Sandor Zoletnik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sandor Zoletnik has a total of 481 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Refy
HUN-REN Centre for Energy Research
16 shared publications - Miklos Vecsei
Centre for Energy Research, Budapest, Hungary
10 shared publications D. Dunai
HUN-REN Centre for Energy Research, 1121 Budapest, Hungary
9 shared publications- Mate Lampert
Princeton Plasma Physics Laboratory
8 shared publications - G. Anda
Wigner Research Centre for Physics, Budapest, Hungary
7 shared publications - Gergo I. Pokol
HUN-REN Centre for Energy Research, Institute for Atomic Energy Research 1 , Budapest
6 shared publications
Latest Publications
- Open Access
- 1 November 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (11)
Feasibility of fast-alpha diagnostics with Pellet Charge Exchange
Characterization of fusion alpha particles is essential for the study of plasmas with significant alpha heating and, consequently, for the scientific success of ITER. Current diagnostic plans include gamma spectroscopy, collective Thomson scattering, charge exchange recombination spectroscopy, and a fast ion loss detector, although it remains unclear whether these methods will fully meet the requirements of this novel experiment. Pellet Charge Exchange (PCX) is an alternative approach in which alpha particles acquire electrons from the neutral cloud of an ablating fueling pellet through charge exchange, producing He+ ions and He atoms. The concept was previously tested in TFTR experiments, where escaping He atoms were analyzed using a neutral particle analyzer. In this work, a new optical approach is explored by modeling the emission of excited He+ ions produced in the charge exchange reactions. This signal could provide information on the density, energy, and distribution of fusion alpha particles along the pellet flight path, in the pedestal region of the plasma. The presented results are based on solving a system of rate equations for the n-resolved ionization states of alpha particles propagating through pellet clouds, with cloud parameters obtained from the Hydrogen Pellet Injection code HPI2. The model tracks the populations of ionization and excitation states of helium in one dimension, including the density of He+ (n = 4) states whose emission would be observed. Estimates of emission intensity and signal-to-background ratio based on expected bremsstrahlung radiation are also provided, identifying viable parameter ranges for PCX diagnostics.
- 1 November 2026
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 97 (11)
Open AccessFeasibility of fast-alpha diagnostics with Pellet Charge Exchange
Characterization of fusion alpha particles is essential for the study of plasmas with significant alpha heating and, consequently, for the scientific success of ITER. Current diagnostic plans include gamma spectroscopy, collective Thomson scattering, charge exchange recombination spectroscopy, and a fast ion loss detector, although it remains unclear whether these methods will fully meet the requirements of this novel experiment. Pellet Charge Exchange (PCX) is an alternative approach in which alpha particles acquire electrons from the neutral cloud of an ablating fueling pellet through charge exchange, producing He+ ions and He atoms. The concept was previously tested in TFTR experiments, where escaping He atoms were analyzed using a neutral particle analyzer. In this work, a new optical approach is explored by modeling the emission of excited He+ ions produced in the charge exchange reactions. This signal could provide information on the density, energy, and distribution of fusion alpha particles along the pellet flight path, in the pedestal region of the plasma. The presented results are based on solving a system of rate equations for the n-resolved ionization states of alpha particles propagating through pellet clouds, with cloud parameters obtained from the Hydrogen Pellet Injection code HPI2. The model tracks the populations of ionization and excitation states of helium in one dimension, including the density of He+ (n = 4) states whose emission would be observed. Estimates of emission intensity and signal-to-background ratio based on expected bremsstrahlung radiation are also provided, identifying viable parameter ranges for PCX diagnostics.
- Open Access
- 10 September 2026
- Published by Elsevier in SSRN Electronic Journal
Desublimation model for cryogenic pellet production
In fusion devices, cryogenic technologies have a crucial role, not only in superconducting magnet cooling but also in the formation of cryogenic pellets that are used for disruption mitigation, control and fuelling of the plasma of fusion reactors. These pellets are key elements in the reliability and safe operation of a fusion reactor. At the HUN-REN Centre for Energy Research, a support laboratory has been set up to study cryogenic pellet production, launch and shattering of large protium, deuterium, neon, and neon-hydrogen mixture pellets for the ITER Disruption Mitigation System (DMS).,The development of this technology requires a better understanding of how these cryogenic pellets form. We intend to model the desublimation of H2, D2, Ne, and Ar pellets on a cold wall to determine the strategy for pellet preparation. We intend to use this model for a 1D simulation and validate it experimentally for H2 desublimation at sub-millibar pressure. In this paper, the formulation and validation of this methodology are introduced. The results of this paper take us one step closer to an operational fusion reactor.
- 10 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDesublimation model for cryogenic pellet production
In fusion devices, cryogenic technologies have a crucial role, not only in superconducting magnet cooling but also in the formation of cryogenic pellets that are used for disruption mitigation, control and fuelling of the plasma of fusion reactors. These pellets are key elements in the reliability and safe operation of a fusion reactor. At the HUN-REN Centre for Energy Research, a support laboratory has been set up to study cryogenic pellet production, launch and shattering of large protium, deuterium, neon, and neon-hydrogen mixture pellets for the ITER Disruption Mitigation System (DMS).,The development of this technology requires a better understanding of how these cryogenic pellets form. We intend to model the desublimation of H2, D2, Ne, and Ar pellets on a cold wall to determine the strategy for pellet preparation. We intend to use this model for a 1D simulation and validate it experimentally for H2 desublimation at sub-millibar pressure. In this paper, the formulation and validation of this methodology are introduced. The results of this paper take us one step closer to an operational fusion reactor.
- Open Access
- 20 May 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 229
Gas flow and dust in Shattered Pellet Injection
- 20 May 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 229
Open AccessGas flow and dust in Shattered Pellet Injection
- Open Access
- 24 March 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 227
Comparison of propellant gas suppressor configurations for Shattered Pellet Injector
- 24 March 2026
- Published by Elsevier in Fusion Engineering and Design
- Vol. 227
Open AccessComparison of propellant gas suppressor configurations for Shattered Pellet Injector
- 24 July 2025
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 82 (3) , 636-658
Atomic Beam Probe Synthetic Diagnostic in the COMPASS Tokamak and Its Application in Fusion Plasmas
- 24 July 2025
- Published by Taylor & Francis in Fusion Science and Technology
- Vol. 82 (3) , 636-658
Atomic Beam Probe Synthetic Diagnostic in the COMPASS Tokamak and Its Application in Fusion Plasmas
- Open Access
- 24 December 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (1) , 015022
Operation of a lithium beam diagnostic in tritium and deuterium–tritium experiments at JET
A fast neutral lithium beam has been used at JET for more than 30 years to measure profiles of electron density in the pedestal and scrape off layer. The diagnostic was not designed for tritium operation. In this paper, we describe the modifications which were required to allow operation in tritium (T) and deuterium–tritium (D-T) fuelled pulses at JET in 2021 and 2023. Methods to allow remote startup and remote control of the beam were implemented. The vacuum pump and exhaust system had to be made tritium compatible. Radiation vulnerable electronics had to be removed from the torus hall. The observation system relied on regular in vessel mirror exchange. An in-vessel protection shield was installed close to the observation mirror to protect the mirror surface. Operation in T and D-T discharges, maintenance post tritium exposure, commissioning and the calibration of the diagnostic are discussed.
- 24 December 2024
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 67 (1) , 015022
Open AccessOperation of a lithium beam diagnostic in tritium and deuterium–tritium experiments at JET
A fast neutral lithium beam has been used at JET for more than 30 years to measure profiles of electron density in the pedestal and scrape off layer. The diagnostic was not designed for tritium operation. In this paper, we describe the modifications which were required to allow operation in tritium (T) and deuterium–tritium (D-T) fuelled pulses at JET in 2021 and 2023. Methods to allow remote startup and remote control of the beam were implemented. The vacuum pump and exhaust system had to be made tritium compatible. Radiation vulnerable electronics had to be removed from the torus hall. The observation system relied on regular in vessel mirror exchange. An in-vessel protection shield was installed close to the observation mirror to protect the mirror surface. Operation in T and D-T discharges, maintenance post tritium exposure, commissioning and the calibration of the diagnostic are discussed.
- 6 September 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 208
Analysis of pellet propellant gas expansion in the test bench of the ITER DMS Support Laboratory
- 6 September 2024
- Published by Elsevier in Fusion Engineering and Design
- Vol. 208
Analysis of pellet propellant gas expansion in the test bench of the ITER DMS Support Laboratory
- 1 September 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (9)
Applicability of alkali beam emission spectroscopy on NSTX-U
Understanding fast pedestal dynamics and turbulent transport in the edge and scrape-off layer (SOL) plasma of spherical tokamaks is crucial for the design and operation of future fusion reactors. The alkali beam emission spectroscopy diagnostic technique offers a means to measure the absolute electron density radial profile and fluctuation amplitude in these regions. In this study, we demonstrate that injecting a sodium neutral beam radially into the plasma and analyzing the light emission from its 3p–3s atomic transition using near-orthogonal viewing angles allows for accurate measurement of the electron density profile and fluctuations in the National Spherical Torus Experiment (NSTX) Upgrade spherical tokamak. Our findings indicate a peak signal-to-noise ratio of 118 in the pedestal and 12 in the SOL under typical NSTX plasma conditions. The spatial resolution for the electron density profile is estimated to be between 2 and 8 mm, while for fluctuation measurements, it ranges from 12 to 15 mm.
- 1 September 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (9)
Applicability of alkali beam emission spectroscopy on NSTX-U
Understanding fast pedestal dynamics and turbulent transport in the edge and scrape-off layer (SOL) plasma of spherical tokamaks is crucial for the design and operation of future fusion reactors. The alkali beam emission spectroscopy diagnostic technique offers a means to measure the absolute electron density radial profile and fluctuation amplitude in these regions. In this study, we demonstrate that injecting a sodium neutral beam radially into the plasma and analyzing the light emission from its 3p–3s atomic transition using near-orthogonal viewing angles allows for accurate measurement of the electron density profile and fluctuations in the National Spherical Torus Experiment (NSTX) Upgrade spherical tokamak. Our findings indicate a peak signal-to-noise ratio of 118 in the pedestal and 12 in the SOL under typical NSTX plasma conditions. The spatial resolution for the electron density profile is estimated to be between 2 and 8 mm, while for fluctuation measurements, it ranges from 12 to 15 mm.
- Open Access
- 7 August 2024
- Published by IOP Publishing in Nuclear Fusion
- Vol. 64 (9) , 096033
Production and launch studies of cryogenic pellets for the ITER disruption mitigation system
A support laboratory has been set up to study pellet production, launch and shattering of cryogenic protium, deuterium, and neon pellets for the ITER disruption mitigation system, which plans to use 28.5 × 57 mm (diameter × length) protium, neon an mixture pellets in the Shattered Pellet Injectors. Such large protium pellets have not been produced and launched before, therefore the desublimation and launch process have been studied in detail in two steps. First 19 mm diameter pellets were produced, followed by the demonstration of the final pellet size. Pellet desublimation recipes were established for all pellet types, and it was found that, under certain conditions, even the large neon pellets can be launched with a propellant gas pulse, without requiring a mechanical punch device. This is attributed to cryogenic snow formation on the surface of the pellet. Conditions for the snow formation are studied and tendencies are understood using simple calculations.
- 7 August 2024
- Published by IOP Publishing in Nuclear Fusion
- Vol. 64 (9) , 096033
Open AccessProduction and launch studies of cryogenic pellets for the ITER disruption mitigation system
A support laboratory has been set up to study pellet production, launch and shattering of cryogenic protium, deuterium, and neon pellets for the ITER disruption mitigation system, which plans to use 28.5 × 57 mm (diameter × length) protium, neon an mixture pellets in the Shattered Pellet Injectors. Such large protium pellets have not been produced and launched before, therefore the desublimation and launch process have been studied in detail in two steps. First 19 mm diameter pellets were produced, followed by the demonstration of the final pellet size. Pellet desublimation recipes were established for all pellet types, and it was found that, under certain conditions, even the large neon pellets can be launched with a propellant gas pulse, without requiring a mechanical punch device. This is attributed to cryogenic snow formation on the surface of the pellet. Conditions for the snow formation are studied and tendencies are understood using simple calculations.
- Open Access
- 1 July 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (7)
Charge exchange recombination spectroscopy on the alkali beam of Wendelstein 7-X
Measurements of ion temperature profiles are required to assess the energy and particle transport processes in the Wendelstein 7-X stellarator. This device is equipped with a diagnostic alkali beam, which can be utilized to determine local impurity temperatures and densities by Charge Exchange Recombination Spectroscopy (CXRS). It could provide such profiles in the edge plasma, where other diagnostics are less efficient. With this contribution, first results of CXRS measurements on the sodium beam from the scientific operation phase OP2.1 are presented. The spectroscopic system was in commissioning phase lacking some of the final optical components. Thus, the aim of the diagnostics during this campaign was to explore the measurement capabilities. Based on the processed spectra, the prospects of C5+ and C6+ ion temperature and concentration measurements are discussed. The results indicate that with the final optical setup under installation, the diagnostics could provide ion temperature profiles in the edge with 3 mm radial resolution and at least 1 s temporal resolution.
- 1 July 2024
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 95 (7)
Open AccessCharge exchange recombination spectroscopy on the alkali beam of Wendelstein 7-X
Measurements of ion temperature profiles are required to assess the energy and particle transport processes in the Wendelstein 7-X stellarator. This device is equipped with a diagnostic alkali beam, which can be utilized to determine local impurity temperatures and densities by Charge Exchange Recombination Spectroscopy (CXRS). It could provide such profiles in the edge plasma, where other diagnostics are less efficient. With this contribution, first results of CXRS measurements on the sodium beam from the scientific operation phase OP2.1 are presented. The spectroscopic system was in commissioning phase lacking some of the final optical components. Thus, the aim of the diagnostics during this campaign was to explore the measurement capabilities. Based on the processed spectra, the prospects of C5+ and C6+ ion temperature and concentration measurements are discussed. The results indicate that with the final optical setup under installation, the diagnostics could provide ion temperature profiles in the edge with 3 mm radial resolution and at least 1 s temporal resolution.