OUOleksandr Usatyi

Oleksandr Usatyi

*This is an algorithmically generated author record based on publicly available information.

Oleksandr Usatyi has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Mathematical Modeling and Computational Research of Thermo- and Gas-Dynamic Processes in Damaged Flow Parts of Steam Turbines

    by Oleksandr Usatyi, Anton Klob

    The difficult state of the Ukrainian power system, caused by damage to the power generating equipment of many thermal power plants, is characterized by a significant deficit of domestically produced electricity. The degree of damage to the flow parts of power steam turbines is characterized by diversity in terms of the location of the damage and its scale. Among the damaged turbines, there are some that, subject to preventive repair work, can be used in the process of generating electricity at lower loads. To assess the possibility of use, as well as to assess the required level of load reduction for such turbines, the mathematical model of thermo and gas-dynamic processes in the flow parts has been further improved. Based on the improved mathematical model and developed algorithms, test calculations of the flow part of the high-pressure cylinder of the K-310-240 steam turbine were performed with modeling of various damage variants, namely the absence of nozzle and/or working grids in several stages simultaneously. The conducted computational studies allowed us to assess the impact on the possibility and degree of rationality of further operation of the turbine cylinder and determine the level of its load depending on the variant of damage to the flow part.

  • Development of a Mathematical Model, Software and Computational Studies to Assess the Potential of Local Gas Networks Regarding the Feasibility of Using Turboexpanders

    by Oleksandr Usatyi, Maxim Novikov, Mykhdilo Daluain, Eugene Mischanenko

    Given the fact that turboexpander installations provide distributed electricity production without harmful effects on the environment, the energy sector of Ukraine is faced with the task of the widest possible implementation of turboexpander technologies. To determine the most suitable local gas networks for the implementation of turboexpander technologies, which operate with natural gas of different component composition, different pressures and temperatures and gas mass flows, it is necessary to have the ability to conduct a rapid expert assessment of the potential of these gas networks regarding the possibility and rationality of implementing turboexpander technologies for electricity production. The article presents a mathematical model for estimating the power of a turboexpander as a function of the main parameters of natural gas of the local gas network and the internal relative efficiency of the turboexpander. An example of a software implementation of the mathematical model in the C++ programming language is given. A software implementation of solving the equations of state of multicomponent mixtures of natural gas for four local gas networks of Ukraine is shown. The results of numerical studies of the influence of natural gas parameters and efficiency on the power that can be obtained when using turboexpanders are presented, and a comparative analysis of local gas networks in terms of obtaining the maximum power of turboexpanders is also performed. The developed software can be useful both for turboexpander manufacturers and customers for conducting rapid expert assessments of the potential of local gas networks and gas fields in terms of the feasibility of using turboexpanders.

  • The Problem of Assessing the Reliability and Residual Resource of Long-Term Operating Welded Joints in Steam Pipelines of Thermal Power Plants

    by Віталій Дмитрик, Xinlei Chen, Oleksandr Usatyi, Ihor Kasianenko, Сіньлей Чень, Ігор Касьяненко

    Assessing the reliability of welded joints of steam pipelines made of heat-resistant pearlitic steels that are operated for a long time (over 270 thousand hours) under creep and fatigue conditions, has become an extremely relevant issue. The purpose of this research is to determine the avenues for the development of regulatory provisions regarding the reliability of welded joints of steam pipelines that are operated for a long time under creep and fatigue conditions. To achieve the goal, appropriate methods of research and analysis were used to study the structural-&-phase state and determine the chemical composition and physical-&-mechanical properties of the metal of welded joints, as well as the level of their damageability. It was established that the damageability of the metal of welded joints depends primarily on its structural-&-phase state. With an increase in the operating time of welded joints, a ferrite-carbide mixture is gradually formed in their initial structure, and accordingly, and the amount of it as its component is increased. The presence of such a mixture contributes to the damageability of welded joints. which follows creep and fatigue mechanisms. The feasibility of detecting a ferrite-carbide mixture in the structure of welded joints by using already improved techniques and developing new quality control methods has been substantiated. To obtain appropriate results, we propose improving the quality control methods for welded joints of steam pipelines that operate for a long time under creep and fatigue conditions. We substantiated that when developing new and improving standard methods for quality control of metal of welded joints that operate for a long time under creep and fatigue conditions, it is necessary to consider their structural and phase state, which will increase the reliability of the operation of welded joints. Improving the technologies already available as well as developing new methods and techniques for quality control of metal of steam pipelines and their welded joints, will allow us to improve the assessment of their structural and phase state and the presence of damages. Considering the results obtained in relation to new regulatory provisions will allow us to improve the assessment of the reliability of aging steam pipelines and their welded joints, as well as to determine their residual resource.

  • Open Access

    Search and Analysis of the Methods to Increase the Power and Efficiency of Turboexpanders Operating on a Natural Gas Mixture

    by Oleksandr Usatyi, Maxim Novikov, Максим Новіков

    The compressed natural gas energy is one of the highly efficient modern alternative technologies used for generating electric power causing no realistic damage to the environment. This type of gas is used as a working fluid, in particular for axial turboexpanders. Ukraine has significant natural gas deposits and an extensive network of main pipelines for pumping gas under high pressure. Therefore, increasing the efficiency of converting compressed natural gas energy into mechanical work to drive electric generators is an important and urgent task. This scientific paper presents the data of the analysis of the effect of the main geometric parameters of the flow parts of axial turboexpanders on their efficiency. An improved mathematical model of one-dimensional flow in the flow part and an algorithm that implements it in the TurboOptProject (TOP) software package were used to conduct computational studies. The algorithms that describe the equation of state of a 9-component mixture of natural gas in the range of changes in the parameters that correspond to the operating conditions of the initial and optimal options of the turboexpander have been developed. The interaction and the effect of the leaks into the end seals of the control system of the axial force on rotor on the efficiency of the flow part have also been taken into account. To obtain the optimal variant of the turboexpander, the optimization algorithm for multi-level optimization of composite technical objects has been improved. The computational studies and the analysis of the obtained data have shown the possibility of increasing the power of the optimal option of the flow part of the turboexpander by 125.81 kW (from 1608.86 kW to 1734.67 kW), and the relative internal efficiency factor by 6.17 % (from 77.34 % to 83.51 %) as compared to the initial option of the flow part.

  • Open Access

    Using the Theory of Competitive Distribution of Limited Resources to Assess the Degree of Rationality of Distribution of the Existing Thermal Difference between Turbine Stages

    by Riza Sherfedinov, Oleksandr Usatyi, Різа Шерфедінов

    For the problems of analysis and optimal design of the flow parts of steam turbines, an alternative method has been developed for distributing the existing thermal difference of a multistage turbine between its stages. Consideration was given to the possibility of using the theory of competitive distribution of limited resources to assess the degree of rationality of the distribution of the existing thermal difference between turbine stages. The method uses an appropriate relationship to estimate the power degree of the turbine and competitive mechanisms that were developed and used to solve resource allocation problems in the field of economics. Comparative computational studies have been carried out to assess the degree of rationality of the distribution of the existing thermal difference between the stages for the original and optimal options of the flow parts of steam turbines. The possibility of using the theory of distribution of limited resources for problems of analysis and assessment of the degree of rationality of the distribution of the existing thermal difference between the stages of the turbine and for optimization problems in order to achieve a maximum power of a multi-stage turbine has been confirmed. It is shown that the distribution of the existing thermal difference between the turbine stages for the optimal variants of flow parts has better approximations to the values of the indicators that correspond to the ideal option of the distribution of the existing thermal difference between the stages in accordance with the developed method in comparison to the original option of the turbine flow part. The developed method provides an ideal theoretical solution for assessing the degree of approximation to it, both for the original and approximately optimal flow parts of multi-stage turbines.

  • Open Access

    Numerical Study of the Effect of a Change in the Angle of Attack on the Value of the Kinetic Energy Loss Coefficient and Flow Exit Angles for Nozzle Arrays with Rotary Diaphragms

    by Oleksandr Zhyrkov, Oleksandr Usatyi, Olena Avdieieva, Yuri Torba, Юрій Торба

    The goal of one of the steps of this research is to develop a technique for numerical study of the flow around a nozzle array with a rotary diaphragm, for its further use for solving the problem of optimal design of the flow part of heating turbines. Due to an ample amount of numerical studies, the development of the methods is divided into several parts. The paper presents some results of numerical studies of flat flow around a nozzle array with a rotating diaphragm at angles of flow entry into the array of S-9013R profiles different from the calculated angle of attack equal to 90°. Modeling and calculation of the flow of the working fluid was performed using the Fluent software package. The construction of computational domains restricted by one interblade channel was carried out for different degrees of opening of the diaphragm of the nozzle apparatus. Grids for computational domains have been constructed. Calculations were carried out for the angles of entry into the profile grid in the range of 45º to 135º. The calculations done enabled the generation of flow patterns in the interblade channel and behind it, and the distribution of kinetic energy loss coefficients along the front of the array at various degrees of opening of the diaphragm at the entrance to the nozzle apparatus. Based on the results of the work done, the following conclusions can be drawn: a change in the angle of attack affects the distribution of static pressure along the profile only in its front part, and does not affect the distribution in the output part; a change in the angles of attack does not affect the exit angles from the nozzle array of S-9013R profiles; a decrease in the pressure difference across the nozzle array results in a change in the exit angles from the nozzle array at an opening degree of the rotary diaphragm of π > 0.5.

  • Open Access

    Further Improvement of the Mathematical Model of Thermo and Gas-Dynamic Processes in a Turbine without Working Blades of Some Stages

    by Oleksandr Usatyi, Антон Кльоб

    The current state of the Ukrainian power system is characterized by significant stress and a shortage of generating capacities. Restoration and implementation of new generating capacities require a huge amount of appropriate resources and a lot of time. The optimal low-cost and relatively fast option for improving the state of the power system may be the temporary use of damaged power equipment after taking appropriate preventive and repair measures. The emergency state of steam turbines of many power plants requires a special tool for assessing their efficiency and power, as well as the possibility and feasibility of their further use after damage. This paper gives consideration to an improved mathematical model of thermo and gas-dynamic processes in a turbine without working blades of some stages. The test calculation data obtained for the flow parts of the cylinders of various steam turbines in the absence of working blades were presented both for individual stages and the groups of stages. Characteristic patterns of the effect of the location of the stage without working blades in the turbine cylinder on the efficiency of the flow part have been established. The greatest decrease in the efficiency and power of the cylinder occurs in the case of the absence of working blades in the stages located closer to the cylinder head. The lowest efficiency and power losses are observed in the absence of working blades of the last stage. In the nozzle cascades of the stages located directly behind the stages without working blades, the levels of energy losses are increased significantly. The use of the developed mathematical model allows us to find solutions to increase the efficiency of turbines with missing working blades in some stages by changing the geometry of the appropriate nozzle cascades.


  • Open Access

    Prolongation of Safe Operation of the K-1000-60/3000 Turbine Power Unit after Damage to the HPC Rotor

    by National Technical University of Ukraine Igor Sikorsky Kyiv Polytechnic Institute, Olha Yu. Chernousenko, Vitalii A. Peshko, Oleksandr P. Usatyi, National Technical University Kharkiv Polytechnic Institute

    Currently, when large-scale military actions are taking place on the territory of Ukraine, the inclusion of the domestic energy system in the European one is a reliable component of providing electricity to the country's energy market. However, according to experts, uninterrupted and safe operation of nuclear power plants is still considered a prerequisite for the stable operation of the energy sector of Ukraine. The purpose of the paper is to assess the damageability and individual resource of the rotor of high-pressure cylinder (HPC) of the K-1000-60/3000 turbine power unit of the LMZ after damage to the blades in order to prolong the operation of the power unit in the conditions of a stressed state of the power system. One of the most effective ways to partially solve the problem of replacement of generating capacities is to extend the operating periods of NPP power units after the end of the project operating period, provided that nuclear and radiation safety standards are met. The review of the previously established service life of the energy equipment of NPP power units involves the assessment of the residual resource of the energy equipment in accordance with the regulatory documents. After the accidental damage of the blades of the last stage of the HPC rotor of the K-1000-60/3000 turbine power unit of the LMZ, there was a need to study the cyclic and static damage, the individual residual resource of the HPC rotor. In the process of achieving the goal, studies were carried out for three design options: the original option (five stages of the HPC rotor), the option without the blades of the last stage and the option without the fifth stage (with four first stages). The calculation of the resource indicators of the rotor in the execution of the HPC without blades of the 5th stage shows that the static damage accumulated in the main metal is 52%, the cyclic damage is 5% when applying the standard strength reserves for the number of cycles and for deformations at the level of nN=10 and nε=1.5 according to the recommendations of SOU-N MEV 40.1-21677681-52:2011. Thus, the total damage to the base metal is 57%, which sets the residual resource of the HPC rotor at the level of 88.4 thousand hours. The calculation of the resource indicators of the rotor in the execution of the HPC without entire 5th stage shows that the static damage accumulated in the base metal is 52%, the cyclic damage is 6% when applying the standard strength reserves for the number of cycles and deformations at the above-mentioned level. The total damage to the base metal is 58%, which determines the residual resource of the HPC rotor at the level of 85.6 thousand hours.


  • DETERMINING THE OPTIMUM POWER OF AN ABSORPTION HEAT PUMP WHEN IT INTEGRATING TO PT-60/70-130/13 THERMAL SCHEME

    by Олександр Леонідович Шубенко, Oleksandr Usatyi, Микола Юрійович Бабак, Yana Forkun, Oleksandr Senetskyi, Яна Борисівна Форкун

    The problem of determining the optimal thermal power of an absorption heat pump with steam heating at one-stage regeneration (COP = 1.71) is solved. The heat pump is integrated into the thermal scheme of PT-60/70-130/13 steam turbine. The heat supply schedule for this steam turbine cycle is 150/70 °С. The installation also produces steam for technological needs. The thermal and flow rate characteristics of an absorption heat pump are determined using the constructed and proposed approximation mathematical model. Based on the analysis and existing experience, an optimization problem was formulated. The goal function is to select the integrated absorption heat optimal power pump with the condition of optimal energy fuel consumption. The search for the optimal thermal power of an absorption heat pump was carried out under the condition of steam release through a controlled production turbine extraction with parameters of 1.296 MPa, 280 °C. Options for variable steam consumption for process needs (0, 20, 50 and 80 t/h) were considered. The condition was constancy of consumption throughout the year. The results obtained showed that, relative to all considered turbine loading modes, the optimal power value of the absorption heat pump is identical and amounts to ~ 17.25 MW. Calculation studies have shown that at a cost of electricity of 0.13 USD/(kWh) and equivalent fuel of 309 USD/t, a power unit with PT-60/70-130/13 turbine and an integrated absorption heat pump (thermal power 15–18 MW) with a production load of more than 20 t/h of steam, as well as a consumption of recycled network water for heat supply of more than ~ 1550 t/h, the payback of the energy saving project will be achieved in less than 3 years. The next positive effect is that fuel savings can reduce CO2 emissions by 9321 tons and NOx by 48 tons. According to research results, we observe a positive environmental effect from the integration of an absorption heat pump into the existing thermal scheme. Вирішується задача визначення оптимальної теплової потужності абсорбційного теплового насоса з паровим нагріванням при одноступеневій регенерації (СОР = 1,71). Розглядуваний тепловий насос інтегрований в теплову схему парової турбіни ПТ-60/70-130/13. Графік теплопостачання для даного паротурбінного циклу становить 150/70 °С. Також установкою виробляється пар на технологічні потреби. Визначення теплових та витратних характеристик абсорбційного теплового насоса здійснюється з використанням побудованої та запропонованої апроксимаційної математичної моделі. На підставі проведеного аналізу та наявного досвіду сформульовано оптимізаційну задачу. Функцією мети є вибір оптимальної потужності інтегрованого абсорбційного теплового насоса за умови оптимальної витрати енергетичного палива. Пошук оптимальної теплової потужності абсорбційного теплового насоса здійснювався за умови відпуску пари через регульований виробничий відбір турбіни з параметрами 1,296 МПа, 280 °С. Були розглянуті варіанти для змінної витрати пари на технологічні потреби (0, 20, 50 та 80 т/год). Умовою була постійність витрати протягом року. Отримані результати показали, що щодо всіх розглянутих режимів завантаження турбіни, оптимальне значення потужності абсорбційного теплового насоса є ідентичним і становить ~ 17,25 МВт. Розрахункові дослідження показали, що за вартості електроенергії 0,13 дол./(кВт·ч) та умовного палива 309 дол./т енергоблок з турбіною ПТ-60/70-130/13 та інтегрований абсорбційний тепловий насос (тепловою потужністю 15–18 МВт) при виробничому навантаженні понад 20 т/год пари, а також витраті оборотної мережної води на теплопостачання понад 1550 т/год дозволить отримати окупність проекту енергозбереження менше 3 років. Наступним позитивним ефектом є те, що економія палива дозволяє знизити викиди СО2 на 9321 т і NOx на 48 т. За результатами досліджень спостерігаємо позитивний екологічний ефект від інтеграції абсорбційного теплового насоса в існуючу теплову схему.