Michele Norgia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Michele Norgia has a total of 77 co-authors. Here are the top co-authors by number of shared publications:
- Federico Cavedo
Department of Electronics, Information and Bioengineering, Politecnico di Milano, 20133 Milan, Italy
13 shared publications - Parisa Esmaili
Department of Electronics, Information and Bioengineering, Politecnico di Milano, I-20133 Milan, Italy
13 shared publications - Alessandro Pesatori
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milano, Italy
12 shared publications - Silvano Donati
University of Pavia
8 shared publications C. Svelto
Dipartimento di Elettronica e Informazione - Politecnico di Milano, Piazza Leonardo Da Vinci, 32 - 20133 Milano - Italy. Phone: +39 02 2399.3601, Fax: +39 02 2399.3412
4 shared publicationsAlessandro Pesatori
Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Via Ponzio 34/5, 20133 Milano, Italy
3 shared publications
Latest Publications
- Open Access
- 27 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 163 (1) , 18
Frequency Modulation Self-Mixing Interferometer: Architecture and Performances
This work describes the architecture of a self-mixing interferometer measured in frequency modulation, with particular emphasis on how to realize the setup and the electronics required for the various functions. The architecture can be useful for improving the performance for different optoelectronic sensor applications, in terms of bandwidth, sensitivity and NED. Many of the measurement applications of self-mixing interferometry can be replaced with frequency readout, gaining two orders of magnitude in sensitivity.
- 27 October 2026
- Published by MDPI AG in Engineering Proceedings
- Vol. 163 (1) , 18
Open AccessFrequency Modulation Self-Mixing Interferometer: Architecture and Performances
This work describes the architecture of a self-mixing interferometer measured in frequency modulation, with particular emphasis on how to realize the setup and the electronics required for the various functions. The architecture can be useful for improving the performance for different optoelectronic sensor applications, in terms of bandwidth, sensitivity and NED. Many of the measurement applications of self-mixing interferometry can be replaced with frequency readout, gaining two orders of magnitude in sensitivity.
- Open Access
Closing Editorial: Editorial Board Members’ Collection Series: Optical Measurements and Sensing Technology
This editorial provides closing remarks for the Special Issue on “Optical Measurements and Sensing Technology” published in Sensors
Open AccessClosing Editorial: Editorial Board Members’ Collection Series: Optical Measurements and Sensing Technology
This editorial provides closing remarks for the Special Issue on “Optical Measurements and Sensing Technology” published in Sensors
- Open Access
Closing Editorial: Advancements in Optical Measurement Devices and Technologies
Optical measurement technologies have emerged as indispensable tools in modern metrology, offering precision, noninvasive measurement capabilities, and remarkable versatility across diverse scientific and industrial applications
Open AccessClosing Editorial: Advancements in Optical Measurement Devices and Technologies
Optical measurement technologies have emerged as indispensable tools in modern metrology, offering precision, noninvasive measurement capabilities, and remarkable versatility across diverse scientific and industrial applications
- Open Access
- 1 February 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3179 (1)
Benchmarking of a Cost-effective Micro-Interferometer for Remote Vibration Monitoring
A low-cost and low-size interferometer, based on self-mixing interferometry, has been developed for replacing standard accelerometers. The structure of the micro-interferometer is described in detail, and its measurement performances are evaluated with particular reference to preventive diagnosis of mechanical systems. For this purpose, a test bench equipped with accelerometers was used, on which intact or damaged ball bearings can be mounted. In the experimental tests carried out, the micro-interferometer showed signiAicantly superior performance to accelerometers in reporting faulty behaviour of the mechanical structure.
- 1 February 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3179 (1)
Open AccessBenchmarking of a Cost-effective Micro-Interferometer for Remote Vibration Monitoring
A low-cost and low-size interferometer, based on self-mixing interferometry, has been developed for replacing standard accelerometers. The structure of the micro-interferometer is described in detail, and its measurement performances are evaluated with particular reference to preventive diagnosis of mechanical systems. For this purpose, a test bench equipped with accelerometers was used, on which intact or damaged ball bearings can be mounted. In the experimental tests carried out, the micro-interferometer showed signiAicantly superior performance to accelerometers in reporting faulty behaviour of the mechanical structure.
- Open Access
- 1 February 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3179 (1)
FM Self-mixing Interferometer Measurement Performance
Self-mixing interferometry achieves remarkable performance thanks to the frequency modulation reading. In this case the noise floor is no longer due to shot noise, as for amplitude modulation, but to the laser’s frequency noise. This work experimentally compares the noise floor of this particular kind of interferometer for different laser types, DFB and VCSEL, which exhibit different line broadenings. Experimental measurement of the FM noise spectrum confirms the theoretical treatment that it is determined by the laser’s linewidth. In the particular case of a VCSEL laser, the 1/f noise in frequency modulation clearly indicate a gaussian broadening of the laser linewidth.
- 1 February 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3179 (1)
Open AccessFM Self-mixing Interferometer Measurement Performance
Self-mixing interferometry achieves remarkable performance thanks to the frequency modulation reading. In this case the noise floor is no longer due to shot noise, as for amplitude modulation, but to the laser’s frequency noise. This work experimentally compares the noise floor of this particular kind of interferometer for different laser types, DFB and VCSEL, which exhibit different line broadenings. Experimental measurement of the FM noise spectrum confirms the theoretical treatment that it is determined by the laser’s linewidth. In the particular case of a VCSEL laser, the 1/f noise in frequency modulation clearly indicate a gaussian broadening of the laser linewidth.
- Open Access
- 24 October 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 193
Measurement of linewidth and noise dependence on the optical feedback parameter C by means of an FM-Converted Self-Mix interferometer
- 24 October 2025
- Published by Elsevier in Optics & Laser Technology
- Vol. 193
Open AccessMeasurement of linewidth and noise dependence on the optical feedback parameter C by means of an FM-Converted Self-Mix interferometer
- Open Access
Performance Measurement of an Electromagnetic Guided-Wave Liquid Level Sensor
Slight changes in the local properties of a transmission line, dipped in a liquid, can be used to estimate its level through two different determination techniques, involving the capacitance and electromagnetic wave speed, measured by the time of flight. Indeed, the overall capacitance of a transmission line varies linearly with the liquid level, as well as the time of flight of the electromagnetic wave. Both quantities can be estimated via the measurement of a phase shift at radio frequencies, and the simultaneous measurements can be realized using a compact and low-cost design working at a few megahertz. This paper presents a further improvement in sensitivity to challenge the performance of this kind of level sensor, dealing with liquids with low dielectric constants. To better describe this effect, a study on the overall capacitance of different transmission path segments was conducted in COMSOL Multiphysics. The level measurement was performed experimentally on the realized prototype while considering the measured phase shift as a function of the liquid level, for both an unshielded twisted-pair and magnet wires. As the results showed, with the magnet wires the sensitivity was improved by a factor of about 4, consistently aligning with the simulation results and providing a predictable phase shift response with increasing liquid levels. Consequently, magnet wire is a good choice for precise level measurements through RF phase shifts, especially in the case of low relative permittivity liquids.
Open AccessPerformance Measurement of an Electromagnetic Guided-Wave Liquid Level Sensor
Slight changes in the local properties of a transmission line, dipped in a liquid, can be used to estimate its level through two different determination techniques, involving the capacitance and electromagnetic wave speed, measured by the time of flight. Indeed, the overall capacitance of a transmission line varies linearly with the liquid level, as well as the time of flight of the electromagnetic wave. Both quantities can be estimated via the measurement of a phase shift at radio frequencies, and the simultaneous measurements can be realized using a compact and low-cost design working at a few megahertz. This paper presents a further improvement in sensitivity to challenge the performance of this kind of level sensor, dealing with liquids with low dielectric constants. To better describe this effect, a study on the overall capacitance of different transmission path segments was conducted in COMSOL Multiphysics. The level measurement was performed experimentally on the realized prototype while considering the measured phase shift as a function of the liquid level, for both an unshielded twisted-pair and magnet wires. As the results showed, with the magnet wires the sensitivity was improved by a factor of about 4, consistently aligning with the simulation results and providing a predictable phase shift response with increasing liquid levels. Consequently, magnet wire is a good choice for precise level measurements through RF phase shifts, especially in the case of low relative permittivity liquids.
- 5 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Active Protection System for Safety Stop Mechanism in Portable Cutting Tools
Achieving a comprehensive protection system associated with unpredictability of human behavior, complexity of the cutting task and variety of the environmental working condition, is a task which presents a considerable challenge. To address such difficulties, this paper presents an effective detection algorithm based on the measurement of impedance between the bar of chainsaw and the rear handle, extended by the human body. A multitone signal has been exploited to evaluate the system's response and validate the equivalent electrical model experimentally. To evaluate the transfer function, discrete Fourier Transform is performed, and the Fourier coefficients are evaluated by multiplying the acquired signals by two vectors of sine and cosine at four frequencies. As results show, the magnitude of the transfer function carries information about the approaching distance while phase provides very useful information to distinguish between the proximity to body instead of tree. Finally, the developed algorithm demonstrates a successful human body detection rate of 100% with 4% of false-positive detections.
- 5 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Active Protection System for Safety Stop Mechanism in Portable Cutting Tools
Achieving a comprehensive protection system associated with unpredictability of human behavior, complexity of the cutting task and variety of the environmental working condition, is a task which presents a considerable challenge. To address such difficulties, this paper presents an effective detection algorithm based on the measurement of impedance between the bar of chainsaw and the rear handle, extended by the human body. A multitone signal has been exploited to evaluate the system's response and validate the equivalent electrical model experimentally. To evaluate the transfer function, discrete Fourier Transform is performed, and the Fourier coefficients are evaluated by multiplying the acquired signals by two vectors of sine and cosine at four frequencies. As results show, the magnitude of the transfer function carries information about the approaching distance while phase provides very useful information to distinguish between the proximity to body instead of tree. Finally, the developed algorithm demonstrates a successful human body detection rate of 100% with 4% of false-positive detections.
- Open Access
Multi-Sensor Laser System for Electric Guitar Pitch-Detection
To attain a direct MIDI output from an electric guitar, we devised and implemented a sophisticated laser sensor system capable of measuring finger positions. This sensor operates on the principle of optical triangulation, employing six lasers and seven position-sensing detectors that are time-multiplexed. The speed and precision of this sensor system meet the necessary criteria for creating an electric guitar with a direct digital output, perfectly satisfying the application’s requirements.
Open AccessMulti-Sensor Laser System for Electric Guitar Pitch-Detection
To attain a direct MIDI output from an electric guitar, we devised and implemented a sophisticated laser sensor system capable of measuring finger positions. This sensor operates on the principle of optical triangulation, employing six lasers and seven position-sensing detectors that are time-multiplexed. The speed and precision of this sensor system meet the necessary criteria for creating an electric guitar with a direct digital output, perfectly satisfying the application’s requirements.
- Open Access
Study of the Errors in Interpolated Fast Fourier Transform for Interferometric Applications
Frequency estimation is often the basis of various measurement techniques, among which optical distance measurement stands out. One of the most used techniques is interpolated fast Fourier transform due to its simplicity, combined with good performance. In this work, we study the limits of this technique in the case of real signals, with reference to a particular interferometric technique known as self-mixing interferometry. The aim of this research is the better understanding of frequency estimation performances in real applications, together with guidance on how to improve them in specific optical measurement techniques. An optical rangefinder, based on self-mixing interferometry, has been realized and characterized. The simulation results allow us to explain the limits of the interpolated fast Fourier transform applied to the realized instrument. Finally, a method for overcoming them is proposed by decorrelating the errors between the measurements, which can provide a guideline for the design of frequency-modulated interferometric distance meters.
Open AccessStudy of the Errors in Interpolated Fast Fourier Transform for Interferometric Applications
Frequency estimation is often the basis of various measurement techniques, among which optical distance measurement stands out. One of the most used techniques is interpolated fast Fourier transform due to its simplicity, combined with good performance. In this work, we study the limits of this technique in the case of real signals, with reference to a particular interferometric technique known as self-mixing interferometry. The aim of this research is the better understanding of frequency estimation performances in real applications, together with guidance on how to improve them in specific optical measurement techniques. An optical rangefinder, based on self-mixing interferometry, has been realized and characterized. The simulation results allow us to explain the limits of the interpolated fast Fourier transform applied to the realized instrument. Finally, a method for overcoming them is proposed by decorrelating the errors between the measurements, which can provide a guideline for the design of frequency-modulated interferometric distance meters.