Mohannad Theeb Al-Jarrah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mohannad Theeb Al-Jarrah has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Al-Harahsheh
Jordan University of Science and Technology
3 shared publications - Ala’a Mhmoued Abdllh Alboull
State Key Laboratory of Electroanalytical Chemistry, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, 5625 Renmin Street, Changchun, Jilin 130022, P. R. China
1 shared publication - Amith Khandakar
Qatar University
1 shared publication - Azad Ashraf
Chemical Engineering Department, University of Doha for Science and Technology, Doha, Qatar
1 shared publication - Bayan Abdul Majeed Al-Malak
Civil Engineering, Jordan University of Science and Technology, Irbid, Jordan
1 shared publication - Borhan Aldeen Albiss
Institute of Nanotechnology, Jordan University of Science and Technology, Irbid 22110, Jordan
1 shared publication
Latest Publications
- Open Access
Enhancing the Photocatalytic Activity of TiO2 Nanoparticles with Cyclodextrin-Functionalized Graphene and Noble Metals for Organic Pollutant Degradation
Contamination of water resources by organic pollutants is a major environmental issue. Utilizing photocatalytic materials for the degradation of these pollutants presents a viable strategy for environmental clean-up. This study introduces the synthesis of an organic/inorganic hybrid photocatalyst of β-cyclodextrin (β-CD)/reduced graphene oxide (rGO) and titanium oxide (TiO2) nanoparticles. The nanocomposite was characterized by using FT-IR, XRD, SEM, and EDAX, and the photocatalytic activity was studied by measuring the photodegradation of methylene blue (MB) under simulated solar radiation. The synthesized nanocomposite showed excellent stability and performance, with up to 92% photodegradation of MB. To further enhance the photocatalytic activity, the synthesized nanocomposite underwent modification with Ag and Pt nanoparticles. Within 90 min, photodegradation rates of 100% and 97% for MB were attained with Pt and Ag nanoparticles that were loaded at 5 wt.%, respectively. The photocatalyst’s reusability was evaluated through multiple usage cycles. Additionally, the impact of functionalization on the band gap alteration of TiO2 is reported.
Open AccessEnhancing the Photocatalytic Activity of TiO2 Nanoparticles with Cyclodextrin-Functionalized Graphene and Noble Metals for Organic Pollutant Degradation
Contamination of water resources by organic pollutants is a major environmental issue. Utilizing photocatalytic materials for the degradation of these pollutants presents a viable strategy for environmental clean-up. This study introduces the synthesis of an organic/inorganic hybrid photocatalyst of β-cyclodextrin (β-CD)/reduced graphene oxide (rGO) and titanium oxide (TiO2) nanoparticles. The nanocomposite was characterized by using FT-IR, XRD, SEM, and EDAX, and the photocatalytic activity was studied by measuring the photodegradation of methylene blue (MB) under simulated solar radiation. The synthesized nanocomposite showed excellent stability and performance, with up to 92% photodegradation of MB. To further enhance the photocatalytic activity, the synthesized nanocomposite underwent modification with Ag and Pt nanoparticles. Within 90 min, photodegradation rates of 100% and 97% for MB were attained with Pt and Ag nanoparticles that were loaded at 5 wt.%, respectively. The photocatalyst’s reusability was evaluated through multiple usage cycles. Additionally, the impact of functionalization on the band gap alteration of TiO2 is reported.
- Open Access
Parametric Study of Gold Nanoparticles Synthesis under Micro-Continuous Flow Conditions
The synthesis of gold nanoparticles (GNPs) using chemical reduction in batch and microreactor methods has been reported. A parametric study of the effect of several parameters on the size of gold nanoparticles was performed in batch synthesis mode using the modified Martin method. The best-obtained conditions were used to synthesize gold nanoparticles using a glass chip microreactor, and the size of the resulting GNPs from both methods was compared. The presence of polyvinyl alcohol (SC) was used as a capping agent, and sodium borohydride (SB) was used as a reducing agent. Several parameters were studied, including HAuCl4, SC, SB concentrations, the volumetric ratio of SB to gold precursor, pH, temperature, and mixing speed. Various techniques were used to characterize the resulting nanoparticles, including Atomic Absorbance spectroscopy (AAS), Ultraviolet-visible spectroscopy (UV-Vis), and dynamic light scratching (DLS). Optimum conditions were obtained for the synthesis of gold nanoparticles. Under similar reaction conditions, the microreactor consistently produced smaller nanoparticles in the range of 10.42–11.31 nm with a reaction time of less than 1 min.
Open AccessParametric Study of Gold Nanoparticles Synthesis under Micro-Continuous Flow Conditions
The synthesis of gold nanoparticles (GNPs) using chemical reduction in batch and microreactor methods has been reported. A parametric study of the effect of several parameters on the size of gold nanoparticles was performed in batch synthesis mode using the modified Martin method. The best-obtained conditions were used to synthesize gold nanoparticles using a glass chip microreactor, and the size of the resulting GNPs from both methods was compared. The presence of polyvinyl alcohol (SC) was used as a capping agent, and sodium borohydride (SB) was used as a reducing agent. Several parameters were studied, including HAuCl4, SC, SB concentrations, the volumetric ratio of SB to gold precursor, pH, temperature, and mixing speed. Various techniques were used to characterize the resulting nanoparticles, including Atomic Absorbance spectroscopy (AAS), Ultraviolet-visible spectroscopy (UV-Vis), and dynamic light scratching (DLS). Optimum conditions were obtained for the synthesis of gold nanoparticles. Under similar reaction conditions, the microreactor consistently produced smaller nanoparticles in the range of 10.42–11.31 nm with a reaction time of less than 1 min.
- Open Access
Preparation and Characterization of Polymer Membranes Impregnated with Carbon Nanotubes for Olive Mill Wastewater
In this study, polymer membrane(s) impregnated with carbon nanotubes (CNTs) were developed, characterized and evaluated for removing phenolic compounds from olive mill wastewater; thus, protecting the environment and public health. Polyethersulfone/functionalized, multi-walled carbon nanotube (PES/fCNTs) membranes were synthesized via the phase inversion method using PES and acid-treated CNTs. The prepared membranes were then characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and contact angle. Results obtained from this study indicate a more hydrophilic surface for the prepared PES/fCNTs membranes, with a higher pure water flux compared to the polyethersulfone (PES) membranes. In addition, the amount of fCNTs in the membranes was found to be the most significant factor affecting the morphology and water flux of the membranes. The PES/fCNTs membranes at 1 bar with 0 wt.% and 1 wt.% of CNTs showed water flux of 37.8 and 69.71 kg/h.m2, respectively. In addition, PES/fCNTs membranes with 0.5 wt.% fCNTs showed the highest total phenol content removal of 74%.
Open AccessPreparation and Characterization of Polymer Membranes Impregnated with Carbon Nanotubes for Olive Mill Wastewater
In this study, polymer membrane(s) impregnated with carbon nanotubes (CNTs) were developed, characterized and evaluated for removing phenolic compounds from olive mill wastewater; thus, protecting the environment and public health. Polyethersulfone/functionalized, multi-walled carbon nanotube (PES/fCNTs) membranes were synthesized via the phase inversion method using PES and acid-treated CNTs. The prepared membranes were then characterized by scanning electron microscopy (SEM), Fourier-transform infrared spectroscopy (FTIR) and contact angle. Results obtained from this study indicate a more hydrophilic surface for the prepared PES/fCNTs membranes, with a higher pure water flux compared to the polyethersulfone (PES) membranes. In addition, the amount of fCNTs in the membranes was found to be the most significant factor affecting the morphology and water flux of the membranes. The PES/fCNTs membranes at 1 bar with 0 wt.% and 1 wt.% of CNTs showed water flux of 37.8 and 69.71 kg/h.m2, respectively. In addition, PES/fCNTs membranes with 0.5 wt.% fCNTs showed the highest total phenol content removal of 74%.
- 21 May 2021
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 15 (2) , 284-302
Assessing the Use of Alumina Microfibers as Modifiers to Enhance the Physical and Rheological Properties of Asphalt Binders
- 21 May 2021
- Published by Springer Nature in International Journal of Pavement Research and Technology
- Vol. 15 (2) , 284-302
Assessing the Use of Alumina Microfibers as Modifiers to Enhance the Physical and Rheological Properties of Asphalt Binders
- 1 October 2020
- Published by Elsevier in Journal of Environmental Management
- Vol. 271, 110970
Concentrative isolation of uranium traces in aqueous solutions via resurfaced-magnetic carbon nanotube suspension
- 1 October 2020
- Published by Elsevier in Journal of Environmental Management
- Vol. 271, 110970
Concentrative isolation of uranium traces in aqueous solutions via resurfaced-magnetic carbon nanotube suspension
- 1 October 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (5) , 5662-5669
In situ synthesis of quaternary ammonium on silica-coated magnetic nanoparticles and it’s application for the removal of uranium (VI) from aqueous media
- 1 October 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (5) , 5662-5669
In situ synthesis of quaternary ammonium on silica-coated magnetic nanoparticles and it’s application for the removal of uranium (VI) from aqueous media