Olena Avdieieva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olena Avdieieva has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Usatyi
Національний технічний університет «Харківський політехнічний інститут
8 shared publications - Alexander Yudin
National technical university «Kharkiv polytechnic institute
3 shared publications - Artem Babaiev
National technical university «Kharkiv polytechnic institute
3 shared publications Iryna Mykhailova
National Technical University “Kharkiv Polytechnic Institute
3 shared publications- Oleksandr Zhyrkov
ДП «Івченко-Прогрес
3 shared publications - Valentyn Barannik
National technical university «Kharkiv polytechnic institute
3 shared publications
Latest Publications
- Open Access
Modeling Bass Guitar String Vibration with Frequency- and Fret-Dependent Damping for Real-Time Sound Generation
This paper presents a linear mathematical model of bass guitar string vibration with experimentally identified, frequency- and fret-dependent modal damping, aimed at high-fidelity generative sound synthesis. To identify the string damping parameters across various frets and configurations, an experimental framework was developed to benchmark four structural identification methods: half-power bandwidth, I. Yoshida’s method, Discrete Fourier Transform Interpolation, and Hilbert-transform envelope approximation. Experiments were systematically conducted on Cort C4H, Ibanez RB 630, and Yamaha bass guitars. Based on the extracted parameter space, two audio generation strategies are formulated: a spectrum-driven harmonic reconstruction method (Method 1) and a physical modeling approach utilizing spatial wave equations (Method 2). The proposed linear approximation framework effectively captures the inverse relationship between the damping factor and fret numbers specifically on the E-string, while mapping linear increases on the G and D-strings. Quantitative verification using Sobolev norm differences demonstrates good agreement between the synthesized and original signals for the spectrum-driven method (Q = 0.031–0.057) and moderate agreement for the physics-based wave equation method (Q = 0.058–0.153). This reflects a trade-off in which the former achieves tighter spectral convergence, while the latter better preserves the physical, time-domain waveform structure. As both synthesis strategies are closed-form and computationally lightweight, the model is suitable for real-time implementation and the dynamic control of playing techniques (e.g., plucking location and, in principle, slap-type excitation), without relying on heavy, multi-gigabyte audio sample libraries.
Open AccessModeling Bass Guitar String Vibration with Frequency- and Fret-Dependent Damping for Real-Time Sound Generation
This paper presents a linear mathematical model of bass guitar string vibration with experimentally identified, frequency- and fret-dependent modal damping, aimed at high-fidelity generative sound synthesis. To identify the string damping parameters across various frets and configurations, an experimental framework was developed to benchmark four structural identification methods: half-power bandwidth, I. Yoshida’s method, Discrete Fourier Transform Interpolation, and Hilbert-transform envelope approximation. Experiments were systematically conducted on Cort C4H, Ibanez RB 630, and Yamaha bass guitars. Based on the extracted parameter space, two audio generation strategies are formulated: a spectrum-driven harmonic reconstruction method (Method 1) and a physical modeling approach utilizing spatial wave equations (Method 2). The proposed linear approximation framework effectively captures the inverse relationship between the damping factor and fret numbers specifically on the E-string, while mapping linear increases on the G and D-strings. Quantitative verification using Sobolev norm differences demonstrates good agreement between the synthesized and original signals for the spectrum-driven method (Q = 0.031–0.057) and moderate agreement for the physics-based wave equation method (Q = 0.058–0.153). This reflects a trade-off in which the former achieves tighter spectral convergence, while the latter better preserves the physical, time-domain waveform structure. As both synthesis strategies are closed-form and computationally lightweight, the model is suitable for real-time implementation and the dynamic control of playing techniques (e.g., plucking location and, in principle, slap-type excitation), without relying on heavy, multi-gigabyte audio sample libraries.
- Open Access
- 29 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (141)) , 71-82
Development a computationally efficient method to solve direct and inverse aerodynamic problems related to turbomachines
This study investigates aerodynamic processes in interblade, axial annular, and radial-axial channels in turbomachines. The task addressed relates to the need to improve the computational efficiency in solving direct and inverse aerodynamic problems when analyzing and designing flow parts of turbomachines. A computationally efficient method for solving direct and inverse aerodynamic problems has been proposed, which provides acceptable accuracy for engineering practice at significantly lower computational costs compared to conventional CFD approaches. The results include a devised single mathematical formulation based on Euler equations for a compressible fluid, written in terms of the flow function. The proposed method makes it possible to consider direct and inverse problems within a common mathematical structure. The system of equations is reduced to a single differential equation and a set of algebraic relations while the global flow problem is decomposed into a set of independent problems for individual cross-sections. The inverse problem is stated as a nonlinear optimization problem based on the mass flow rate agreement condition derived from the energy equation. The computational complexity is reduced by using the flow function and the decomposition of the computational domain. The method combines the capabilities of direct analysis and reconstruction of the flow channel geometry based on the predefined aerodynamic characteristics. Verification by experimental data and direct calculation results demonstrated good agreement between the velocity distributions and the reconstructed geometry; the maximum deviations did not exceed 0.3%. The results could be practically applied to preliminary design, parametric optimization, as well as inverse design of the flow parts in turbomachines
- 29 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (7 (141)) , 71-82
Open AccessDevelopment a computationally efficient method to solve direct and inverse aerodynamic problems related to turbomachines
This study investigates aerodynamic processes in interblade, axial annular, and radial-axial channels in turbomachines. The task addressed relates to the need to improve the computational efficiency in solving direct and inverse aerodynamic problems when analyzing and designing flow parts of turbomachines. A computationally efficient method for solving direct and inverse aerodynamic problems has been proposed, which provides acceptable accuracy for engineering practice at significantly lower computational costs compared to conventional CFD approaches. The results include a devised single mathematical formulation based on Euler equations for a compressible fluid, written in terms of the flow function. The proposed method makes it possible to consider direct and inverse problems within a common mathematical structure. The system of equations is reduced to a single differential equation and a set of algebraic relations while the global flow problem is decomposed into a set of independent problems for individual cross-sections. The inverse problem is stated as a nonlinear optimization problem based on the mass flow rate agreement condition derived from the energy equation. The computational complexity is reduced by using the flow function and the decomposition of the computational domain. The method combines the capabilities of direct analysis and reconstruction of the flow channel geometry based on the predefined aerodynamic characteristics. Verification by experimental data and direct calculation results demonstrated good agreement between the velocity distributions and the reconstructed geometry; the maximum deviations did not exceed 0.3%. The results could be practically applied to preliminary design, parametric optimization, as well as inverse design of the flow parts in turbomachines
- Open Access
- 29 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 5-16
Evaluation of Methods for Predicting Deviation Angle in Planar Turbine Cascades
This paper presents a review of methods for predicting the flow exit angle from a planar turbine cascade operating with subsonic and transonic flow regimes. An analysis of empirical correlations used to determine the deviation angle is performed, and the advantages and limitations of each approach are discussed. The accuracy of empirical correlations and the CFD approach is evaluated by comparing their predictions with experimental data obtained for the VKI turbine cascade profile under both design and off-design operating conditions. The comparison reveals a low prediction accuracy of empirical correlations for considered regimes. The largest discrepancies are observed at outlet Mach numbers below 0.6. The closest agreement with experimental data is achieved using CFD (AxCFD™). The results show good consistency both in terms of the absolute values of the deviation angle and the trend of its variation under off-design conditions. Additional CFD simulations of three planar turbine cascade configurations demonstrate a significant influence of blade geometry on the predicted deviation angle. The relationship between the kinetic energy loss coefficient and the deviation angle is also discussed. Both CFD and experimental results indicate that the minimum loss condition corresponds to the minimum deviation angle. Furthermore, a consistent trend in the variation of these two parameters is observed across different operating regimes. It is concluded that accurate prediction of the deviation angle is a complex problem requiring consideration of a wide range of geometric and operating parameters of the cascade. Further research in this area is recommended.
- 29 May 2026
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1,p. 5-16
Open AccessEvaluation of Methods for Predicting Deviation Angle in Planar Turbine Cascades
This paper presents a review of methods for predicting the flow exit angle from a planar turbine cascade operating with subsonic and transonic flow regimes. An analysis of empirical correlations used to determine the deviation angle is performed, and the advantages and limitations of each approach are discussed. The accuracy of empirical correlations and the CFD approach is evaluated by comparing their predictions with experimental data obtained for the VKI turbine cascade profile under both design and off-design operating conditions. The comparison reveals a low prediction accuracy of empirical correlations for considered regimes. The largest discrepancies are observed at outlet Mach numbers below 0.6. The closest agreement with experimental data is achieved using CFD (AxCFD™). The results show good consistency both in terms of the absolute values of the deviation angle and the trend of its variation under off-design conditions. Additional CFD simulations of three planar turbine cascade configurations demonstrate a significant influence of blade geometry on the predicted deviation angle. The relationship between the kinetic energy loss coefficient and the deviation angle is also discussed. Both CFD and experimental results indicate that the minimum loss condition corresponds to the minimum deviation angle. Furthermore, a consistent trend in the variation of these two parameters is observed across different operating regimes. It is concluded that accurate prediction of the deviation angle is a complex problem requiring consideration of a wide range of geometric and operating parameters of the cascade. Further research in this area is recommended.
- 19 May 2026
- Published by Publishing House Helvetica (Publications) in Scientific notes of Taurida National V.I. Vernadsky University. Series: Technical Sciences
- Vol. 2 (3) , 144-150
MULTI-CRITERIA OPTIMIZATION OF GAS TURBINE BLADE MATERIALS BASED ON LIFE CYCLE ASSESSMENT: INTEGRATING ECONOMIC, ENVIRONMENTAL, AND PERFORMANCE METRICS
- 19 May 2026
- Published by Publishing House Helvetica (Publications) in Scientific notes of Taurida National V.I. Vernadsky University. Series: Technical Sciences
- Vol. 2 (3) , 144-150
MULTI-CRITERIA OPTIMIZATION OF GAS TURBINE BLADE MATERIALS BASED ON LIFE CYCLE ASSESSMENT: INTEGRATING ECONOMIC, ENVIRONMENTAL, AND PERFORMANCE METRICS
- 28 December 2025
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 2,p. 32-38
Design and Operating Modes of Stop and Control Valves of High-Power Steam Turbines
The operating modes of stop and control valves of high-pressure and intermediate-pressure (low-pressure) sections of existing steam turbines of thermal and nuclear power plants are discussed in the article. Typical operating modes of the valves are defined depending on their functional purpose within the installation, the steam distribution system, the turbine type, and the method of power control. The flow pattern in angle-type valves with one side steam supply into the steam chest is discussed. It is noted that this design is typical for use in high-power steam turbine units operated in Ukraine. As a result, a classification of stop and control valves into three groups is proposed. For each group, recommendations are provided regarding the design of the valve flow-path elements, specifically the main plug and the seat, which contribute to improving their operational efficiency. In addition, to stabilize the flow, the feasibility of installing a special cylindrical shell inside the steam chest is considered, featuring an impermeable sector oriented toward the valve inlet pipe.
- 28 December 2025
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 2,p. 32-38
Design and Operating Modes of Stop and Control Valves of High-Power Steam Turbines
The operating modes of stop and control valves of high-pressure and intermediate-pressure (low-pressure) sections of existing steam turbines of thermal and nuclear power plants are discussed in the article. Typical operating modes of the valves are defined depending on their functional purpose within the installation, the steam distribution system, the turbine type, and the method of power control. The flow pattern in angle-type valves with one side steam supply into the steam chest is discussed. It is noted that this design is typical for use in high-power steam turbine units operated in Ukraine. As a result, a classification of stop and control valves into three groups is proposed. For each group, recommendations are provided regarding the design of the valve flow-path elements, specifically the main plug and the seat, which contribute to improving their operational efficiency. In addition, to stabilize the flow, the feasibility of installing a special cylindrical shell inside the steam chest is considered, featuring an impermeable sector oriented toward the valve inlet pipe.
- Open Access
- 30 April 2025
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 4,p. 12-19
Numerical Study of the Effect of a Change in the Angle of Attack on the Value of the Kinetic Energy Loss Coefficient and Flow Exit Angles for Nozzle Arrays with Rotary Diaphragms
The goal of one of the steps of this research is to develop a technique for numerical study of the flow around a nozzle array with a rotary diaphragm, for its further use for solving the problem of optimal design of the flow part of heating turbines. Due to an ample amount of numerical studies, the development of the methods is divided into several parts. The paper presents some results of numerical studies of flat flow around a nozzle array with a rotating diaphragm at angles of flow entry into the array of S-9013R profiles different from the calculated angle of attack equal to 90°. Modeling and calculation of the flow of the working fluid was performed using the Fluent software package. The construction of computational domains restricted by one interblade channel was carried out for different degrees of opening of the diaphragm of the nozzle apparatus. Grids for computational domains have been constructed. Calculations were carried out for the angles of entry into the profile grid in the range of 45º to 135º. The calculations done enabled the generation of flow patterns in the interblade channel and behind it, and the distribution of kinetic energy loss coefficients along the front of the array at various degrees of opening of the diaphragm at the entrance to the nozzle apparatus. Based on the results of the work done, the following conclusions can be drawn: a change in the angle of attack affects the distribution of static pressure along the profile only in its front part, and does not affect the distribution in the output part; a change in the angles of attack does not affect the exit angles from the nozzle array of S-9013R profiles; a decrease in the pressure difference across the nozzle array results in a change in the exit angles from the nozzle array at an opening degree of the rotary diaphragm of π > 0.5.
- 30 April 2025
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 4,p. 12-19
Open AccessNumerical Study of the Effect of a Change in the Angle of Attack on the Value of the Kinetic Energy Loss Coefficient and Flow Exit Angles for Nozzle Arrays with Rotary Diaphragms
The goal of one of the steps of this research is to develop a technique for numerical study of the flow around a nozzle array with a rotary diaphragm, for its further use for solving the problem of optimal design of the flow part of heating turbines. Due to an ample amount of numerical studies, the development of the methods is divided into several parts. The paper presents some results of numerical studies of flat flow around a nozzle array with a rotating diaphragm at angles of flow entry into the array of S-9013R profiles different from the calculated angle of attack equal to 90°. Modeling and calculation of the flow of the working fluid was performed using the Fluent software package. The construction of computational domains restricted by one interblade channel was carried out for different degrees of opening of the diaphragm of the nozzle apparatus. Grids for computational domains have been constructed. Calculations were carried out for the angles of entry into the profile grid in the range of 45º to 135º. The calculations done enabled the generation of flow patterns in the interblade channel and behind it, and the distribution of kinetic energy loss coefficients along the front of the array at various degrees of opening of the diaphragm at the entrance to the nozzle apparatus. Based on the results of the work done, the following conclusions can be drawn: a change in the angle of attack affects the distribution of static pressure along the profile only in its front part, and does not affect the distribution in the output part; a change in the angles of attack does not affect the exit angles from the nozzle array of S-9013R profiles; a decrease in the pressure difference across the nozzle array results in a change in the exit angles from the nozzle array at an opening degree of the rotary diaphragm of π > 0.5.
- 16 July 2024
- Published by Springer Nature
- p. 22-33
The Inlet Average Absolute Flow Angle Effect on Mixed Inflow Turbine Rotor Performances
- 16 July 2024
- Published by Springer Nature
- p. 22-33
The Inlet Average Absolute Flow Angle Effect on Mixed Inflow Turbine Rotor Performances
- Open Access
- 28 December 2022
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 32-39
Information and Mathematical Models of the Flow Part in the Problems of Optimal Design of a Turboblock
The issues of improving the structural-topological formation of the information model of the flow path of a steam turbine with the aim of using it in the problems of optimal design of turbine blocks are considered. A new hierarchical level "Compartment" has been added, which made it possible to link in a single information space the parameters of the frequency converter and the rest of the equipment of the turbine unit and made it possible to set and solve the problems of optimal design of turbine blocks. An improved one-dimensional model of the processes in the frequency converter, which allows simulating the course of processes in the frequency converter of a turbine from compartment to compartment (sub-section modeling of processes in the frequency converter with given steam parameters between the compartments). The improved mathematical model of the processes in the frequency converter is coordinated with the improved information model of the frequency converter and is one of the components of the optimal design subsystem of the “Turboagregat” CAD system. The performed test comparative calculations of the FC of steam turbine cylinders were carried out using algorithms created on the basis of two mathematical models: the original and the improved one. Good agreement was confirmed. Insignificant differences in thermogasdynamic parameters in the cross-sections between the rims of the inverter, obtained according to the original and improved models, are noted. Small deviations in the results are mainly caused by the need to use in the improved model the formulation of the problem with the given steam parameters in front of each compartment and the value of the mass flow rate to the head of each compartment. The fulfillment of the boundary conditions was ensured by a corresponding change in the effective angle of the nozzle grate of the first stage of each compartment.
- 28 December 2022
- Published by National Technical University Kharkiv Polytechnic Institute in NTU "KhPI" Bulletin: Power and heat engineering processes and equipment
- No. 1-2,p. 32-39
Open AccessInformation and Mathematical Models of the Flow Part in the Problems of Optimal Design of a Turboblock
The issues of improving the structural-topological formation of the information model of the flow path of a steam turbine with the aim of using it in the problems of optimal design of turbine blocks are considered. A new hierarchical level "Compartment" has been added, which made it possible to link in a single information space the parameters of the frequency converter and the rest of the equipment of the turbine unit and made it possible to set and solve the problems of optimal design of turbine blocks. An improved one-dimensional model of the processes in the frequency converter, which allows simulating the course of processes in the frequency converter of a turbine from compartment to compartment (sub-section modeling of processes in the frequency converter with given steam parameters between the compartments). The improved mathematical model of the processes in the frequency converter is coordinated with the improved information model of the frequency converter and is one of the components of the optimal design subsystem of the “Turboagregat” CAD system. The performed test comparative calculations of the FC of steam turbine cylinders were carried out using algorithms created on the basis of two mathematical models: the original and the improved one. Good agreement was confirmed. Insignificant differences in thermogasdynamic parameters in the cross-sections between the rims of the inverter, obtained according to the original and improved models, are noted. Small deviations in the results are mainly caused by the need to use in the improved model the formulation of the problem with the given steam parameters in front of each compartment and the value of the mass flow rate to the head of each compartment. The fulfillment of the boundary conditions was ensured by a corresponding change in the effective angle of the nozzle grate of the first stage of each compartment.
- 22 August 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 19-25
Процес дроселювання в соплових апаратах з поворотними діафрагмами
In the process of developing a method for numerically investigating a plane flow around a nozzle array with a rotary diaphragm, calculations were performed for various degrees of opening of the rotary diaphragm δ and pressure drops π on the array. The article presents some results of a numerical study of the flow in the nozzle channel at the degree of opening of the rotary diaphragm δ = (1…0.15). Modeling and calculations of the flow of the working fluid were performed using the Fluent software package. The construction of computational areas, limited by one inter-blade channel, for a different degree of opening of the diaphragm of the nozzle apparatus has been carried out. The grids for the computational domains were constructed. Calculations were carried out for δ = (1…0.15) and for various degrees of pressure drop across the grate. Because of the performed calculations, flow patterns in the interblade channel and behind it, and the distribution of kinetic energy loss coefficients along the grating front at various degrees of aperture opening at the nozzle inlet, were obtained. Based on the results of the work carried out, the following conclusions can be drawn: the operation of a nozzle array with a rotary diaphragm at different degrees of opening of the rotary diaphragm δ and pressure drops π on the grate can be divided in the range of opening steps δ = (1…0.77) as operation in the nozzle mode, and in the range δ = (0.77…0.15) as in throttle mode; when the angle of attack changes, the values of the kinetic energy loss coefficients increase significantly (up to 25 %) only for π = 0.7 and δ = 1; at π = 0.3 and δ = 1, the coefficient increases slightly (up to 0.5 %); at π = 0.7; 0.3 and δ = 0.3, the coefficient increases to 5 %, while the coefficient ζі changes less relative to the coefficient ζ90 at the calculated angle of attack α0 = 90 grids). The results obtained in this work will be used to develop a technique for numerically investigating the spatial flow around nozzle arrays with rotary diaphragms.
- 22 August 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 19-25
Процес дроселювання в соплових апаратах з поворотними діафрагмами
In the process of developing a method for numerically investigating a plane flow around a nozzle array with a rotary diaphragm, calculations were performed for various degrees of opening of the rotary diaphragm δ and pressure drops π on the array. The article presents some results of a numerical study of the flow in the nozzle channel at the degree of opening of the rotary diaphragm δ = (1…0.15). Modeling and calculations of the flow of the working fluid were performed using the Fluent software package. The construction of computational areas, limited by one inter-blade channel, for a different degree of opening of the diaphragm of the nozzle apparatus has been carried out. The grids for the computational domains were constructed. Calculations were carried out for δ = (1…0.15) and for various degrees of pressure drop across the grate. Because of the performed calculations, flow patterns in the interblade channel and behind it, and the distribution of kinetic energy loss coefficients along the grating front at various degrees of aperture opening at the nozzle inlet, were obtained. Based on the results of the work carried out, the following conclusions can be drawn: the operation of a nozzle array with a rotary diaphragm at different degrees of opening of the rotary diaphragm δ and pressure drops π on the grate can be divided in the range of opening steps δ = (1…0.77) as operation in the nozzle mode, and in the range δ = (0.77…0.15) as in throttle mode; when the angle of attack changes, the values of the kinetic energy loss coefficients increase significantly (up to 25 %) only for π = 0.7 and δ = 1; at π = 0.3 and δ = 1, the coefficient increases slightly (up to 0.5 %); at π = 0.7; 0.3 and δ = 0.3, the coefficient increases to 5 %, while the coefficient ζі changes less relative to the coefficient ζ90 at the calculated angle of attack α0 = 90 grids). The results obtained in this work will be used to develop a technique for numerically investigating the spatial flow around nozzle arrays with rotary diaphragms.
- 25 May 2022
- Published by Springer Nature
- p. 66-78
Supersonic Flow in the Blade Channel of the Nozzle with a Rotary Diaphragm at Small Degrees of Opening
- 25 May 2022
- Published by Springer Nature
- p. 66-78
Supersonic Flow in the Blade Channel of the Nozzle with a Rotary Diaphragm at Small Degrees of Opening