Saha Dauji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Saha Dauji has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Kapilesh Bhargava
Homi Bhabha National Institute
8 shared publicationsP. K. Srivastava
Nuclear Recycle Board, Bhabha Atomic Research Centre
5 shared publications- Tirumalesh Keesari
Isotope and Radiation Application Division, Bhabha Atomic Research Centre, Mumbai, India
5 shared publications - Soubhagya Karmakar
Doctoral Candidate, Structural Safety, Risk & Reliability (SSRR) Lab, Dept. of Civil Engineering, Indian Institute of Technology Bombay, Mumbai, Maharasthra 400094, India; Scientific Officer, Dept. of Atomic Energy, Mumbai, Maharasthra 400094, India. ORCID
3 shared publications - Ambavarapu Rafi
SMF, BARC
2 shared publications R. Harshanth
Nuclear Power Corporation India Limited
2 shared publications
Latest Publications
- 8 December 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 117
Sampling schemes for non-destructive and partially destructive tests on existing concrete structures: A critical review
- 8 December 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 117
Sampling schemes for non-destructive and partially destructive tests on existing concrete structures: A critical review
- Open Access
- 12 August 2025
- Published by Elsevier in Hydrology Research
- Vol. 56 (8) , 754-773
Machine learning approaches for predicting water quality towards climate-resilient groundwater management in southern India
- 12 August 2025
- Published by Elsevier in Hydrology Research
- Vol. 56 (8) , 754-773
Open AccessMachine learning approaches for predicting water quality towards climate-resilient groundwater management in southern India
- 3 August 2025
- Published by Springer Nature
- p. 111-122
Effect of Dissimilar Cover to Reinforcement on Different Faces of Reinforced Concrete Section
- 3 August 2025
- Published by Springer Nature
- p. 111-122
Effect of Dissimilar Cover to Reinforcement on Different Faces of Reinforced Concrete Section
- 1 August 2025
- Published by Springer Nature
- p. 315-327
Variability in Ground Response Due to Soil Stratification: A Case Study
- 1 August 2025
- Published by Springer Nature
- p. 315-327
Variability in Ground Response Due to Soil Stratification: A Case Study
- Open Access
- 1 January 2025
- Published by Wiley in Advances in Civil Engineering
- Vol. 2025 (1)
Estimation of Flexural Crack Width in Reinforced Concrete Beams Using International Codes: A Parametric Analysis
Crack width is an important parameter for concrete design, particularly from serviceability and durability considerations. This study focused on a critical comparison of the 12 formulations for estimation of maximum flexural crack, available in 13 international codes from 10 countries/geographic regions. Four common factors are: tensile stress in reinforcement, clear cover, spacing, and diameter of reinforcement; whereas the other factors were employed selectively. Using an extensive synthetic database representing a 10‐dimensional hyperspace of possible beam sections, crack widths were estimated and were subsequently analyzed to evaluate the contributions from the major factors. Up to M50, higher grade of concrete caused higher stresses and resulted in larger crack widths; this reduced thereafter, possibly due to the enhanced tensile capacity of concrete. The descriptive crack width statistics (CWS) increased monotonically for all the international codes with the increase in: cover to reinforcement; stress in the tensile steel; spacing between reinforcing bars—indicating these as very important factors. For higher diameter of reinforcement up to 28 mm diameter, CWS were higher; possibly due to the higher stress contribution from larger diameter bars. Beyond 28 mm and up to 40 mm, the higher area of reinforcement might have resulted in lower steel stress, thereby indirectly lowering CWS. The insights obtained from this critical comparative study would be invaluable in design and control of crack width flexural members through reinforcement detailing and other methods.
- 1 January 2025
- Published by Wiley in Advances in Civil Engineering
- Vol. 2025 (1)
Open AccessEstimation of Flexural Crack Width in Reinforced Concrete Beams Using International Codes: A Parametric Analysis
Crack width is an important parameter for concrete design, particularly from serviceability and durability considerations. This study focused on a critical comparison of the 12 formulations for estimation of maximum flexural crack, available in 13 international codes from 10 countries/geographic regions. Four common factors are: tensile stress in reinforcement, clear cover, spacing, and diameter of reinforcement; whereas the other factors were employed selectively. Using an extensive synthetic database representing a 10‐dimensional hyperspace of possible beam sections, crack widths were estimated and were subsequently analyzed to evaluate the contributions from the major factors. Up to M50, higher grade of concrete caused higher stresses and resulted in larger crack widths; this reduced thereafter, possibly due to the enhanced tensile capacity of concrete. The descriptive crack width statistics (CWS) increased monotonically for all the international codes with the increase in: cover to reinforcement; stress in the tensile steel; spacing between reinforcing bars—indicating these as very important factors. For higher diameter of reinforcement up to 28 mm diameter, CWS were higher; possibly due to the higher stress contribution from larger diameter bars. Beyond 28 mm and up to 40 mm, the higher area of reinforcement might have resulted in lower steel stress, thereby indirectly lowering CWS. The insights obtained from this critical comparative study would be invaluable in design and control of crack width flexural members through reinforcement detailing and other methods.
- Open Access
- 1 October 2024
- Published by IWA Publishing in Journal of Water and Climate Change
- Vol. 15 (10) , 5355-5356
Commentary on ‘Deriving location-specific synthetic seasonal hyetographs using GPM records and comparing with SCS curves' by Ram, B., Gaur, M. L., Patel, G. R. and Tiwari, M. K., published in Journal of Water and Climate Change, 15 (2), 747–758
- 1 October 2024
- Published by IWA Publishing in Journal of Water and Climate Change
- Vol. 15 (10) , 5355-5356
Open AccessCommentary on ‘Deriving location-specific synthetic seasonal hyetographs using GPM records and comparing with SCS curves' by Ram, B., Gaur, M. L., Patel, G. R. and Tiwari, M. K., published in Journal of Water and Climate Change, 15 (2), 747–758
- 4 September 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 447
Probabilistic acceptance criteria for strength of concrete produced using non-potable water for sustainable infrastructure
- 4 September 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 447
Probabilistic acceptance criteria for strength of concrete produced using non-potable water for sustainable infrastructure
- 1 August 2024
- Published by American Society of Civil Engineers (ASCE) in Practice Periodical on Structural Design and Construction
- Vol. 29 (3)
Durability Concerns for Different Clear Covers Provided to Reinforcement in Concrete Structures When Considering Different Chloride Exposure Conditions for External and Internal Faces of Members
- 1 August 2024
- Published by American Society of Civil Engineers (ASCE) in Practice Periodical on Structural Design and Construction
- Vol. 29 (3)
Durability Concerns for Different Clear Covers Provided to Reinforcement in Concrete Structures When Considering Different Chloride Exposure Conditions for External and Internal Faces of Members
- 1 July 2024
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 76 (13) , 707-722
Probabilistic effect of non-potable mixing water on characteristic strength of concrete
Across the world, the acceptance criterion for concrete made with non-potable water (SA) is stipulated for mean strength with reference to similar concrete made with potable water (SP). The basis for the strength design of concrete is the characteristic strength. The effect of the acceptance criteria on the characteristic strength of SA and SP was examined using statistical simulations, for the first time. It was found that, compared with a two-sample set, using a three-sample set would improve the characteristic strength of SA. A higher allowable ratio between the means of SA and SP and a lower deviation of individual samples from the mean would improve the characteristic strength of SA. The effect of the coefficient of variation (CoV) of the original population on the characteristic strength of SA varied. On the one hand, a higher CoV reduced the characteristic strength of SP, thereby increasing the probability of SA strength being higher than SP strength. On the other, a higher CoV of SP meant a wider spread of the samples and that could increase the CoV of SA, thereby reducing the characteristic strength of SA. Probabilistic charts were developed for the characteristic strengths of SA and SP for different combinations of the aforementioned variables, with guidance for practical application.
- 1 July 2024
- Published by Emerald Publishing in Magazine of Concrete Research
- Vol. 76 (13) , 707-722
Probabilistic effect of non-potable mixing water on characteristic strength of concrete
Across the world, the acceptance criterion for concrete made with non-potable water (SA) is stipulated for mean strength with reference to similar concrete made with potable water (SP). The basis for the strength design of concrete is the characteristic strength. The effect of the acceptance criteria on the characteristic strength of SA and SP was examined using statistical simulations, for the first time. It was found that, compared with a two-sample set, using a three-sample set would improve the characteristic strength of SA. A higher allowable ratio between the means of SA and SP and a lower deviation of individual samples from the mean would improve the characteristic strength of SA. The effect of the coefficient of variation (CoV) of the original population on the characteristic strength of SA varied. On the one hand, a higher CoV reduced the characteristic strength of SP, thereby increasing the probability of SA strength being higher than SP strength. On the other, a higher CoV of SP meant a wider spread of the samples and that could increase the CoV of SA, thereby reducing the characteristic strength of SA. Probabilistic charts were developed for the characteristic strengths of SA and SP for different combinations of the aforementioned variables, with guidance for practical application.