Luis Cifuentes
Research Subjects
Luis Cifuentes has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Algora
Instituto de Energía Solar, Universidad Politécnica de Madrid, Avda. Complutense, 30, 28040 Madrid, Spain
2 shared publications - Ignacio Rey-Stolle
Instituto de Energía Solar, ETSI de Telecomunicación, Universidad Politécnica de Madrid, 28040 Madrid, Spain
2 shared publications - Iván García
Universidad Politécnica de Madrid
2 shared publications - Iván Lombardero
Instituto de Energa Solar, Universidad Politcnica de Madrid,Madrid,Spain
2 shared publications - Alejandro Vargas-Uscategui
CSIRO Manufacturing, Clayton, Australia
1 shared publication - Andrew W. S. Johnson
Department of Physics, Benue State University, Makurdi, Nigeria
1 shared publication
Latest Publications
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Advances in Flexible and Lightweight III-V Multijunction Solar Cells for High Power Density Applications
We are developing flexible and lightweight III-V multijuntion solar cells for high power density applications such as unmanned aerial vehicles (drones), High Altitude Pseudo Satellites (HAPS) and high altitude stratospheric balloons for satellite-like communications, cheap and widespread internet connectivity, etc. We focus our research on two different types of III-V solar cells covering the range from 1 kW/kg to 3 kW/kg (considering the weight of the solar cell itself and not that of the module). Our approach to achieve a goal of 3 kW/kg is based on 3J inverted metamorphic solar cells. We have recently developed GaInP/GaAs/GaInAs 3J IMM solar cells with a power density of 5.7 kW/kg under 1xAM1.5g for small areas. Demonstrating large area devices (tens of square cm) is the next challenge to tackle. In addition, we are developing lower-cost designs, targeting 1 kW/kg, based on GaInP/Ga(In)As/Ge 3J lattice matched solar cells. In this paper we present the advances in the modelling and manufacturing of this last type of solar cell. Modelling indicates that there are multiple efficiency-thickness combinations reaching the 1 kW/kg target. For example in the case of AM1.5g, a solar thickness of 46 microns requires an efficiency of 30% which is a demanding value. However, if the thickness is reduced to 40 microns, a more easily achievable efficiency of 27% would be required. We have demonstrated a process for thinning the Ge substrates reaching thicknesses as low as 14 microns with highly homogeneous thickness profiles. Preliminary results show that the 3J thinned solar cell exhibits an efficiency which is the 91% of the efficiency achieved by the non-thinned cell.
- 11 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Advances in Flexible and Lightweight III-V Multijunction Solar Cells for High Power Density Applications
We are developing flexible and lightweight III-V multijuntion solar cells for high power density applications such as unmanned aerial vehicles (drones), High Altitude Pseudo Satellites (HAPS) and high altitude stratospheric balloons for satellite-like communications, cheap and widespread internet connectivity, etc. We focus our research on two different types of III-V solar cells covering the range from 1 kW/kg to 3 kW/kg (considering the weight of the solar cell itself and not that of the module). Our approach to achieve a goal of 3 kW/kg is based on 3J inverted metamorphic solar cells. We have recently developed GaInP/GaAs/GaInAs 3J IMM solar cells with a power density of 5.7 kW/kg under 1xAM1.5g for small areas. Demonstrating large area devices (tens of square cm) is the next challenge to tackle. In addition, we are developing lower-cost designs, targeting 1 kW/kg, based on GaInP/Ga(In)As/Ge 3J lattice matched solar cells. In this paper we present the advances in the modelling and manufacturing of this last type of solar cell. Modelling indicates that there are multiple efficiency-thickness combinations reaching the 1 kW/kg target. For example in the case of AM1.5g, a solar thickness of 46 microns requires an efficiency of 30% which is a demanding value. However, if the thickness is reduced to 40 microns, a more easily achievable efficiency of 27% would be required. We have demonstrated a process for thinning the Ge substrates reaching thicknesses as low as 14 microns with highly homogeneous thickness profiles. Preliminary results show that the 3J thinned solar cell exhibits an efficiency which is the 91% of the efficiency achieved by the non-thinned cell.
- Open Access
- 15 September 2017
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 25 (11) , 887-895
Degradation of subcells and tunnel junctions during growth of GaInP/Ga(In)As/GaNAsSb/Ge 4‐junction solar cells
A GaInP/Ga(In)As/GaNAsSb/Ge 4J solar cell grown using the combined MOVPE + MBE method is presented. This structure is used as a test bench to assess the effects caused by the integration of subcells and tunnel junctions into the full 4J structure. A significant degradation of the Ge bottom subcell emitter is observed during the growth of the GaNAsSb subcell, with a drop in the carrier collection efficiency at the high energy photon range that causes a ~15% lower Jsc and a Voc drop of ~50 mV at 1‐sun. The Voc of the GaNAsSb subcell is shown to drop by as much as ~140 mV at 1‐sun. No degradation in performance is observed in the tunnel junctions, and no further degradation is neither observed for the Ge subcell during the growth of the GaInP/Ga(In)As subcells. The hindered efficiency potential in this lattice‐matched 4J architecture due to the degradation of the Ge and GaNAsSb subcells is discussed.
- 15 September 2017
- Published by Wiley in Progress in Photovoltaics: Research and Applications
- Vol. 25 (11) , 887-895
Open AccessDegradation of subcells and tunnel junctions during growth of GaInP/Ga(In)As/GaNAsSb/Ge 4‐junction solar cells
A GaInP/Ga(In)As/GaNAsSb/Ge 4J solar cell grown using the combined MOVPE + MBE method is presented. This structure is used as a test bench to assess the effects caused by the integration of subcells and tunnel junctions into the full 4J structure. A significant degradation of the Ge bottom subcell emitter is observed during the growth of the GaNAsSb subcell, with a drop in the carrier collection efficiency at the high energy photon range that causes a ~15% lower Jsc and a Voc drop of ~50 mV at 1‐sun. The Voc of the GaNAsSb subcell is shown to drop by as much as ~140 mV at 1‐sun. No degradation in performance is observed in the tunnel junctions, and no further degradation is neither observed for the Ge subcell during the growth of the GaInP/Ga(In)As subcells. The hindered efficiency potential in this lattice‐matched 4J architecture due to the degradation of the Ge and GaNAsSb subcells is discussed.
- 1 December 2014
- Published by Elsevier in Journal of Solid State Chemistry
- Vol. 220, 17-21
Characterization of rhenium compounds obtained by electrochemical synthesis after aging process
- 1 December 2014
- Published by Elsevier in Journal of Solid State Chemistry
- Vol. 220, 17-21
Characterization of rhenium compounds obtained by electrochemical synthesis after aging process
- 1 February 2012
- Published by Elsevier in Hydrometallurgy
- Vol. 113-114, 192-194
Crystallization of sodium perrhenate from NaReO4–H2O–C2H5OH solutions at 298K
- 1 February 2012
- Published by Elsevier in Hydrometallurgy
- Vol. 113-114, 192-194
Crystallization of sodium perrhenate from NaReO4–H2O–C2H5OH solutions at 298K
- 1 May 2011
- Published by SAGE Publications in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy: Section C
- Vol. 120 (2) , 97-101
Rhenium cementation on zinc in aqueous acidic solutions
- 1 May 2011
- Published by SAGE Publications in Mineral Processing and Extractive Metallurgy: Transactions of the Institutions of Mining and Metallurgy: Section C
- Vol. 120 (2) , 97-101
Rhenium cementation on zinc in aqueous acidic solutions
- 1 July 2007
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 31 (7) , 1308-1320
Modelling a copper electrowinning cell based on reactive electrodialysis
- 1 July 2007
- Published by Elsevier in Applied Mathematical Modelling
- Vol. 31 (7) , 1308-1320
Modelling a copper electrowinning cell based on reactive electrodialysis