Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Vinod Belwanshi has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Finite Element Analysis of MEMS Pressure Sensors Intended for Subsonic Wind Tunnel Applications

    by Rahul Kumar Singh, Vinod Belwanshi, Neela Chattoraj, Richa Mishra

  • IoT-enabled peristaltic micropump platform for microneedle mediated drug delivery and body fluid sampling: simulation and feasibility

    by Sachin Kr. Singh, Atul Arya, Baishnavi Prasad, Preksha Baid, Priyank Saxena, Vinod Belwanshi, Richa Mishra

  • Open Access

    Sputtered Piezoelectric AlN Thin Films: Parameter Optimisation, Deposition Challenges, and Emerging Perspectives—A Review

    by Rangaraajan Muralidaran, Paritosh Dubey, Kuldeep Singh Gour, Shuvam Pawar, Vinod Belwanshi, Jacopo Iannacci

    This article reviews the reactive magnetron sputtering of piezoelectric Aluminium Nitride (AlN) thin films, with a focus on process parameter optimisation and system-level deposition challenges. AlN is a leading material for MEMS and RF applications owing to its c-axis (002) orientation, high acoustic velocity, wide bandgap (∼6.2 eV), and CMOS compatibility. We review the influence of sputtering power, nitrogen flow ratio, substrate temperature, and target-to-substrate distance on crystallographic quality and document practical hardware challenges, including vacuum leakage, grounding faults, target erosion, and mass flow controller drift, that critically affect reproducibility but are systematically underreported in the literature. A perspective is provided on emerging application domains where optimised AlN films address current performance gaps, including next-generation RF/telecom systems towards 6G and Future Networks, harsh environment sensing and actuation, biomedical ultrasound, and IoT energy harvesting. The complementarity between AlN and Silicon Carbide (SiC) is discussed for high-temperature, high-power, and radiation-hard MEMS, where AlN/SiC heterostructures combine the piezoelectric activity of AlN with the mechanical and chemical robustness of SiC. It also incorporates a discussion of dopant- and heteroepitaxy-based AlN engineering, AlN deposition on a wider range of substrates, the role of seed and electrode underlayers, and pulsed-DC sputtering as a third power supply mode alongside RF and conventional DC.

  • Experimental Demonstration of a DC Excited Coreless Planar PCB Coil Actuator Targeted for Lateral Microactuation in MEMS

    by Praful P. Kabadi, Abhijit D. Kamble, Vinod Belwanshi, Sanjay E. Talole, Bhubon Ch. Mech

    Electromagnetic micro actuators in microelectromechanical systems (MEMS) applications have an advantage for large displacement and quick actuation. However, most of the micro-actuator designs require permanent magnets or ferromagnetic cores to concentrate magnetic flux, which leads to complicated integration. To the best of our knowledge, this work presents the first experimental proof-of-concept demonstration of a coreless planar printed circuit board (PCB) coil actuator, which is capable of achieving lateral displacement of a ferromagnetic dipole made of nickel sheet using only magnetic field gradients generated by the coil, without any permanent magnets or ferromagnetic cores. This work is also significant as the concept is highly suitable for implementation in MEMS micro actuators fabricated using metal UV LIGA process. The work presents a 15-turn planar spiral coil fabricated on flame-retardant 4 (FR4) substrate using optimized ultraviolet (UV) lithography, showing a case of lateral micro-actuation. The work also focuses on optimizing the process to achieve track widths of ∼80 μm after resolving challenges of lateral etching and resolution limitations. Experimental testing with a Nickel dipole of dimensions approximately 13.5 × 1.5 × 0.02 mm with ∼12 mg weight demonstrated smooth and repeatable lateral displacement of ∼0.75 mm at 0.425 A DC drive current, closely matching the behavior that was predicted based on the magnetic profile that were obtained by simulations. The theoretical force analysis predicts magnetic forces of 1163.6 μN, which significantly exceeds the gravitational force (∼117.67 μN) and kinetic friction forces (41.185 μN), with experimental validation confirming consistent displacement performance across multiple trials. Compared with piezoelectric and electrostatic MEMS actuators, which achieve micrometer-scale motion, the proposed device demonstrates two orders of magnitude higher displacement.

  • Enhancing pressure sensor performance through diaphragm geometry optimization for subsonic applications

    by Rahul Kumar Singh, Pallavi Patel, Neela Chattoraj, Vinod Belwanshi, Richa Mishra


  • Degradation Mechanism of Piezoresistive Sensors Under the Influence of γ -Ray Irradiation

    by Vinod Belwanshi, Khushwant Sehra, Aryan, Ayushi Dixit, Poonam Kasturi, Manoj Saxena

    Micro-Electro-Mechanical Systems (MEMS) technology based piezoresistive technique is a highly matured transduction technique. It is very popular for the MEMS devices used in various industries like automotive, process control, aerospace & avionics, consumer electronics, nuclear power plants, and many more. MEMS pressure sensors are one among them, and their deployment in nuclear power plant and aerospace are prominently increasing. Hence radiation-induced performance degradation of piezoresistive pressure sensors has been carried out, which is a prime concern for such industries. Therefore, a set of experiments for the investigation of irradiation driven performance degradation of MEMS pressure sensors are performed under varying doses of gamma radiations. An insignificant change in sensitivity was recorded which degraded up to a maximum of 0.78 %, while the linearity remained unchanged for a cumulative dose of 27.90 Mrad. However, the deviation in the offset voltage of the Wheatstone bridge configuration was significant and as recorded was 139% at a cumulative dose of 27.90 Mrad. This manuscript explains the degradation mechanism of MEMS piezoresistive sensors using the experiments and TCAD simulations.


  • Open Access

    Design Guidelines for Thin Diaphragm-Based Microsystems through Comprehensive Numerical and Analytical Studies

    by Vinod Belwanshi, Kedarnath Rane, Vibhor Kumar, Bidhan Pramanick

    This paper presents comprehensive guidelines for the design and analysis of a thin diaphragm that is used in a variety of microsystems, including microphones and pressure sensors. It highlights the empirical relations that can be utilized for the design of thin diaphragm-based microsystems (TDMS). Design guidelines developed through a Finite Element Analysis (FEA) limit the iterative efforts to fabricate TDMS. These design guidelines are validated analytically, with the assumption that the material properties are isotropic, and the deviation from anisotropic material is calculated. In the FEA simulations, a large deflection theory is taken into account to incorporate nonlinearity, such that a critical dimensional ratio of a/h or 2r/h can be decided to have the linear response of a thin diaphragm. The observed differences of 12% in the deflection and 13% in the induced stresses from the analytical calculations are attributed to the anisotropic material consideration in the FEA model. It suggests that, up to a critical ratio (a/h or 2r/h), the thin diaphragm shows a linear relationship with a high sensitivity. The study also presents a few empirical relations to finalize the geometrical parameters of the thin diaphragm in terms of its edge length or radius and thickness. Utilizing the critical ratio calculated in the static FEA analysis, the basic conventional geometries are considered for harmonic analyses to understand the frequency response of the thin diaphragms, which is a primary sensing element for microphone applications and many more. This work provides a solution to microelectromechanical system (MEMS) developers for reducing cost and time while conceptualizing TDMS designs.


  • Open Access

    Investigation of temperature sensitivity of a MEMS gravimeter based on geometric anti-spring

    by Vinod Belwanshi, Abhinav Prasad, Karl Toland, Richard Middlemiss, Douglas Paul, Giles Hammond

    This paper describes a technique for temperature sensitivity or thermal sag measurements of a geometric anti-spring based microelectromechanical system (MEMS) gravimeter (Wee-g). The Wee-g MEMS gravimeter is currently fabricated on a (100) silicon wafer using standard micro-nano fabrication techniques. The thermal behavior of silicon indicates that the Young’s modulus of silicon decreases with increase in temperature (∼64 ppm/K). This leads to a softening of the silicon material, resulting in the proof mass displacing (or sagging) under the influence of increasing temperature. It results in a change in the measured gravity, which is expressed as temperature sensitivity in terms of change in gravity per degree temperature. The temperature sensitivity for the silicon based MEMS gravimeter is found to be 60.14–64.87, 61.76, and 62.76 µGal/mK for experimental, finite element analysis (FEA) simulation, and analytical calculations, respectively. It suggests that the gravimeter's temperature sensitivity is dependent on the material properties used to fabricate the MEMS devices. In this paper, the experimental measurements of thermal sag are presented along with analytical calculations and simulations of the effect using FEA. The bespoke optical measurement system to quantify the thermal sag is also described. The results presented are an essential step toward the development of temperature insensitive MEMS gravimeters.


  • Open Access

    Invetigation of Temperature Sensitivity of a Geomteric Anti-Spring based MEMS Gravimeter

    by Vinod Belwanshi, Abhinav Prasad, Karl Toland, Richard Middlemiss, Douglas Paul, Giles Hammond

    This paper describes a temperature sensitivity or thermal sag measurement of a geometric anti-spring based micro-electromechanical system (MEMS) gravimeter (Wee-g). The Wee-g MEMS gravimeter is currently fabricated on a (100) silicon wafer using standard micro-nano fabrication techniques. The thermal behavior of silicon indicates that the Young's modulus of silicon decreases with an increase in temperature (around 63 ppm/K). This leads to a softening of the silicon material resulting in the proof mass (PM) displacing (or sagging) under the influence of an increasing temperature. It results in the change on the measured gravity and it is expressed as a temperature sensitivity in terms of change in gravity per degree temperature. The temperature sensitivity for the silicon based MEMS gravimeter is found to be 60.14-64.87 muGal/mK, 61.76 muGal/mK and 62.76 muGal/mK for experimental, finite element analysis (FEA) simulation and analytical calculations respectively. It suggests that temperature sensitivity is depended on material properties used to fabricate the MEMS devices. In this paper the experimental measurements of thermal sag are presented, along with analytical calculations and simulations of the effect using FEA (finite element analysis). The bespoke optical measurement system to quantify the thermal sag is also described. The results presented are an essential step towards the development of temperature insensitive MEMS gravimeters.