Derui Kong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Derui Kong has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Ian Galton
Electrical and Computer Engineering Department, University of California at San Diego, La Jolla, CA, USA
3 shared publications Adesh Garg
Physical Layer Products division, Broadcom Inc., Irvine, CA, USA
1 shared publication- Afshin Momtaz
Broadcom Inc
1 shared publication Ali Nazemi
Physical Layer Products division, Broadcom Inc., Irvine, CA, USA
1 shared publicationAlireza Nilchi
Physical Layer Products division, Broadcom Inc., Irvine, CA, USA
1 shared publicationAminghasem Safarian
Physical Layer Products division, Broadcom Inc., Irvine, CA, USA
1 shared publication
Latest Publications
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 8, 281-284
An 800GbE PAM-4 PHY Transceiver for 42 dB Copper and Direct-Drive Optical Applications in 7 nm
This work presents a low power DSP-based singlechip 800GbE PAM-4 PHY transceiver in 7nm process capable of driving eight lanes of up to 112-Gb/s. It supports both electrical and optical links with monolithic integrated laser driver enabling direct-drive PAM-4 output capability for EML and silicon photonics. The transceiver supports 42dB IL channel at Nyquist with pre-FEC BER<3E-8. The per-lane analog power efficiency is 2.78pJ/b for low-swing drive mode and 4.9pJ/b for direct-drive mode.
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 8, 281-284
An 800GbE PAM-4 PHY Transceiver for 42 dB Copper and Direct-Drive Optical Applications in 7 nm
This work presents a low power DSP-based singlechip 800GbE PAM-4 PHY transceiver in 7nm process capable of driving eight lanes of up to 112-Gb/s. It supports both electrical and optical links with monolithic integrated laser driver enabling direct-drive PAM-4 output capability for EML and silicon photonics. The transceiver supports 42dB IL channel at Nyquist with pre-FEC BER<3E-8. The per-lane analog power efficiency is 2.78pJ/b for low-swing drive mode and 4.9pJ/b for direct-drive mode.
- 27 March 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12169, 25-153
Experimental study on damping of a vibration absorber for a single-piston linear compressor
The vibration of a single-piston linear Stirling Cryocooler caused by the compressor operation seriously affects the component performance and imaging quality of the infrared detector, so in terms of vibration abatement, the use of a vibration absorber has become an important way of vibration damping. While during using the vibration absorber, the damping variation is an important factor affecting the vibration damping performance. Hence, through the experimental analysis of the damping variation of the vibration absorber, it is identified in this paper that the main reason for the damping variation is the variation of mass and amplitude of the vibration absorber, which affects the deformation of the plate spring and the internal friction energy dissipation of the material. It is discovered in the experiment that at the same amplitude, the damping variation is the most stable when the mass of the vibration absorber is 28.6g~36.4g and the amplitude is 1.6~2.1mm. In the end, a vibration-damping experiment is also carried out for the compressor using a vibration absorber with a mass of 33.1g. When the compressor operates at a working frequency of 75Hz and an input power of 6W, its vibration acceleration can be decreased from 42.274m/s2 before vibration damping to 3.047m/s2 .
- 27 March 2022
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12169, 25-153
Experimental study on damping of a vibration absorber for a single-piston linear compressor
The vibration of a single-piston linear Stirling Cryocooler caused by the compressor operation seriously affects the component performance and imaging quality of the infrared detector, so in terms of vibration abatement, the use of a vibration absorber has become an important way of vibration damping. While during using the vibration absorber, the damping variation is an important factor affecting the vibration damping performance. Hence, through the experimental analysis of the damping variation of the vibration absorber, it is identified in this paper that the main reason for the damping variation is the variation of mass and amplitude of the vibration absorber, which affects the deformation of the plate spring and the internal friction energy dissipation of the material. It is discovered in the experiment that at the same amplitude, the damping variation is the most stable when the mass of the vibration absorber is 28.6g~36.4g and the amplitude is 1.6~2.1mm. In the end, a vibration-damping experiment is also carried out for the compressor using a vibration absorber with a mass of 33.1g. When the compressor operates at a working frequency of 75Hz and an input power of 6W, its vibration acceleration can be decreased from 42.274m/s2 before vibration damping to 3.047m/s2 .
- 7 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (9) , 3084-3098
MSE Analysis of a Multi-Loop LMS Pseudo-Random Noise Canceler for Mixed-Signal Circuit Calibration
This paper applies new analytical techniques to evaluate the stability and mean-square error (MSE) convergence of a multi-loop LMS pseudo-random noise canceller which applies to a variety of known mixed-signal circuit calibration techniques. To the authors' knowledge, it is the first published MSE analysis of any multi-loop LMS system, and, unlike most published MSE analyses of single-loop LMS systems, it does not make any simplifying assumptions. The analysis proves that the noise canceler can be made unconditionally stable by design, and provides guidance on how to choose design parameters to achieve a desired level of noise cancellation.
- 7 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 67 (9) , 3084-3098
MSE Analysis of a Multi-Loop LMS Pseudo-Random Noise Canceler for Mixed-Signal Circuit Calibration
This paper applies new analytical techniques to evaluate the stability and mean-square error (MSE) convergence of a multi-loop LMS pseudo-random noise canceller which applies to a variety of known mixed-signal circuit calibration techniques. To the authors' knowledge, it is the first published MSE analysis of any multi-loop LMS system, and, unlike most published MSE analyses of single-loop LMS systems, it does not make any simplifying assumptions. The analysis proves that the noise canceler can be made unconditionally stable by design, and provides guidance on how to choose design parameters to achieve a desired level of noise cancellation.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (8) , 2219-2229
A 600-MS/s DAC With Over 87-dB SFDR and 77-dB Peak SNDR Enabled by Adaptive Cancellation of Static and Dynamic Mismatch Error
This paper presents a Nyquist-rate current-steering digital-to-analog converter that achieves a peak spurious-free dynamic range better than 87 dB and a peak signal-to-noise-and-distortion ratio better than 77 dB over a 265-MHz signal band. It is enabled by a fully integrated digital calibration technique that measures and cancels both static and dynamic mismatch errors over the first Nyquist band, and various circuit-level techniques that mitigate the effects of jitter and inter-symbol interference.
- 1 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (8) , 2219-2229
A 600-MS/s DAC With Over 87-dB SFDR and 77-dB Peak SNDR Enabled by Adaptive Cancellation of Static and Dynamic Mismatch Error
This paper presents a Nyquist-rate current-steering digital-to-analog converter that achieves a peak spurious-free dynamic range better than 87 dB and a peak signal-to-noise-and-distortion ratio better than 77 dB over a 265-MHz signal band. It is enabled by a fully integrated digital calibration technique that measures and cancels both static and dynamic mismatch errors over the first Nyquist band, and various circuit-level techniques that mitigate the effects of jitter and inter-symbol interference.
- 26 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (8) , 2843-2853
Subsampling Mismatch Noise Cancellation for High-Speed Continuous-Time DACs
Clock skew and component mismatches in continuous-time DACs introduce two types of error: static error and dynamic error. Both types of error typically limit the performance of practical, high-resolution, and continuous-time DACs, but most prior calibration techniques primarily reduce only static error. An exception is a recently published mismatch noise cancellation (MNC) technique that adaptively measures and cancels both types of error over the DAC's first Nyquist band. However, a disadvantage of the technique is that it requires an oversampling ADC that operates at several times the DAC's Nyquist rate to prevent convergence error that would otherwise be caused by aliasing. This paper presents a sub-sampling version of the MNC technique that avoids this limitation at the expense of a lower calibration convergence rate. As proven in the paper, the subsampling MNC technique allows aliasing to occur, but in such a way that convergence error is avoided.
- 26 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 66 (8) , 2843-2853
Subsampling Mismatch Noise Cancellation for High-Speed Continuous-Time DACs
Clock skew and component mismatches in continuous-time DACs introduce two types of error: static error and dynamic error. Both types of error typically limit the performance of practical, high-resolution, and continuous-time DACs, but most prior calibration techniques primarily reduce only static error. An exception is a recently published mismatch noise cancellation (MNC) technique that adaptively measures and cancels both types of error over the DAC's first Nyquist band. However, a disadvantage of the technique is that it requires an oversampling ADC that operates at several times the DAC's Nyquist rate to prevent convergence error that would otherwise be caused by aliasing. This paper presents a sub-sampling version of the MNC technique that avoids this limitation at the expense of a lower calibration convergence rate. As proven in the paper, the subsampling MNC technique allows aliasing to occur, but in such a way that convergence error is avoided.
- Open Access
- 25 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 65 (2) , 421-433
Adaptive Cancellation of Static and Dynamic Mismatch Error in Continuous-Time DACs
Inadvertent but inevitable mismatches among nominally identical unit element 1-bit digital-to-analog converters (DACs) within a multi-bit Nyquist-rate DAC cause both static and dynamic error in the DAC's continuous-time output waveform. Prior calibration techniques are able to suppress static mismatch error, but have had limited success in suppressing dynamic mismatch error. This paper presents a digital calibration technique that adaptively measures and cancels both static and dynamic mismatch error over the DAC's first Nyquist band. The technique is capable of either foreground or background operation, and is relatively insensitive to non-ideal circuit behavior. The paper presents a rigorous mathematical analysis of the technique, and demonstrates the results of the paper with both behavioral and transistor-level circuit simulations.
- 25 August 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems I: Regular Papers
- Vol. 65 (2) , 421-433
Open AccessAdaptive Cancellation of Static and Dynamic Mismatch Error in Continuous-Time DACs
Inadvertent but inevitable mismatches among nominally identical unit element 1-bit digital-to-analog converters (DACs) within a multi-bit Nyquist-rate DAC cause both static and dynamic error in the DAC's continuous-time output waveform. Prior calibration techniques are able to suppress static mismatch error, but have had limited success in suppressing dynamic mismatch error. This paper presents a digital calibration technique that adaptively measures and cancels both static and dynamic mismatch error over the DAC's first Nyquist band. The technique is capable of either foreground or background operation, and is relatively insensitive to non-ideal circuit behavior. The paper presents a rigorous mathematical analysis of the technique, and demonstrates the results of the paper with both behavioral and transistor-level circuit simulations.
- 24 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 25 (2) , 774-778
Analysis and Reduction of Nonidealities in Stacked-Transistor Current Sources
An in-depth analysis of nonidealities of CMOS stacked-transistor current sources is presented. This analysis quantifies the impact of series parasitic resistance on the systematic error of stacked-transistor current sources and the effect of partition ratio/partition number on the random mismatch of stacked-transistor current sources. The analytical results are presented in closed-form formulas that enable the explanation of many second-order effects seen from circuit simulation. Various tradeoffs in the design of stacked-transistor current sources are discussed. A weighted sizing technique based on the analytical results is proposed that can optimize the random mismatch of stacked-transistor current sources for a given area budget.
- 24 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 25 (2) , 774-778
Analysis and Reduction of Nonidealities in Stacked-Transistor Current Sources
An in-depth analysis of nonidealities of CMOS stacked-transistor current sources is presented. This analysis quantifies the impact of series parasitic resistance on the systematic error of stacked-transistor current sources and the effect of partition ratio/partition number on the random mismatch of stacked-transistor current sources. The analytical results are presented in closed-form formulas that enable the explanation of many second-order effects seen from circuit simulation. Various tradeoffs in the design of stacked-transistor current sources are discussed. A weighted sizing technique based on the analytical results is proposed that can optimize the random mismatch of stacked-transistor current sources for a given area budget.