges in the aeronautical industry, affecting both safety and maintenance costs. This study presents an integrated methodology combining electrochemical localized corrosion generation, cyclic fatigue loading, and in-situ monitoring using ultrasonic Lamb waves. A sparse array of piezoelectric transducers (PZTs) bonded to aluminium 2024-T3 specimens enables real-time damage tracking through ultrasonic-based Damage Index (DI) metrics, correlated with optical microscopic observations and electrochemical potential monitoring. The initiation and propagation of fatigue cracks from corrosion pits are successfully detected by characteristic oscillations in the open-circuit potential and changes in ultrasonic-based DI values. Post-mortem scanning electron microscopy (SEM) of fatigue striations refines crack front geometry estimation, allowing accurate stress intensity factor calculations, and determination of Paris law parameters consistent with literature data. Obtained results demonstrate the feasibility of real-time, non-destructive monitoring of corrosion-fatigue damages paving the way for cost-effective embedded structural health monitoring systems for aeronautical structures.
- 27 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIn-situ monitoring of µm-sized electrochemically generated corrosion damage and corrosion-fatigue cracks using ultrasonic Lamb waves
Corrosion-induced damage and its progression into fatigue cracks poses significant challenges in the aeronautical industry, affecting both safety and maintenance costs. This study presents an integrated methodology combining electrochemical localized corrosion generation, cyclic fatigue loading, and in-situ monitoring using ultrasonic Lamb waves. A sparse array of piezoelectric transducers (PZTs) bonded to aluminium 2024-T3 specimens enables real-time damage tracking through ultrasonic-based Damage Index (DI) metrics, correlated with optical microscopic observations and electrochemical potential monitoring. The initiation and propagation of fatigue cracks from corrosion pits are successfully detected by characteristic oscillations in the open-circuit potential and changes in ultrasonic-based DI values. Post-mortem scanning electron microscopy (SEM) of fatigue striations refines crack front geometry estimation, allowing accurate stress intensity factor calculations, and determination of Paris law parameters consistent with literature data. Obtained results demonstrate the feasibility of real-time, non-destructive monitoring of corrosion-fatigue damages paving the way for cost-effective embedded structural health monitoring systems for aeronautical structures.
- Open Access
- 1 February 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (2)
Interpretable AI for Guided-Wave SHM of Anisotropic Composites: Toward Trustworthy Damage Diagnosis
The use of Artificial Intelligence (AI) in Structural Health Monitoring (SHM) offers powerful capabilities for damage detection, localization, and quantification in complex composite structures. However, many data-driven models act as black boxes, providing limited interpretability and weak connection to the underlying wave physics. This work investigates a physics-guided AI framework based on dispersion-aware sparse decomposition and tensor analysis for guidedwave–based SHM. The approach combines compact, physically meaningful features—linked to propagation distance, attenuation, and dispersion—with machine learning to achieve efficient and interpretable decision-making. A comparative study is conducted against conventional data-driven approaches on a representative composite structure under various damage scenarios. Results show that while purely data driven models can achieve high detection accuracy, the proposed hybrid framework reaches acceptable performances with enhanced robustness and explainability. The physically grounded representation potentially allows direct insight into the damage mechanisms, enabling reliable monitoring and facilitating the integration of AI within maintenance and certification processes. This interpretable hybrid approach thus provides a promising route toward trustworthy, physics-informed SHM of next-generation aerostructures.
- 1 February 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (2)
Open AccessInterpretable AI for Guided-Wave SHM of Anisotropic Composites: Toward Trustworthy Damage Diagnosis
The use of Artificial Intelligence (AI) in Structural Health Monitoring (SHM) offers powerful capabilities for damage detection, localization, and quantification in complex composite structures. However, many data-driven models act as black boxes, providing limited interpretability and weak connection to the underlying wave physics. This work investigates a physics-guided AI framework based on dispersion-aware sparse decomposition and tensor analysis for guidedwave–based SHM. The approach combines compact, physically meaningful features—linked to propagation distance, attenuation, and dispersion—with machine learning to achieve efficient and interpretable decision-making. A comparative study is conducted against conventional data-driven approaches on a representative composite structure under various damage scenarios. Results show that while purely data driven models can achieve high detection accuracy, the proposed hybrid framework reaches acceptable performances with enhanced robustness and explainability. The physically grounded representation potentially allows direct insight into the damage mechanisms, enabling reliable monitoring and facilitating the integration of AI within maintenance and certification processes. This interpretable hybrid approach thus provides a promising route toward trustworthy, physics-informed SHM of next-generation aerostructures.
- Open Access
- 1 February 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (2)
Damage detection algorithm based on an innovative nonlinear model-order reduction technique: the Rank Reduction Autoencoder (RRAE) conditioned to learn damage features.
Structural Health Monitoring (SHM) aims to monitor in real-time the health state of engineering structures. For thin structures, Lamb Waves (LW) are very efficient for SHM purposes. A bonded piezoelectric transducer (PZT) emits LW in the structure in the form of a short tone burst. This initial wave packet (IWP) is then propagating in the structure and interacts with its boundaries and discontinuities, such as the presence of damage, generating additional waves packets. In this sense, both the geometry itself and the presence of damage can produce complex behaviors in the measured signal from sensors, which makes the extraction of features that will be used later to evaluate damage detection very complicated in complex scenarios. To solve this issue, here an innovative Deep Learning technique called Rank Reduction Autoencoder (RRAE) is considered. The RRAE consists on an autoencoder whose latent space is restricted to be expressed as a low-rank SVD approximation, capturing in this sense only the most important features of the studied signals, by keeping the advantage of learning complex behaviours by means of a nonlinear approximation. The novelty proposed in this work consists of adding an additional restriction in the latent space of the RRAE so that its content is as representative as possible to produce damage detection. This is achieved by means of a 2D Convolutional Neural Network (CNN) that takes as inputs the latent space and delivers as prediction the location of damage. Therefore, the training of the RRAE plus the extraction of important features by means of a MLP all together allows to obtain at convergence a powerful tool for damage detection in the SHM field. To illustrate the proposed technique, it is applied for the detection of damage on a thin plate.
- 1 February 2026
- Published by NDT.net GmbH & Co. KG in e-Journal of Nondestructive Testing
- Vol. 31 (2)
Open AccessDamage detection algorithm based on an innovative nonlinear model-order reduction technique: the Rank Reduction Autoencoder (RRAE) conditioned to learn damage features.
Structural Health Monitoring (SHM) aims to monitor in real-time the health state of engineering structures. For thin structures, Lamb Waves (LW) are very efficient for SHM purposes. A bonded piezoelectric transducer (PZT) emits LW in the structure in the form of a short tone burst. This initial wave packet (IWP) is then propagating in the structure and interacts with its boundaries and discontinuities, such as the presence of damage, generating additional waves packets. In this sense, both the geometry itself and the presence of damage can produce complex behaviors in the measured signal from sensors, which makes the extraction of features that will be used later to evaluate damage detection very complicated in complex scenarios. To solve this issue, here an innovative Deep Learning technique called Rank Reduction Autoencoder (RRAE) is considered. The RRAE consists on an autoencoder whose latent space is restricted to be expressed as a low-rank SVD approximation, capturing in this sense only the most important features of the studied signals, by keeping the advantage of learning complex behaviours by means of a nonlinear approximation. The novelty proposed in this work consists of adding an additional restriction in the latent space of the RRAE so that its content is as representative as possible to produce damage detection. This is achieved by means of a 2D Convolutional Neural Network (CNN) that takes as inputs the latent space and delivers as prediction the location of damage. Therefore, the training of the RRAE plus the extraction of important features by means of a MLP all together allows to obtain at convergence a powerful tool for damage detection in the SHM field. To illustrate the proposed technique, it is applied for the detection of damage on a thin plate.
- Open Access
SHM for Complex Composite Aerospace Structures: A Case Study on Engine Fan Blades
Composite engine fan blades are critical aircraft engine components, and their failure can compromise the safe and reliable operation of the entire aircraft. To enhance aircraft availability and safety within a condition-based maintenance framework, effective methods are needed to identify damage and monitor the blades’ condition throughout manufacturing and operation. This paper presents a unique experimental framework for real-time monitoring of composite engine blades utilizing state-of-the-art structural health monitoring (SHM) technologies, discussing the associated benefits and challenges. A case study is conducted on a representative Foreign Object Damage (FOD) panel, a substructure of a LEAP (Leading Edge Aviation Propulsion) engine fan blade, which is a curved, 3D-woven Carbon Fiber Reinforced Polymer (CFRP) panel with a secondary bonded steel leading edge. The loading scheme involves incrementally increasing, cyclic 4-point bending (loading–unloading) to induce controlled damage growth, simulating in-operation conditions and allowing evaluation of flexural properties before and after degradation. External damage, simulating foreign object impact common during flight, is introduced using a drop tower apparatus either before or during testing. The panel’s condition is monitored in-situ and in real time by two types of SHM sensors: screen-printed piezoelectric sensors for guided ultrasonic wave propagation studies and surface-bonded Fiber Bragg Grating (FBG) strain sensors. Experiments are conducted until panel collapse, and degradation is quantified by the reduction in initial stiffness, derived from the experimental load-displacement curves. This paper aims to demonstrate this unique experimental setup and the resulting SHM data, highlighting both the potential and challenges of this SHM framework for monitoring complex composite structures, while an attempt is made at correlating SHM data with structural degradation.
Open AccessSHM for Complex Composite Aerospace Structures: A Case Study on Engine Fan Blades
Composite engine fan blades are critical aircraft engine components, and their failure can compromise the safe and reliable operation of the entire aircraft. To enhance aircraft availability and safety within a condition-based maintenance framework, effective methods are needed to identify damage and monitor the blades’ condition throughout manufacturing and operation. This paper presents a unique experimental framework for real-time monitoring of composite engine blades utilizing state-of-the-art structural health monitoring (SHM) technologies, discussing the associated benefits and challenges. A case study is conducted on a representative Foreign Object Damage (FOD) panel, a substructure of a LEAP (Leading Edge Aviation Propulsion) engine fan blade, which is a curved, 3D-woven Carbon Fiber Reinforced Polymer (CFRP) panel with a secondary bonded steel leading edge. The loading scheme involves incrementally increasing, cyclic 4-point bending (loading–unloading) to induce controlled damage growth, simulating in-operation conditions and allowing evaluation of flexural properties before and after degradation. External damage, simulating foreign object impact common during flight, is introduced using a drop tower apparatus either before or during testing. The panel’s condition is monitored in-situ and in real time by two types of SHM sensors: screen-printed piezoelectric sensors for guided ultrasonic wave propagation studies and surface-bonded Fiber Bragg Grating (FBG) strain sensors. Experiments are conducted until panel collapse, and degradation is quantified by the reduction in initial stiffness, derived from the experimental load-displacement curves. This paper aims to demonstrate this unique experimental setup and the resulting SHM data, highlighting both the potential and challenges of this SHM framework for monitoring complex composite structures, while an attempt is made at correlating SHM data with structural degradation.