Yilmaz Sozer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Yilmaz Sozer has a total of 133 co-authors. Here are the top co-authors by number of shared publications:
- Iqbal Husain
Electrical and Computer Engineering, North Carolina State University, Raleigh, NC, USA
17 shared publications Ali Elrayyah
Qatar Environment and Energy Research Institute, Doha, Qatar
10 shared publications- Shuvajit Das
Electrical and Computer Engineering Department, University of Akron, Akron, OH, USA
10 shared publications - Ehsanul Haque
Electrical and Computer Engineering, University of Akron, Akron, OH, USA
8 shared publications - Ali Elrayyah
Qatar Environment and Energy Research Institute, Doha, Qatar
6 shared publications - Anik Chowdhury
Department of Electrical and Computer Engineering, The University of Akron, Akron, OH, USA
6 shared publications
Latest Publications
- 13 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 4234-4245
Comparative Performance Analysis of Slotted and Slotless Dual-Stator and Single-Rotor Axial-Flux Permanent Magnet Motor for Integrated Motor-Compressor System
Axial-flux permanent magnet (AFPM) machines are well suited for a wide range of applications. Their compatibility and potential for integrated motor-compressor systems are explored in this paper. Three-phase dual-stator and single-rotor AFPM motors with Slotted and Slotless stator topologies with two different slot/pole configurations are studied in this paper. 18-slot/12-pole and 27-slot/24-pole configurations with 10 kW rated power and 12,000 rpm rated speed are compared for different performance aspects. The enclosure of the motor is held constant with several other parameters to obtain a fair comparison. Cost analysis is performed to address the cost-effectiveness of the AFPM machines. A prototype is constructed of a 27-slot/24-pole configuration of a Slotless AFPM motor for experimental validation.
- 13 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 4234-4245
Comparative Performance Analysis of Slotted and Slotless Dual-Stator and Single-Rotor Axial-Flux Permanent Magnet Motor for Integrated Motor-Compressor System
Axial-flux permanent magnet (AFPM) machines are well suited for a wide range of applications. Their compatibility and potential for integrated motor-compressor systems are explored in this paper. Three-phase dual-stator and single-rotor AFPM motors with Slotted and Slotless stator topologies with two different slot/pole configurations are studied in this paper. 18-slot/12-pole and 27-slot/24-pole configurations with 10 kW rated power and 12,000 rpm rated speed are compared for different performance aspects. The enclosure of the motor is held constant with several other parameters to obtain a fair comparison. Cost analysis is performed to address the cost-effectiveness of the AFPM machines. A prototype is constructed of a 27-slot/24-pole configuration of a Slotless AFPM motor for experimental validation.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 3753-3763
A Modified Geometry-Based Analytical Model of Switched Reluctance Motor for Rapid Design Process
This paper presents a Modified Geometry-Based Analytical Model for Switched Reluctance Machines (SRM) to facilitate a rapid design process. The primary objectives involve enhancing the accuracy of flux linkage and torque predictions by introducing modifications to the conventional geometry-based analytical model. The proposed model accounts for the tapering of stator and rotor poles, providing a more realistic representation of SRM pole shapes. The analytical model also considers the basic geometric parameters like turns, phase current, and geometric dimensions that affect average torque and current density. Methodologically, the research employs analytical derivations based on the modified geometry, utilizing equations that consider the impact of fringing flux and saturation effects on iron. The Flux Linkage Models are used to calculate Co-energy and static torque as functions of rotor position. These models are crucial for understanding and predicting the energy characteristics and mechanical output of SRMs at different rotor positions. The model's validity is compared with Finite Element Analysis (FEA) and experimental results from an 18-slot 12 pole (18/12) SRM prototype. The study also conducts a comparative analysis with the conventional analytical model, demonstrating the improved accuracy achieved through the proposed modifications.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 61 (3) , 3753-3763
A Modified Geometry-Based Analytical Model of Switched Reluctance Motor for Rapid Design Process
This paper presents a Modified Geometry-Based Analytical Model for Switched Reluctance Machines (SRM) to facilitate a rapid design process. The primary objectives involve enhancing the accuracy of flux linkage and torque predictions by introducing modifications to the conventional geometry-based analytical model. The proposed model accounts for the tapering of stator and rotor poles, providing a more realistic representation of SRM pole shapes. The analytical model also considers the basic geometric parameters like turns, phase current, and geometric dimensions that affect average torque and current density. Methodologically, the research employs analytical derivations based on the modified geometry, utilizing equations that consider the impact of fringing flux and saturation effects on iron. The Flux Linkage Models are used to calculate Co-energy and static torque as functions of rotor position. These models are crucial for understanding and predicting the energy characteristics and mechanical output of SRMs at different rotor positions. The model's validity is compared with Finite Element Analysis (FEA) and experimental results from an 18-slot 12 pole (18/12) SRM prototype. The study also conducts a comparative analysis with the conventional analytical model, demonstrating the improved accuracy achieved through the proposed modifications.
- 23 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1762-1773
Dynamic Interleaving Strategy to Reduce DC-Link Ripple of Dual Three-Phase Permanent Magnet Synchronous Machine Drives by Using Discontinuous Space Vector Modulation
A dynamic interleaving method is proposed in this article to reduce the dc-link ripple for dual three-phase permanent synchronous machine drive systems. Existing literature covers the constant interleaving approach, where the interleaving angle is fixed, which is incapable of reducing the dc-link ripple significantly. During the overlapping condition of the dc-link currents of the two three-phase subsystems, the proposed method uses an interleaving angle of π while the rest of the time it is 0. As the proposed method is dynamically varying the interleaving angle, it is called the dynamic interleaving approach. All the dominant harmonics in the dc-link ripple are reduced through the proposed strategy, whereas the constant interleaving cannot reduce all the harmonics. The performance of the proposed strategy is compared to constant interleaving and noninterleaving approaches. Through the proposed method, the dc-link ripple is significantly reduced compared to other approaches, and thus, it improves the power density of the system. Simulation and experimental results are provided to validate the performance of the proposed strategy.
- 23 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 1762-1773
Dynamic Interleaving Strategy to Reduce DC-Link Ripple of Dual Three-Phase Permanent Magnet Synchronous Machine Drives by Using Discontinuous Space Vector Modulation
A dynamic interleaving method is proposed in this article to reduce the dc-link ripple for dual three-phase permanent synchronous machine drive systems. Existing literature covers the constant interleaving approach, where the interleaving angle is fixed, which is incapable of reducing the dc-link ripple significantly. During the overlapping condition of the dc-link currents of the two three-phase subsystems, the proposed method uses an interleaving angle of π while the rest of the time it is 0. As the proposed method is dynamically varying the interleaving angle, it is called the dynamic interleaving approach. All the dominant harmonics in the dc-link ripple are reduced through the proposed strategy, whereas the constant interleaving cannot reduce all the harmonics. The performance of the proposed strategy is compared to constant interleaving and noninterleaving approaches. Through the proposed method, the dc-link ripple is significantly reduced compared to other approaches, and thus, it improves the power density of the system. Simulation and experimental results are provided to validate the performance of the proposed strategy.
- 16 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (6) , 8627-8641
Investigation of Effective Cases of Radial Force Sum Flattening for Acoustic Noise Reduction in Four Three-Phase Switched Reluctance Motors With Different Pole Configuration
This paper presents an investigation of the effective and less effective cases of a method called ‘radial force sum flattening’, for the vibration and acoustic noise reduction in three-phase switched reluctance motors (SRMs) with different pole configuration. Example of four three-phase SRMs, such as 24/16, 18/12, 12/8, and 6/10 SRMs are presented. The principle of the radial force sum flattening is described, along with the limitation of the method. The verification of the radial force sum flattening is carried out by Finite Element Analysis and experimental results in the SRMs. The analysis results show that the vibration and acoustic noise in SRM are affected by the pole configuration. In SRMs with high pole number, such as 24/16, 18/12, and 12/8 SRMs, the significant vibration and acoustic noise are caused by zeroth mode force excitation. While the notable vibration and acoustic noise in 6/10 SRM are caused by second mode force excitation. The radial force sum flattening is effective in reducing the acoustic noise caused by zeroth mode force excitation.
- 16 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (6) , 8627-8641
Investigation of Effective Cases of Radial Force Sum Flattening for Acoustic Noise Reduction in Four Three-Phase Switched Reluctance Motors With Different Pole Configuration
This paper presents an investigation of the effective and less effective cases of a method called ‘radial force sum flattening’, for the vibration and acoustic noise reduction in three-phase switched reluctance motors (SRMs) with different pole configuration. Example of four three-phase SRMs, such as 24/16, 18/12, 12/8, and 6/10 SRMs are presented. The principle of the radial force sum flattening is described, along with the limitation of the method. The verification of the radial force sum flattening is carried out by Finite Element Analysis and experimental results in the SRMs. The analysis results show that the vibration and acoustic noise in SRM are affected by the pole configuration. In SRMs with high pole number, such as 24/16, 18/12, and 12/8 SRMs, the significant vibration and acoustic noise are caused by zeroth mode force excitation. While the notable vibration and acoustic noise in 6/10 SRM are caused by second mode force excitation. The radial force sum flattening is effective in reducing the acoustic noise caused by zeroth mode force excitation.
- 9 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (5) , 6835-6845
Design Optimization of Bifilar Wound Switched Reluctance Motor Drives
The bifilar wound switched reluctance motor (BSRM) has transformer-like windings on the stator known as primary and secondary windings and has a unique power converter known asthe bifilar converter. In this study, an optimized BSRM winding topology along with the lossless snubber for the converter is proposed. The topology investigates the uneven number of turns on the primary and secondary windings of the BSRM while taking into account the converter switch voltage spike, secondary winding current density, and demagnetization time. A lossless snubber circuit is introduced to suppress the switch voltage spike caused by the leakage inductance while preserving the efficiency of the bifilar converter. Another motivation for this research is that the bifilar converter uses fewer switches and diodes than the asymmetric half-bridge converter, which is promising to reduce costs and improve drive system efficiency. The BSRM drive system is designed and compared with the same size conventionally wound switched reluctance motor (CSRM) drive system in terms of physical structure, and efficiency using a multi-physics circuit and finite element analysis (FEA) simulation tools. The operating principle of the bifilar converter has been thoroughly examined, further, the physical setup of the BSRM drive system is tested, and the experimental results are provided
- 9 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (5) , 6835-6845
Design Optimization of Bifilar Wound Switched Reluctance Motor Drives
The bifilar wound switched reluctance motor (BSRM) has transformer-like windings on the stator known as primary and secondary windings and has a unique power converter known asthe bifilar converter. In this study, an optimized BSRM winding topology along with the lossless snubber for the converter is proposed. The topology investigates the uneven number of turns on the primary and secondary windings of the BSRM while taking into account the converter switch voltage spike, secondary winding current density, and demagnetization time. A lossless snubber circuit is introduced to suppress the switch voltage spike caused by the leakage inductance while preserving the efficiency of the bifilar converter. Another motivation for this research is that the bifilar converter uses fewer switches and diodes than the asymmetric half-bridge converter, which is promising to reduce costs and improve drive system efficiency. The BSRM drive system is designed and compared with the same size conventionally wound switched reluctance motor (CSRM) drive system in terms of physical structure, and efficiency using a multi-physics circuit and finite element analysis (FEA) simulation tools. The operating principle of the bifilar converter has been thoroughly examined, further, the physical setup of the BSRM drive system is tested, and the experimental results are provided
- 24 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (4) , 6103-6112
Design, Optimization, and Development of an Axial Flux Interior Permanent Magnet Motor with a Novel Flux Barrier
An axial flux permanent magnet (AFPM) motor can be considered one of the optimal motor designs due to its higher torque density and compact sizing. The majority of the AFPM models to date adopted surface mounted and spoke type rotor designs for various applications. However, these designs provide poor protection for the magnets. On the other hand, magnets in an AFPM can be placed inside well-designed flux barriers to guard against harsh conditions. This paper describes the design, optimization and prototype development of a double stator single rotor (DSSR) axial flux interior permanent magnet (AFIPM) motor with a novel “H” shaped flux barrier. At first, a preliminary design of the AFIPM with the flux barrier has been developed based on requirements and design equations. A multi-stage optimization method including Taguchi orthogonal array, multivariate regression analysis and the genetic algorithm has been used to calculate the optimal design parameters of the motor. Detailed electromagnetic finite element simulations have been carried out to compare the performance of the optimized model with the baseline design. Finally, a prototype of AFPIM has been developed and experimental results have been verified with simulation data.
- 24 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (4) , 6103-6112
Design, Optimization, and Development of an Axial Flux Interior Permanent Magnet Motor with a Novel Flux Barrier
An axial flux permanent magnet (AFPM) motor can be considered one of the optimal motor designs due to its higher torque density and compact sizing. The majority of the AFPM models to date adopted surface mounted and spoke type rotor designs for various applications. However, these designs provide poor protection for the magnets. On the other hand, magnets in an AFPM can be placed inside well-designed flux barriers to guard against harsh conditions. This paper describes the design, optimization and prototype development of a double stator single rotor (DSSR) axial flux interior permanent magnet (AFIPM) motor with a novel “H” shaped flux barrier. At first, a preliminary design of the AFIPM with the flux barrier has been developed based on requirements and design equations. A multi-stage optimization method including Taguchi orthogonal array, multivariate regression analysis and the genetic algorithm has been used to calculate the optimal design parameters of the motor. Detailed electromagnetic finite element simulations have been carried out to compare the performance of the optimized model with the baseline design. Finally, a prototype of AFPIM has been developed and experimental results have been verified with simulation data.
- 17 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 8019-8029
NVH Performance Improvement in Switched Reluctance Machines by Simultaneous Radial Force and Torque Ripple Minimizations
This paper introduces a novel optimum current profile generation technique based on the simultaneous reduction of torque ripple and radial force ripple for acoustic noise and vibration reduction in Switched Reluctance Machines (SRMs). Optimum current profiles at various operating points are generated through electromagnetic finite element analysis (FEA) aided dynamic simulations. Multi-physics simulations are performed to evaluate the NVH performance of the SRM drive for both conventional and proposed current waveforms, which show significant comparative improvements for the proposed methodology. A prototype SRM rated at 100 kW power with a maximum operating speed of 4250 rpm is constructed for testing. The proposed method is tested against the conventional current profiling technique at numerous operating points, encompassing a wide operation speed range. Test results are cross matched against simulation results, which validates the accuracy of the implemented modeling process. Moreover, test results show significant improvement in NVH performance and validate the effectiveness of the proposed methodology. A peak improvement of 19.93 dBA is seen from experimental results for the proposed current profiling technique at 800 rpm 200 Nm output torque condition.
- 17 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Transportation Electrification
- Vol. 10 (4) , 8019-8029
NVH Performance Improvement in Switched Reluctance Machines by Simultaneous Radial Force and Torque Ripple Minimizations
This paper introduces a novel optimum current profile generation technique based on the simultaneous reduction of torque ripple and radial force ripple for acoustic noise and vibration reduction in Switched Reluctance Machines (SRMs). Optimum current profiles at various operating points are generated through electromagnetic finite element analysis (FEA) aided dynamic simulations. Multi-physics simulations are performed to evaluate the NVH performance of the SRM drive for both conventional and proposed current waveforms, which show significant comparative improvements for the proposed methodology. A prototype SRM rated at 100 kW power with a maximum operating speed of 4250 rpm is constructed for testing. The proposed method is tested against the conventional current profiling technique at numerous operating points, encompassing a wide operation speed range. Test results are cross matched against simulation results, which validates the accuracy of the implemented modeling process. Moreover, test results show significant improvement in NVH performance and validate the effectiveness of the proposed methodology. A peak improvement of 19.93 dBA is seen from experimental results for the proposed current profiling technique at 800 rpm 200 Nm output torque condition.
- 16 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3524-3536
Fleet Speed Profile Optimization for Autonomous and Connected Vehicles
A fuel cost optimization method for a fleet of autonomous electric vehicles is proposed using the total cost of the fleet to generate the optimum speed profile. The proposed method also assures maintaining a safe distance from the adjacent vehicles and safe lane changing on multilane roads. While the method aims to get the optimum fleet speed, the individual speed of each vehicle is adjusted based on the relative distance from the leading vehicle. A deep neural network ( DNN ) based autonomous electric vehicle modeling considering all the route conditions is provided. Extensive simulations and experimental studies were performed to develop vehicle models and individual signatures to include in the process. The optimization is performed for a fleet of multiple vehicle types where the physical models of the vehicles vary quite a bit. The proposed optimization algorithm was implemented for different case studies, and it shows a consistent reduction of the total fuel cost for the fleet compared to the optimization done based on only the leading vehicle's cost and a significant improvement compared to unoptimized fleet operation.
- 16 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 60 (2) , 3524-3536
Fleet Speed Profile Optimization for Autonomous and Connected Vehicles
A fuel cost optimization method for a fleet of autonomous electric vehicles is proposed using the total cost of the fleet to generate the optimum speed profile. The proposed method also assures maintaining a safe distance from the adjacent vehicles and safe lane changing on multilane roads. While the method aims to get the optimum fleet speed, the individual speed of each vehicle is adjusted based on the relative distance from the leading vehicle. A deep neural network ( DNN ) based autonomous electric vehicle modeling considering all the route conditions is provided. Extensive simulations and experimental studies were performed to develop vehicle models and individual signatures to include in the process. The optimization is performed for a fleet of multiple vehicle types where the physical models of the vehicles vary quite a bit. The proposed optimization algorithm was implemented for different case studies, and it shows a consistent reduction of the total fuel cost for the fleet compared to the optimization done based on only the leading vehicle's cost and a significant improvement compared to unoptimized fleet operation.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 16245-16255
A Three-Phase Overlapping Winding–Based Wireless Charging System for Transportation Applications
This article proposes a two-layer overlapping winding–based three-phase wireless vehicle charging system with a coil span of 180°. This coil structure offers higher coupling and balance inductance matrices between the transmitter and receiver and improves system efficiency. The system performance improvement has been validated through detailed analysis and simulation results and compared with the benchmark for the same electrical parameters, air gap, and coil volume. Finite element analysis–based simulation results were presented for a 7.7-kW wireless power transfer (WPT) over a 200-mm air gap. An experimental prototype of the proposed system is developed operating at the resonant frequency of 86 kHz with a 200-mm air gap between the coils to validate the design. Both the simulation and experimental results showed a significant increase in efficiency and coupling compared to the conventional WPT systems.
- 28 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 38 (12) , 16245-16255
A Three-Phase Overlapping Winding–Based Wireless Charging System for Transportation Applications
This article proposes a two-layer overlapping winding–based three-phase wireless vehicle charging system with a coil span of 180°. This coil structure offers higher coupling and balance inductance matrices between the transmitter and receiver and improves system efficiency. The system performance improvement has been validated through detailed analysis and simulation results and compared with the benchmark for the same electrical parameters, air gap, and coil volume. Finite element analysis–based simulation results were presented for a 7.7-kW wireless power transfer (WPT) over a 200-mm air gap. An experimental prototype of the proposed system is developed operating at the resonant frequency of 86 kHz with a 200-mm air gap between the coils to validate the design. Both the simulation and experimental results showed a significant increase in efficiency and coupling compared to the conventional WPT systems.
- 17 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (6) , 7620-7633
A Complete Small-Signal Modelling and Adaptive Stability Analysis of Nonlinear Droop-Controlled Microgrids
Nonlinear droop control has been introduced to establish an effective power-sharing between distributed generators without the need for communication links in microgrids (MGs). However, one of the missing studies in the literature is the effects of nonlinear droop relations on the stability of the MGs. In this paper, the stability of an inverter-based MG operating with the nonlinear frequency droop-control has been analyzed. A complete small-signal state-space linearized model of the MG system, with optimized nonlinear droop relations, has been developed considering the dynamics of the overall system and is updated periodically. The stability of the system is then checked online at different operating points. Small-signal stability analysis of an islanded microgrid was performed using MATLAB/Simulink and the results were experimentally verified on an MG setup.
- 17 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (6) , 7620-7633
A Complete Small-Signal Modelling and Adaptive Stability Analysis of Nonlinear Droop-Controlled Microgrids
Nonlinear droop control has been introduced to establish an effective power-sharing between distributed generators without the need for communication links in microgrids (MGs). However, one of the missing studies in the literature is the effects of nonlinear droop relations on the stability of the MGs. In this paper, the stability of an inverter-based MG operating with the nonlinear frequency droop-control has been analyzed. A complete small-signal state-space linearized model of the MG system, with optimized nonlinear droop relations, has been developed considering the dynamics of the overall system and is updated periodically. The stability of the system is then checked online at different operating points. Small-signal stability analysis of an islanded microgrid was performed using MATLAB/Simulink and the results were experimentally verified on an MG setup.