Giovanni Paolo Romano
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giovanni Paolo Romano has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
- Giorgio Moscato
Department Mechanical & Aerospace Engineering, University La Sapienza, 00184 Roma, Italy
4 shared publications - Giorgia Sinibaldi
Department of Mechanical and Aerospace Engineering, Sapienza University of Rome, Via Eudossiana 18, 00186 Roma, Italy
3 shared publications Giorgio Moscato
University of Rome “Sapienza”, via Eudossiana 18, Rome 00184, Italy
3 shared publications- Alessandro Capone
CNR-Institute of Marine Engineering, Via di Vallerano 139, 00128 Rome, Italy
2 shared publications Jais Mohamed
2 shared publicationsA. Lago
1 shared publication
Latest Publications
- Open Access
RoDaVi – a mixed drag-lift wind turbine: experimental investigation on performances and flows
- Open Access
- 14 September 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (9) , 553
Biomimetic Wings for Micro Air Vehicles
In this work, micro air vehicles (MAVs) equipped with bio-inspired wings are investigated experimentally in wind tunnel. The starting point is that insects such as dragonflies, butterflies and locusts have wings with rigid tubular elements (corrugation) connected by flexible parts (profiling). So far, it is important to understand the specific aerodynamic effects of corrugation and profiling as applied to conventional wings for the optimization of low-Reynolds-number aerodynamics. The present study, in comparison to previous investigations on the topic, considers whole MAVs rather than isolated wings. A planform with a low aperture-to-chord ratio is employed in order to investigate the interaction between large tip vortices and the flow over the wing surface at large angles of incidence. Comparisons are made by measuring global aerodynamic loads using force balance, specifically drag and lift, and detailed local velocity fields over wing surfaces, by means of particle image velocimetry (PIV). This type of combined global–local investigation allows describing and relating overall MAV performance to detailed high-resolution flow fields. The results indicate that the combination of wing corrugation and profiling gives effective enhancements in performance, around 50%, in comparison to the classical flat-plate configuration. These results are particularly relevant in the framework of low-aspect-ratio MAVs, undergoing beneficial interactions between tip vortices and large-scale separation.
- 14 September 2024
- Published by MDPI AG in Biomimetics
- Vol. 9 (9) , 553
Open AccessBiomimetic Wings for Micro Air Vehicles
In this work, micro air vehicles (MAVs) equipped with bio-inspired wings are investigated experimentally in wind tunnel. The starting point is that insects such as dragonflies, butterflies and locusts have wings with rigid tubular elements (corrugation) connected by flexible parts (profiling). So far, it is important to understand the specific aerodynamic effects of corrugation and profiling as applied to conventional wings for the optimization of low-Reynolds-number aerodynamics. The present study, in comparison to previous investigations on the topic, considers whole MAVs rather than isolated wings. A planform with a low aperture-to-chord ratio is employed in order to investigate the interaction between large tip vortices and the flow over the wing surface at large angles of incidence. Comparisons are made by measuring global aerodynamic loads using force balance, specifically drag and lift, and detailed local velocity fields over wing surfaces, by means of particle image velocimetry (PIV). This type of combined global–local investigation allows describing and relating overall MAV performance to detailed high-resolution flow fields. The results indicate that the combination of wing corrugation and profiling gives effective enhancements in performance, around 50%, in comparison to the classical flat-plate configuration. These results are particularly relevant in the framework of low-aspect-ratio MAVs, undergoing beneficial interactions between tip vortices and large-scale separation.
- Open Access
- 13 August 2024
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 160
Aerodynamic performances and near wake of an Ahmed body under unsteady flow conditions
- 13 August 2024
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 160
Open AccessAerodynamic performances and near wake of an Ahmed body under unsteady flow conditions
- Open Access
- 21 June 2024
- Published by Elsevier in International Journal of Thermofluids
- Vol. 23
Experimental investigation on a microfluidic U-turn channel for heat transfer applications
- 21 June 2024
- Published by Elsevier in International Journal of Thermofluids
- Vol. 23
Open AccessExperimental investigation on a microfluidic U-turn channel for heat transfer applications
- 1 January 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (1) , 013332
Role of density ratio on particle dispersion in a turbulent jet
The behavior of dispersed particles in a turbulent round jet is experimentally investigated. The role of particle-to-fluid density ratio is analyzed by inspecting particle velocity fields and preferential concentration at four different ratios, from 0.7 to 19.3. The jet near-field region, i.e., up to , is analyzed and compared to the unladen case. Particle-to-fluid density ratio is reported to have a strong impact on particle velocity field structure, in terms of jet transition and self-similar region as well as on turbulent fluctuations. Concentrations of particles show that increasing particle density corresponds to larger departure from uniformity. This occurrence is limited to the region , where also the largest differences of average and fluctuating velocities with respect to the unladen case are measured.- 1 January 2023
- Published by AIP Publishing in Physics of Fluids
- Vol. 35 (1) , 013332
Role of density ratio on particle dispersion in a turbulent jet
The behavior of dispersed particles in a turbulent round jet is experimentally investigated. The role of particle-to-fluid density ratio is analyzed by inspecting particle velocity fields and preferential concentration at four different ratios, from 0.7 to 19.3. The jet near-field region, i.e., up to , is analyzed and compared to the unladen case. Particle-to-fluid density ratio is reported to have a strong impact on particle velocity field structure, in terms of jet transition and self-similar region as well as on turbulent fluctuations. Concentrations of particles show that increasing particle density corresponds to larger departure from uniformity. This occurrence is limited to the region , where also the largest differences of average and fluctuating velocities with respect to the unladen case are measured.- Open Access
- 30 August 2022
- Published by Springer Nature in Experiments in Fluids
- Vol. 63 (9) , 1-18
Improving performances of biomimetic wings with leading-edge tubercles
The present study aims investigating experimentally wing/blade geometries in which the leading edge is modified by the presence of artificial bumps, following examples in nature (“biomimetics”). Specifically, the tubercles observed in humpback whales are considered with a special focus on easy manufacturing and performance improvements, trying to overcome the observed lift coefficient reduction before stall in comparison with a standard wing. To this end, different tubercle geometries are tested, by measuring overall forces acting on the wings and by deriving detailed velocity fields using particle image velocimetry. Measurements indicate performance improvements for all trailing edge tubercle geometries here tested. In addition, the detailed analysis of mechanisms underlying the improvement of performances suggests that a triangular shape of the leading edge combines the advantages of easy manufacturing and improvements of pre-stall behaviour. So far, a simple mathematical model, describing tubercles as delta wings, is presented and verified by experimental data. The objective of the present work is focusing on the basic fluid-mechanics phenomena involved, to show that beneficial effects of tubercles are present even when tubercle details are simplified, in order to couple performance improvement and ease of assembly. Graphical Abstract
- 30 August 2022
- Published by Springer Nature in Experiments in Fluids
- Vol. 63 (9) , 1-18
Open AccessImproving performances of biomimetic wings with leading-edge tubercles
The present study aims investigating experimentally wing/blade geometries in which the leading edge is modified by the presence of artificial bumps, following examples in nature (“biomimetics”). Specifically, the tubercles observed in humpback whales are considered with a special focus on easy manufacturing and performance improvements, trying to overcome the observed lift coefficient reduction before stall in comparison with a standard wing. To this end, different tubercle geometries are tested, by measuring overall forces acting on the wings and by deriving detailed velocity fields using particle image velocimetry. Measurements indicate performance improvements for all trailing edge tubercle geometries here tested. In addition, the detailed analysis of mechanisms underlying the improvement of performances suggests that a triangular shape of the leading edge combines the advantages of easy manufacturing and improvements of pre-stall behaviour. So far, a simple mathematical model, describing tubercles as delta wings, is presented and verified by experimental data. The objective of the present work is focusing on the basic fluid-mechanics phenomena involved, to show that beneficial effects of tubercles are present even when tubercle details are simplified, in order to couple performance improvement and ease of assembly. Graphical Abstract
- Open Access
- 1 August 2021
- Published by Paul V. Galvin Library/Illinois Institute of Technology in 14th International Symposium on Particle Image Velocimetry
- Vol. 1 (1)
Plunging jets from orifices of different geometry
Plunging jets are used in many industrial and civil applications, as for example in sewage and water treatment plants, in order to enhance aeration and mass transfer of volatile gases. They are also observed in natural processes as rivers self-purification, waterfalls and weirs. Many investigations dealt with the plunging jets in different configurations, but the dependence on Reynolds number and jet geometry were still not sufficiently addressed. For example, Mishra et al. (2020) studied an oblique submerged water impinging jet at different nozzle-to-plate distances and impingement angles, but only at a rather small Reynolds numbers (2600). On the other hand, different jet geometries have been extensively considered, but not for the plunging jet configuration (Mi, 2000; Hashiehbaf &Romano, 2013). In this work, plunging water jets issuing in air from orifices of different shape are considered. The aim of the work is to detail and compare jet behaviors in terms of velocity fields generated after impacting the air-water interface, as a function of Reynolds number and orifice geometry. However, air bubbles entrainment is mainly avoided in order to study the jet characteristics in a simpler case and use it as a reference starting point for future works.
- 1 August 2021
- Published by Paul V. Galvin Library/Illinois Institute of Technology in 14th International Symposium on Particle Image Velocimetry
- Vol. 1 (1)
Open AccessPlunging jets from orifices of different geometry
Plunging jets are used in many industrial and civil applications, as for example in sewage and water treatment plants, in order to enhance aeration and mass transfer of volatile gases. They are also observed in natural processes as rivers self-purification, waterfalls and weirs. Many investigations dealt with the plunging jets in different configurations, but the dependence on Reynolds number and jet geometry were still not sufficiently addressed. For example, Mishra et al. (2020) studied an oblique submerged water impinging jet at different nozzle-to-plate distances and impingement angles, but only at a rather small Reynolds numbers (2600). On the other hand, different jet geometries have been extensively considered, but not for the plunging jet configuration (Mi, 2000; Hashiehbaf &Romano, 2013). In this work, plunging water jets issuing in air from orifices of different shape are considered. The aim of the work is to detail and compare jet behaviors in terms of velocity fields generated after impacting the air-water interface, as a function of Reynolds number and orifice geometry. However, air bubbles entrainment is mainly avoided in order to study the jet characteristics in a simpler case and use it as a reference starting point for future works.
- Open Access
- 14 October 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (10) , 933
Performance Evaluation of a Piezoelectric Energy Harvester Based on Flag-Flutter
In the last few decades, piezoelectric (PZT) materials have played a vital role in the aerospace industry because of their energy harvesting capability. PZT energy harvesters (PEH) absorb the energy from an operational environment and can transform it into useful energy to drive nano/micro-electronic components. In this research work, a PEH based on the flag-flutter mechanism is presented. This mechanism is based on fluid-structure interaction (FSI). The flag is subjected to the axial airflow in the subsonic wind tunnel. The performance evaluation of the harvester and aeroelastic analysis is investigated numerically and experimentally. A novel solution is presented to extract energy from Limit Cycle Oscillations (LCOs) phenomenon by means of PZT transduction. The PZT patch absorbs the flow-induced structural vibrations and transforms it into electrical energy. Furthermore, the optimal resistance and length of the flag is predicted to maximize the energy harvesting. Different configurations of flag i.e., with Aluminium (Al) patch and PZT patch for flutter mode vibration mode are studied numerically and experimentally. The bifurcation diagram is constructed for the experimental campaign for the flutter instability of a cantilevered flag in subsonic wind-tunnel. Moreover, the flutter boundary conditions are analysed for reduced critical velocity and frequency. The designed PZT energy harvester via flag-flutter mechanism is suitable for energy harvesting in aerospace engineering applications to drive wireless sensors. The maximum output power that can be generated from the designed harvester is 6.72 mW and the optimal resistance is predicted to be 0.33 M.- 14 October 2020
- Published by MDPI AG in Micromachines
- Vol. 11 (10) , 933
Open AccessPerformance Evaluation of a Piezoelectric Energy Harvester Based on Flag-Flutter
In the last few decades, piezoelectric (PZT) materials have played a vital role in the aerospace industry because of their energy harvesting capability. PZT energy harvesters (PEH) absorb the energy from an operational environment and can transform it into useful energy to drive nano/micro-electronic components. In this research work, a PEH based on the flag-flutter mechanism is presented. This mechanism is based on fluid-structure interaction (FSI). The flag is subjected to the axial airflow in the subsonic wind tunnel. The performance evaluation of the harvester and aeroelastic analysis is investigated numerically and experimentally. A novel solution is presented to extract energy from Limit Cycle Oscillations (LCOs) phenomenon by means of PZT transduction. The PZT patch absorbs the flow-induced structural vibrations and transforms it into electrical energy. Furthermore, the optimal resistance and length of the flag is predicted to maximize the energy harvesting. Different configurations of flag i.e., with Aluminium (Al) patch and PZT patch for flutter mode vibration mode are studied numerically and experimentally. The bifurcation diagram is constructed for the experimental campaign for the flutter instability of a cantilevered flag in subsonic wind-tunnel. Moreover, the flutter boundary conditions are analysed for reduced critical velocity and frequency. The designed PZT energy harvester via flag-flutter mechanism is suitable for energy harvesting in aerospace engineering applications to drive wireless sensors. The maximum output power that can be generated from the designed harvester is 6.72 mW and the optimal resistance is predicted to be 0.33 M. - 1 October 2020
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 118, 110141
Experimental investigation on fluid mechanics of micro-channel heat transfer devices
- 1 October 2020
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 118, 110141
Experimental investigation on fluid mechanics of micro-channel heat transfer devices
- 9 August 2020
- Published by Springer Nature in Experiments in Fluids
- Vol. 61 (9) , 1-18
Propagation of perturbations and meandering in a free surface shallow water jet
- 9 August 2020
- Published by Springer Nature in Experiments in Fluids
- Vol. 61 (9) , 1-18
Propagation of perturbations and meandering in a free surface shallow water jet