Pracha Osklang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Pracha Osklang has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Chuwong Phongcharoenpanich
School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand
2 shared publications Akkarat Boonpoonga
1 shared publication- Arnon Sakonkanapong
Faculty of Engineering
1 shared publication - Bancha Luadang
Faculty of Engineering, Rajamangala University of Technology Rattanakosin,Department of Instrumentation Engineering,Nakhon Pathom,Thailand
1 shared publication Chuwong Phongcharoenpanich
1 shared publication- Kittima Lertsakwimarn
Faculty of Industrial Technology and Management, King Mongkut's University of Technology North Bangkok,Department of Industrial Management,Bangkok,Thailand
1 shared publication
Latest Publications
- Open Access
- 1 January 2023
- Published by Tech Science Press in Computers, Materials & Continua
- Vol. 74 (1) , 503-522
Artificial Magnetic Conductor as Planar Antenna for 5G Evolution
A 5G wireless system requests a high-performance compact antenna device. This research work aims to report the characterization and verification of the artificial magnetic conductor (AMC) metamaterial for a high-gain planar antenna. The configuration is formed by a double-side structure on an intrinsic dielectric slab. The 2-D periodic pattern as an impedance surface is mounted on the top surface, whereas at the bottom surface the ground plane with an inductive narrow aperture source is embedded. The characteristic of the resonant transmission is illustrated based on the electromagnetic virtual object of the AMC resonant structure to reveal the unique property of a magnetic material response. The characteristics of the AMC metamaterial and the planar antenna synthesis are investigated and verified by experiment using a low-cost FR4 dielectric material. The directional antenna gain is obviously enhanced by guiding a primary field radiation. The loss effect in a dielectric slab is essentially studied having an influence on antenna radiation. The verification shows a peak of the antenna gain around 9.7 dB at broadside which is improved by 6.2 dB in comparison with the primary aperture antenna without the AMC structure. The thin antenna profile of λ/37.5 is achieved at 10 GHz for 5G evolution. The emission property in an AMC structure herein contributes to the development of a low-profile and high-gain planar antenna for a compact wireless component.
- 1 January 2023
- Published by Tech Science Press in Computers, Materials & Continua
- Vol. 74 (1) , 503-522
Open AccessArtificial Magnetic Conductor as Planar Antenna for 5G Evolution
A 5G wireless system requests a high-performance compact antenna device. This research work aims to report the characterization and verification of the artificial magnetic conductor (AMC) metamaterial for a high-gain planar antenna. The configuration is formed by a double-side structure on an intrinsic dielectric slab. The 2-D periodic pattern as an impedance surface is mounted on the top surface, whereas at the bottom surface the ground plane with an inductive narrow aperture source is embedded. The characteristic of the resonant transmission is illustrated based on the electromagnetic virtual object of the AMC resonant structure to reveal the unique property of a magnetic material response. The characteristics of the AMC metamaterial and the planar antenna synthesis are investigated and verified by experiment using a low-cost FR4 dielectric material. The directional antenna gain is obviously enhanced by guiding a primary field radiation. The loss effect in a dielectric slab is essentially studied having an influence on antenna radiation. The verification shows a peak of the antenna gain around 9.7 dB at broadside which is improved by 6.2 dB in comparison with the primary aperture antenna without the AMC structure. The thin antenna profile of λ/37.5 is achieved at 10 GHz for 5G evolution. The emission property in an AMC structure herein contributes to the development of a low-profile and high-gain planar antenna for a compact wireless component.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 133, 1-3
Wideband UHF Reflector Antenna for DVB Applications
This paper presents the design, measurement, and development of a bow tie wideband antenna using scutcheon shape with inductive-loaded for DVB applications. The antenna consists of 3 elements; a scutcheon bow tie radiator, a line inductive-loaded and a square reflector. The element of bow tie achieves a lower frequency of 470 MHz. The element of line inductive-loaded achieves an upper frequency of 860 MHz for |S11| of less than −10 dB. The measured results of the prototype antenna are good agreement. The impedance bandwidth of 81.27%, which covering a frequency range from 374 MHz to 886 MHz. The measured gains are flat around 7 dBi over the DVB band. The HPBW in the vertical and horizontal planes are 56.8° and 117.3° at frequency of 660 MHz.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 133, 1-3
Wideband UHF Reflector Antenna for DVB Applications
This paper presents the design, measurement, and development of a bow tie wideband antenna using scutcheon shape with inductive-loaded for DVB applications. The antenna consists of 3 elements; a scutcheon bow tie radiator, a line inductive-loaded and a square reflector. The element of bow tie achieves a lower frequency of 470 MHz. The element of line inductive-loaded achieves an upper frequency of 860 MHz for |S11| of less than −10 dB. The measured results of the prototype antenna are good agreement. The impedance bandwidth of 81.27%, which covering a frequency range from 374 MHz to 886 MHz. The measured gains are flat around 7 dBi over the DVB band. The HPBW in the vertical and horizontal planes are 56.8° and 117.3° at frequency of 660 MHz.
- Open Access
- 28 August 2019
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2019, 1-13
Triband Compact Printed Antenna for 2.4/3.5/5 GHz WLAN/WiMAX Applications
This research presents a triband compact printed antenna for WLAN and WiMAX applications. The antenna structure consists of a folded open stub, long and short L-shaped strips, and asymmetric trapezoid ground plane. Besides, it is of simple structure and operable in 2.4 GHz and 5 GHz (5.2/5.8 GHz) WLAN and 3.5/5.5 GHz WiMAX bands. The folded open stub and long and short L-shaped strips realize impedance matching at 2.4, 3.5, 5.2, and 5.8 GHz, and the asymmetric trapezoid ground plane fine-tunes impedance matching at 5.2, 5.5, and 5.8 GHz. In addition, the equivalent circuit model consolidated into lumped elements is also presented to explain its impedance matching characteristics. In this study, simulations were carried out, and a prototype antenna was fabricated and experimented. The simulation and experimental results are in good agreement. Specifically, the simulated and experimental radiation patterns are omnidirectional at 2.4, 3.5, and 5.2 GHz and near-omnidirectional at 5.5 and 5.8 GHz. Furthermore, the simulated and measured antenna gains are 1.269–3.074 dBi and 1.10–2.80 dBi, respectively. Essentially, the triband compact printed antenna covers 2.4 GHz and 5 GHz (5.2/5.8 GHz) WLAN and 3.5/5.5 GHz WiMAX frequency bands and thereby is a good candidate for WLAN/WiMAX applications.
- 28 August 2019
- Published by Wiley in International Journal of Antennas and Propagation
- Vol. 2019, 1-13
Open AccessTriband Compact Printed Antenna for 2.4/3.5/5 GHz WLAN/WiMAX Applications
This research presents a triband compact printed antenna for WLAN and WiMAX applications. The antenna structure consists of a folded open stub, long and short L-shaped strips, and asymmetric trapezoid ground plane. Besides, it is of simple structure and operable in 2.4 GHz and 5 GHz (5.2/5.8 GHz) WLAN and 3.5/5.5 GHz WiMAX bands. The folded open stub and long and short L-shaped strips realize impedance matching at 2.4, 3.5, 5.2, and 5.8 GHz, and the asymmetric trapezoid ground plane fine-tunes impedance matching at 5.2, 5.5, and 5.8 GHz. In addition, the equivalent circuit model consolidated into lumped elements is also presented to explain its impedance matching characteristics. In this study, simulations were carried out, and a prototype antenna was fabricated and experimented. The simulation and experimental results are in good agreement. Specifically, the simulated and experimental radiation patterns are omnidirectional at 2.4, 3.5, and 5.2 GHz and near-omnidirectional at 5.5 and 5.8 GHz. Furthermore, the simulated and measured antenna gains are 1.269–3.074 dBi and 1.10–2.80 dBi, respectively. Essentially, the triband compact printed antenna covers 2.4 GHz and 5 GHz (5.2/5.8 GHz) WLAN and 3.5/5.5 GHz WiMAX frequency bands and thereby is a good candidate for WLAN/WiMAX applications.