Ana Cimentada
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ana Cimentada has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- Carlos Thomas
LADICIM (Laboratory of Materials Science and Engineering), University of Cantabria, E.T.S. de Ingenieros de Caminos, Canales y Puertos, Av./Los Castros 44, 39005 Santander, Spain
9 shared publications - Juan Antonio Polanco
LADICIM (Laboratory of Materials Science and Engineering), Universidad de Cantabria. E.T.S. de Ingenieros de Caminos, Canales y Puertos, Av./Los Castros 44, 39005 Santander, Spain
6 shared publications - Almudena Da Costa
Group of Geotechnical Engineering, Department of Ground Engineering and Materials Science, University of Cantabria, Avda. de Los Castros, s/n, 39005 Santander, Spain
4 shared publications - Jose A. Sainz-Aja
LADICIM (Laboratory of Materials Science and Engineering), E.T.S. de Ingenieros de Caminos, Canales y Puertos, University of Cantabria, Av./Los Castros 44, 39005 Santander, Spain
3 shared publications - Pablo Tamayo
LADICIM (Laboratory of Materials Science and Engineering), University of Cantabria, E.T.S. de Ingenieros de Caminos, Canales y Puertos, Av./Los Castros 44, 39005 Santander, Spain
3 shared publications - Ali Aghajanian
Dept. of Civil Engineering, Univ. of Tehran - International Campus, Niyayesh St., Mirmohanna Blvd., Kish Island, Iran. ORCID:
2 shared publications
Latest Publications
- 1 January 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 39 (1) , 04026516
Synergistic Effects of EAF Slag Aggregate, Silica Fume, and Fibers on Mechanical and Microstructural Performance of Sustainable Concrete
This study evaluates concrete in which natural aggregates (NAs) are replaced by electric arc furnace (EAF) slag siderurgical aggregate (SA), with partial cement replacement by silica fume and reinforcement using steel and polypropylene fibers. Mechanical tests (compressive and flexural) at 7, 28, and 90 days and microstructural analyses (SEM/EDS) of the interfacial transition zone (ITZ) were conducted. Optimal mixes containing 8% silica fume and 0.6% fiber volume exhibited an average ITZ thickness reduction from 27.8 ± 3.2 μ m (control) to 15.4 ± 2.1 μ m ( n = 20 fields), and compressive strength gains of up to 21% at 28 days (and up to 30% at 90 days for SA-C-100 mixes). Statistical significance was assessed using one-way ANOVA. These results demonstrate the synergistic effect of SA, silica fume, and fibers on densifying the ITZ and improving flexural toughness, and provide practical recommendations for mass concrete applications.
- 1 January 2027
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 39 (1) , 04026516
Synergistic Effects of EAF Slag Aggregate, Silica Fume, and Fibers on Mechanical and Microstructural Performance of Sustainable Concrete
This study evaluates concrete in which natural aggregates (NAs) are replaced by electric arc furnace (EAF) slag siderurgical aggregate (SA), with partial cement replacement by silica fume and reinforcement using steel and polypropylene fibers. Mechanical tests (compressive and flexural) at 7, 28, and 90 days and microstructural analyses (SEM/EDS) of the interfacial transition zone (ITZ) were conducted. Optimal mixes containing 8% silica fume and 0.6% fiber volume exhibited an average ITZ thickness reduction from 27.8 ± 3.2 μ m (control) to 15.4 ± 2.1 μ m ( n = 20 fields), and compressive strength gains of up to 21% at 28 days (and up to 30% at 90 days for SA-C-100 mixes). Statistical significance was assessed using one-way ANOVA. These results demonstrate the synergistic effect of SA, silica fume, and fibers on densifying the ITZ and improving flexural toughness, and provide practical recommendations for mass concrete applications.
- 12 November 2026
- Published by Santander. Estudios de Patrimonio. Editorial de la Universidad de Cantabria
Piedras duras, gemas y vidrios: emulación y lujo desde la época antigua a la moderna
The purpose of this volume is to present the results of the (research) project Imitations of Stones in Glass in the Roman Period and Their Reinterpretation in Modern Times (PID2020-117299GB-I00), funded by the Ministry of Science, Innovation and Universities, State Research Agency, which aimed to delve into a transversal practice in History, which has taken place throughout all (historical) periods and that continues up to our days such as the imitation of precious and ornamental stones using glass. This is a practice linked to ostentation and luxury but at the same time it is connected with issues of forgery and a wide range of conceptually intermediate products. Throughout history, hard and precious stones were only accessible to the elites, and they were imitated, copied or counterfeited using more economical materials—among which glass stands out—popularizing their use, which does not mean, however, their universalization. But glass was also used to embellish objects made of metal, ceramic, wood, bone (and other materials), significantly increasing their artistic value and claiming a rightful place within the sphere of luxury goods. The contributions presented in this volume analyse philological, archaeological, historical-artistic and archaeometric aspects across different periods. The authors—specialist researchers from Spain, Italy, and the United Kingdom—address general overviews of the subject in the different historical periods and they also study objects made from hard and precious stones, and at the same time their imitations in glass. The designs of these stones can be found in personal adornments, decorative elements and the domestic furnishings of the elites, which gradually spread to other strata of society through imitations of varying quality, depending on the economic means of the customer and the craftsman’s skill. Some of these imitations reached the status of unique objects, even becoming as valuable as the object they replicated. Likewise, some stone manufactures from antiquity were later repurposed for liturgical use or which ended up in collections of prominent patrons. This transfer shows an interest in antiquity and a desire to establish a connection with the past, but it also shows the will of displaying a refined taste and the owner's power. Moreover, these ancient pieces were often used as models for later creations, sometimes crafted in the same raw material, therefore enhancing the ideological message conveyed by the copy. They were also used as models for the production of more affordable copies made from different materials, repeating an imitation pattern which was already known from antiquity, reworking the symbolic value, in some cases to adapt it to the new historical context, being the connection the connotation of economic and social prestige that such reuse entailed within an assessment of the ancient world.
- 12 November 2026
- Published by Santander. Estudios de Patrimonio. Editorial de la Universidad de Cantabria
Piedras duras, gemas y vidrios: emulación y lujo desde la época antigua a la moderna
The purpose of this volume is to present the results of the (research) project Imitations of Stones in Glass in the Roman Period and Their Reinterpretation in Modern Times (PID2020-117299GB-I00), funded by the Ministry of Science, Innovation and Universities, State Research Agency, which aimed to delve into a transversal practice in History, which has taken place throughout all (historical) periods and that continues up to our days such as the imitation of precious and ornamental stones using glass. This is a practice linked to ostentation and luxury but at the same time it is connected with issues of forgery and a wide range of conceptually intermediate products. Throughout history, hard and precious stones were only accessible to the elites, and they were imitated, copied or counterfeited using more economical materials—among which glass stands out—popularizing their use, which does not mean, however, their universalization. But glass was also used to embellish objects made of metal, ceramic, wood, bone (and other materials), significantly increasing their artistic value and claiming a rightful place within the sphere of luxury goods. The contributions presented in this volume analyse philological, archaeological, historical-artistic and archaeometric aspects across different periods. The authors—specialist researchers from Spain, Italy, and the United Kingdom—address general overviews of the subject in the different historical periods and they also study objects made from hard and precious stones, and at the same time their imitations in glass. The designs of these stones can be found in personal adornments, decorative elements and the domestic furnishings of the elites, which gradually spread to other strata of society through imitations of varying quality, depending on the economic means of the customer and the craftsman’s skill. Some of these imitations reached the status of unique objects, even becoming as valuable as the object they replicated. Likewise, some stone manufactures from antiquity were later repurposed for liturgical use or which ended up in collections of prominent patrons. This transfer shows an interest in antiquity and a desire to establish a connection with the past, but it also shows the will of displaying a refined taste and the owner's power. Moreover, these ancient pieces were often used as models for later creations, sometimes crafted in the same raw material, therefore enhancing the ideological message conveyed by the copy. They were also used as models for the production of more affordable copies made from different materials, repeating an imitation pattern which was already known from antiquity, reworking the symbolic value, in some cases to adapt it to the new historical context, being the connection the connotation of economic and social prestige that such reuse entailed within an assessment of the ancient world.
- Open Access
- 8 March 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (6) , 3436
Effect of Recycled Foundry Sand on the Workability and Mechanical Properties of Mortar
Modern society requires a large number of metal components manufactured by sand casting, which involves the generation of a waste product known as Used Foundry Sand (UFS), of which approximately 100 Mt are generated on an annual basis. Virtually all UFS is currently landfilled, despite the economic and environmental cost overruns that this entails. Here, the recovery of UFS as fine aggregates for the manufacture of concrete is proposed. Since the presence of UFS will mainly affect the mortar that binds the aggregates in the manufacture of concrete, it was decided to isolate this fraction and study only the effect of UFS in mortars. This study evaluated a total of 32 different mixes combining different W/C ratios varying between 0.5 and 0.7 with 5 replacement ratios of natural sand by UFS: 0, 25, 50, 75 and 100%, respectively. The combined effect was evaluated of the W/C ratio and the replacement ratio on the workability, physical properties, mechanical properties, mechanical durability, and microstructure of the mortars. The incorporation of UFS decreases the workability of the mortars due to the absorption of the residue. For the physical properties of the mortars, density decreased and porosity and absorption increased at all replacement percentages. Flexural and compressive strength decreased when the replacement percentage was higher than 25 wt.%. In terms of mechanical durability, the mortars with UFS showed abrasion marks within the limits of the EN-1338 standard. From the results obtained, it is possible to conclude that the mortars with UFS require a higher amount of water. Therefore, while small replacement levels lead to a slight improvement in the mechanical properties, this trend breaks down for high replacement levels due to the negative effect of the high W/C ratios required. The authors recommend that for replacements higher than 25 wt.% of UFS, the W/C ratio has to be taken into consideration to obtain the same workability as the control mortar, although this decreases the mechanical properties.
- 8 March 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (6) , 3436
Open AccessEffect of Recycled Foundry Sand on the Workability and Mechanical Properties of Mortar
Modern society requires a large number of metal components manufactured by sand casting, which involves the generation of a waste product known as Used Foundry Sand (UFS), of which approximately 100 Mt are generated on an annual basis. Virtually all UFS is currently landfilled, despite the economic and environmental cost overruns that this entails. Here, the recovery of UFS as fine aggregates for the manufacture of concrete is proposed. Since the presence of UFS will mainly affect the mortar that binds the aggregates in the manufacture of concrete, it was decided to isolate this fraction and study only the effect of UFS in mortars. This study evaluated a total of 32 different mixes combining different W/C ratios varying between 0.5 and 0.7 with 5 replacement ratios of natural sand by UFS: 0, 25, 50, 75 and 100%, respectively. The combined effect was evaluated of the W/C ratio and the replacement ratio on the workability, physical properties, mechanical properties, mechanical durability, and microstructure of the mortars. The incorporation of UFS decreases the workability of the mortars due to the absorption of the residue. For the physical properties of the mortars, density decreased and porosity and absorption increased at all replacement percentages. Flexural and compressive strength decreased when the replacement percentage was higher than 25 wt.%. In terms of mechanical durability, the mortars with UFS showed abrasion marks within the limits of the EN-1338 standard. From the results obtained, it is possible to conclude that the mortars with UFS require a higher amount of water. Therefore, while small replacement levels lead to a slight improvement in the mechanical properties, this trend breaks down for high replacement levels due to the negative effect of the high W/C ratios required. The authors recommend that for replacements higher than 25 wt.% of UFS, the W/C ratio has to be taken into consideration to obtain the same workability as the control mortar, although this decreases the mechanical properties.
- Open Access
- 14 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2439
Fatigue Behaviour of Concrete Using Siderurgical Aggregates
The use of concrete with aggregates with reduced environmental impact, as is the case of concrete with siderurgical aggregates (recovered slags), will inevitably increase in the future, as a result of policies promoting development of more sustainable construction materials. These concretes offer an excellent response to static loads, but their behaviour under dynamic loads has not yet been studied. The aim of this study is to characterize the fatigue behaviour, in terms of fatigue limit, of a concrete with siderurgical aggregates by comparing it with an analogous conventional limestone concrete. This characterization was carried out using the Locati method, which stands out for its convenience, speed and low cost, with the feature of being carried out at a high frequency corresponding to the resonance frequency. Performing high-frequency tests has drastically reduced test times and thus costs. Likewise, the results obtained show that, using various criteria found in the literature, concrete with siderurgical aggregates has a higher fatigue limit in absolute terms (MPa), but a lower one in relative terms (% fc).
- 14 February 2023
- Published by MDPI AG in Applied Sciences
- Vol. 13 (4) , 2439
Open AccessFatigue Behaviour of Concrete Using Siderurgical Aggregates
The use of concrete with aggregates with reduced environmental impact, as is the case of concrete with siderurgical aggregates (recovered slags), will inevitably increase in the future, as a result of policies promoting development of more sustainable construction materials. These concretes offer an excellent response to static loads, but their behaviour under dynamic loads has not yet been studied. The aim of this study is to characterize the fatigue behaviour, in terms of fatigue limit, of a concrete with siderurgical aggregates by comparing it with an analogous conventional limestone concrete. This characterization was carried out using the Locati method, which stands out for its convenience, speed and low cost, with the feature of being carried out at a high frequency corresponding to the resonance frequency. Performing high-frequency tests has drastically reduced test times and thus costs. Likewise, the results obtained show that, using various criteria found in the literature, concrete with siderurgical aggregates has a higher fatigue limit in absolute terms (MPa), but a lower one in relative terms (% fc).
- Open Access
- 24 November 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 64, 105543
Microstructural analysis of siderurgical aggregate concrete reinforced with fibers
- 24 November 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 64, 105543
Open AccessMicrostructural analysis of siderurgical aggregate concrete reinforced with fibers
- Open Access
- 23 February 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (4) , 1957
Viability of Cupola Slag as an Alternative Eco-Binder and Filler in Concrete and Mortars
Obtaining new materials capable of meeting society’s demands motivates the search for new solutions that are capable of satisfying twofold requirements: respect for the environment and obtaining more durable and resistant materials. Cupola slag is a by-product generated in the process of obtaining ductile iron. When the slag undergoes rapid cooling, its vitrification is favored, leaving the silica in an amorphous structure and, thus, susceptible to reacting. Through reaction, the slag can develop cementing properties and cement can consequently be partially replaced with residue, providing savings in economic and environmental costs compared to traditional hydraulic binders. In this study, the physical and chemical properties of cupola slag and its recovery process are analyzed. Mortars that incorporate traditional admixtures (fly ash and limestone filler) have been manufactured and consistency and mechanical properties have been compared with mortars that incorporate cupola slag admixture. Mortars have also been manufactured with normalized sand and with Portland cement replacements (0, 10, 20, and 30% by weight) with cupola slag, and both the consistency and the mechanical properties have been compared at 7, 28, 60, and 90 days. The results obtained show the suitability of cupola slag as a binder and as an admixture, with respect to the traditional ones, and how the mechanical properties tend to converge for all of the replacement levels characterized, for ages close to 90 days of age.
- 23 February 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (4) , 1957
Open AccessViability of Cupola Slag as an Alternative Eco-Binder and Filler in Concrete and Mortars
Obtaining new materials capable of meeting society’s demands motivates the search for new solutions that are capable of satisfying twofold requirements: respect for the environment and obtaining more durable and resistant materials. Cupola slag is a by-product generated in the process of obtaining ductile iron. When the slag undergoes rapid cooling, its vitrification is favored, leaving the silica in an amorphous structure and, thus, susceptible to reacting. Through reaction, the slag can develop cementing properties and cement can consequently be partially replaced with residue, providing savings in economic and environmental costs compared to traditional hydraulic binders. In this study, the physical and chemical properties of cupola slag and its recovery process are analyzed. Mortars that incorporate traditional admixtures (fly ash and limestone filler) have been manufactured and consistency and mechanical properties have been compared with mortars that incorporate cupola slag admixture. Mortars have also been manufactured with normalized sand and with Portland cement replacements (0, 10, 20, and 30% by weight) with cupola slag, and both the consistency and the mechanical properties have been compared at 7, 28, 60, and 90 days. The results obtained show the suitability of cupola slag as a binder and as an admixture, with respect to the traditional ones, and how the mechanical properties tend to converge for all of the replacement levels characterized, for ages close to 90 days of age.
- Open Access
Study of Hillock and Zinc Whisker Evolution in Five Different Cable Tray Coatings
The main objective of this work is the study of the hillock and zinc whisker evolution of five different commercial zinc coatings applied on the same base steel wires of the patented EASYCONNECT system cable trays manufactured by VALDINOX Ltd.: white zinc alkaline electrolyte, yellow zinc trivalent electrolyte, acid zinc electrolyte, hot dip galvanized, and zinc nickel coating. The limited literature on the subject is summarized, and then the coating thickness, chemical composition, hardness and surface rugosity are characterized. The hillock and whisker density evolution are evaluated over a period of 12 months, considering the presence of compression bending stresses. It is concluded that the white alkaline and yellow trivalent coatings are the most affected, while the zinc-nickel shows the best behavior with no presence of whiskers; the acid zinc electrolyte also shows good results despite the delayed appearance of whiskers from the ninth month; the hot-dip galvanized coating does not show any presence of zinc whiskers or hillocks.
Open AccessStudy of Hillock and Zinc Whisker Evolution in Five Different Cable Tray Coatings
The main objective of this work is the study of the hillock and zinc whisker evolution of five different commercial zinc coatings applied on the same base steel wires of the patented EASYCONNECT system cable trays manufactured by VALDINOX Ltd.: white zinc alkaline electrolyte, yellow zinc trivalent electrolyte, acid zinc electrolyte, hot dip galvanized, and zinc nickel coating. The limited literature on the subject is summarized, and then the coating thickness, chemical composition, hardness and surface rugosity are characterized. The hillock and whisker density evolution are evaluated over a period of 12 months, considering the presence of compression bending stresses. It is concluded that the white alkaline and yellow trivalent coatings are the most affected, while the zinc-nickel shows the best behavior with no presence of whiskers; the acid zinc electrolyte also shows good results despite the delayed appearance of whiskers from the ninth month; the hot-dip galvanized coating does not show any presence of zinc whiskers or hillocks.
- Open Access
- 23 September 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (19) , 6655
Industrial Low-Clinker Precast Elements Using Recycled Aggregates
Increasing amounts of sustainable concretes are being used as society becomes more aware of the environment. This paper attempts to evaluate the properties of precast concrete elements formed with recycled coarse aggregate and low clinker content cement using recycled additions. To this end, six different mix proportions were characterized: a reference concrete; 2 concretes with 25%wt. and 50%wt. substitution of coarse aggregate made using mixed construction and demolition wastes; and others with recycled cement with low clinker content. The compressive strength, the elastic modulus, and the durability indicator decrease with the proportions of recycled aggregate replacing aggregate, and it is accentuated with the incorporation of recycled cement. However, all the precast elements tested show good performance with slight reduction in the mechanical properties. To confirm the appropriate behaviour of New Jersey precast barriers, a test that simulated the impact of a vehicle was carried out.
- 23 September 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (19) , 6655
Open AccessIndustrial Low-Clinker Precast Elements Using Recycled Aggregates
Increasing amounts of sustainable concretes are being used as society becomes more aware of the environment. This paper attempts to evaluate the properties of precast concrete elements formed with recycled coarse aggregate and low clinker content cement using recycled additions. To this end, six different mix proportions were characterized: a reference concrete; 2 concretes with 25%wt. and 50%wt. substitution of coarse aggregate made using mixed construction and demolition wastes; and others with recycled cement with low clinker content. The compressive strength, the elastic modulus, and the durability indicator decrease with the proportions of recycled aggregate replacing aggregate, and it is accentuated with the incorporation of recycled cement. However, all the precast elements tested show good performance with slight reduction in the mechanical properties. To confirm the appropriate behaviour of New Jersey precast barriers, a test that simulated the impact of a vehicle was carried out.
- 1 March 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 59, 260-268
Epoxy composites containing CFRP powder wastes
- 1 March 2014
- Published by Elsevier in Composites Part B: Engineering
- Vol. 59, 260-268
Epoxy composites containing CFRP powder wastes