Stanislav Popelka
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Stanislav Popelka has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Pavel Hazdra
Department of Microelectronics Faculty of Electrical Engineering Czech Technical University in Prague Technická 2 CZ-166 27 Prague 6 Czech Republic
17 shared publications Rupendra Kumar Sharma
Czech Technical University in Prague
5 shared publicationsVít Záhlava
Czech Technical University in Prague
2 shared publications- Adolf Schoner
Ascatron AB, Kista, Sweden
1 shared publication Adolf Schöner
Ascatron AB
1 shared publicationAndrei Mihaila
ABB Switzerland Ltd
1 shared publication
Latest Publications
- 20 May 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (23)
Radiation Defects and Carrier Lifetime in 4H‐SiC Bipolar Devices
The effect of radiation damage on the minority carrier lifetime in the 4 H‐SiC epilayers forming the n‐base of the power p–i–n diodes is presented. Irradiation with fast neutrons and MeV protons is used for uniform and local lifetime reduction. Deep‐level transient spectroscopy in combination with open‐circuit voltage decay measurement shows that the carrier lifetime is reduced by increased carrier recombination on Z1/Z2, EH3, and possibly RD4 levels. The lifetime degrades swiftly and the ON‐state carrier modulation capability of high‐voltage devices can be easily lost already at very low fluences. The results further show that the proton irradiation provides an excellent tool for local lifetime tailoring. The carrier lifetime can be easily set by proton fluence and localized by proton energy. The proper local lifetime reduction speeds up diode recovery without an undesirable increase in the forward voltage drop. However, attention must be taken to properly locate the damage maximum so as not to increase device leakage.
- 20 May 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (23)
Radiation Defects and Carrier Lifetime in 4H‐SiC Bipolar Devices
The effect of radiation damage on the minority carrier lifetime in the 4 H‐SiC epilayers forming the n‐base of the power p–i–n diodes is presented. Irradiation with fast neutrons and MeV protons is used for uniform and local lifetime reduction. Deep‐level transient spectroscopy in combination with open‐circuit voltage decay measurement shows that the carrier lifetime is reduced by increased carrier recombination on Z1/Z2, EH3, and possibly RD4 levels. The lifetime degrades swiftly and the ON‐state carrier modulation capability of high‐voltage devices can be easily lost already at very low fluences. The results further show that the proton irradiation provides an excellent tool for local lifetime tailoring. The carrier lifetime can be easily set by proton fluence and localized by proton energy. The proper local lifetime reduction speeds up diode recovery without an undesirable increase in the forward voltage drop. However, attention must be taken to properly locate the damage maximum so as not to increase device leakage.
- 19 July 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 963, 718-721
Radiation Effects on 1.7kV Class 4H-SiC Power Devices: Development of Compact Simulation Models
Compact simulation models of two key silicon carbide power components, the Junction Barrier Schottky diode and the power MOSFET, which are taking into account the effect of irradiation by highenergy electrons, were developed. Two 1.7 kV class devices: the 14 A JBS diode C3D10170H and the 5 A SiC power MOSFETs C2M1000170D produced by Wolfspeed were irradiated by 4.5 MeV electrons in the dose range up to 2000 kGy. Electrical characteristics were measured prior to and after irradiation. Radiation defects were studied by deep level transient spectroscopy and the effect of irradiation on device characteristics was established. SPICE models taking into account the irradiation fluence were proposed and calibrated using the parameters extracted from experiment. Simulated characteristics show a very good agreement with reality.
- 19 July 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 963, 718-721
Radiation Effects on 1.7kV Class 4H-SiC Power Devices: Development of Compact Simulation Models
Compact simulation models of two key silicon carbide power components, the Junction Barrier Schottky diode and the power MOSFET, which are taking into account the effect of irradiation by highenergy electrons, were developed. Two 1.7 kV class devices: the 14 A JBS diode C3D10170H and the 5 A SiC power MOSFETs C2M1000170D produced by Wolfspeed were irradiated by 4.5 MeV electrons in the dose range up to 2000 kGy. Electrical characteristics were measured prior to and after irradiation. Radiation defects were studied by deep level transient spectroscopy and the effect of irradiation on device characteristics was established. SPICE models taking into account the irradiation fluence were proposed and calibrated using the parameters extracted from experiment. Simulated characteristics show a very good agreement with reality.
- 30 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4483-4489
Optimization of SiC Power p-i-n Diode Parameters by Proton Irradiation
Local lifetime reduction by proton irradiation was used to optimize the static and dynamic parameters of a 10 kV SiC p-i-n diode. Carrier lifetime was reduced locally at the anode side by irradiation with 800 keV protons at fluences up to 1 × 10 11 cm -2 . Results show that proton irradiation followed by annealing at 370 °C can be used for local and controllable reduction of carrier lifetime in SiC devices. The dominant recombination center is the Z 1/2 defect, whose distribution can be set by irradiation energy and fluence. Proton irradiation substantially improves diode turn-off while its effect on the forward voltage drop and leakage is not so harmful. Comparison of the technology curve for the unirradiated and proton irradiated p-i-n diode then clearly shows that proton irradiation provides a superior tradeoff between the static and dynamic losses.
- 30 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4483-4489
Optimization of SiC Power p-i-n Diode Parameters by Proton Irradiation
Local lifetime reduction by proton irradiation was used to optimize the static and dynamic parameters of a 10 kV SiC p-i-n diode. Carrier lifetime was reduced locally at the anode side by irradiation with 800 keV protons at fluences up to 1 × 10 11 cm -2 . Results show that proton irradiation followed by annealing at 370 °C can be used for local and controllable reduction of carrier lifetime in SiC devices. The dominant recombination center is the Z 1/2 defect, whose distribution can be set by irradiation energy and fluence. Proton irradiation substantially improves diode turn-off while its effect on the forward voltage drop and leakage is not so harmful. Comparison of the technology curve for the unirradiated and proton irradiated p-i-n diode then clearly shows that proton irradiation provides a superior tradeoff between the static and dynamic losses.
- 5 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 924, 436-439
Local Lifetime Control in 4H-SiC by Proton Irradiation
The effect of local lifetime control by proton irradiation on the OCVD response of a 10 kV SiC PiN diode was investigated. Carrier lifetime was reduced locally by irradiation with 800 keV protons at fluences up to 1x1011 cm-2. Radiation defects were characterized by DLTS and C-V profiling; excess carrier dynamics were measured by the OCVD and analyzed using the calibrated device simulator ATLAS from Silvaco, Inc. Results show that proton implantation followed by low temperature annealing can be used for controllable local lifetime reduction in SiC devices. The dominant recombination centre is the Z1/2 defect, whose distribution can be set by irradiation energy and fluence. The local lifetime reduction, which improves diode recovery, can be monitored by OCVD response and simulated using the SRH model accounting for the Z1/2 defect.
- 5 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 924, 436-439
Local Lifetime Control in 4H-SiC by Proton Irradiation
The effect of local lifetime control by proton irradiation on the OCVD response of a 10 kV SiC PiN diode was investigated. Carrier lifetime was reduced locally by irradiation with 800 keV protons at fluences up to 1x1011 cm-2. Radiation defects were characterized by DLTS and C-V profiling; excess carrier dynamics were measured by the OCVD and analyzed using the calibrated device simulator ATLAS from Silvaco, Inc. Results show that proton implantation followed by low temperature annealing can be used for controllable local lifetime reduction in SiC devices. The dominant recombination centre is the Z1/2 defect, whose distribution can be set by irradiation energy and fluence. The local lifetime reduction, which improves diode recovery, can be monitored by OCVD response and simulated using the SRH model accounting for the Z1/2 defect.
- 1 July 2017
- Published by Elsevier in Microelectronics Reliability
- Vol. 74, 58-66
Operation of 4H-SiC high voltage normally-OFF V-JFET in radiation hard conditions: Simulations and experiment
- 1 July 2017
- Published by Elsevier in Microelectronics Reliability
- Vol. 74, 58-66
Operation of 4H-SiC high voltage normally-OFF V-JFET in radiation hard conditions: Simulations and experiment
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 463-466
Lifetime Control in SiC PiN Diodes Using Radiation Defects
Application of radiation defects for lifetime control in contemporary SiC PiN diodes was investigated using the calibrated device simulator ATLAS from Silvaco, Inc. Recombination models accounting for the effect of deep levels introduced by the irradiation were set according to experimental results obtained by C-V and DLTS measurements performed on low-doped n-type SiC epilayers irradiated with 4.5 MeV electrons and 670 keV protons. Global (4.5 MeV electron irradiation) and local (700 keV proton irradiation) lifetime reduction was then applied on the 2A/10kV SiC PiN diode and the ON-state and reverse recovery characteristics were simulated and compared. Results show that the proton irradiation can substantially improve the trade‑off between the diode ON‑state and turn‑OFF losses. Compared to the electron irradiation, the local lifetime killing by protons allows achieving better trade-off and softer recovery curves.
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 463-466
Lifetime Control in SiC PiN Diodes Using Radiation Defects
Application of radiation defects for lifetime control in contemporary SiC PiN diodes was investigated using the calibrated device simulator ATLAS from Silvaco, Inc. Recombination models accounting for the effect of deep levels introduced by the irradiation were set according to experimental results obtained by C-V and DLTS measurements performed on low-doped n-type SiC epilayers irradiated with 4.5 MeV electrons and 670 keV protons. Global (4.5 MeV electron irradiation) and local (700 keV proton irradiation) lifetime reduction was then applied on the 2A/10kV SiC PiN diode and the ON-state and reverse recovery characteristics were simulated and compared. Results show that the proton irradiation can substantially improve the trade‑off between the diode ON‑state and turn‑OFF losses. Compared to the electron irradiation, the local lifetime killing by protons allows achieving better trade-off and softer recovery curves.
- 25 October 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (4)
Radiation resistance of wide-bandgap semiconductor power transistors
- 25 October 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (4)
Radiation resistance of wide-bandgap semiconductor power transistors
- 24 May 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 858, 782-785
Optimization of 1700V 4H-SiC JBS Diode Parameters
The in-depth design optimization of the active layer of the 1700V class 4H-SiC JBS/MPS diode structure is discussed. The important design parameters such as junction depth (d), width (w) of p+ areas, and spacing (s) between them were optimized for the best possible trade-off between the unipolar ON-state voltage drop, the OFF-state breakdown voltage, and the bipolar surge current capability. The optimization was performed using a state-of-the-art simulator using device models calibrated on a commercially available JBS rectifier. The results show that the spacing s between the p+ regions is the most decisive parameter which has to be properly designed according to the required voltage class. For the 1700 V voltage class, s should be between 2 to 4 μm and the s/w ratio should be kept low. The depth d of the p+ pattern has a pronounced impact on the ignition of bipolar action such that with decreasing d the surge current capability decreases significantly.
- 24 May 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 858, 782-785
Optimization of 1700V 4H-SiC JBS Diode Parameters
The in-depth design optimization of the active layer of the 1700V class 4H-SiC JBS/MPS diode structure is discussed. The important design parameters such as junction depth (d), width (w) of p+ areas, and spacing (s) between them were optimized for the best possible trade-off between the unipolar ON-state voltage drop, the OFF-state breakdown voltage, and the bipolar surge current capability. The optimization was performed using a state-of-the-art simulator using device models calibrated on a commercially available JBS rectifier. The results show that the spacing s between the p+ regions is the most decisive parameter which has to be properly designed according to the required voltage class. For the 1700 V voltage class, s should be between 2 to 4 μm and the s/w ratio should be kept low. The depth d of the p+ pattern has a pronounced impact on the ignition of bipolar action such that with decreasing d the surge current capability decreases significantly.
- 24 May 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 858, 856-859
Effect of Electron Irradiation on 1700V 4H-SiC MOSFET Characteristics
The effect of 4.5 MeV electron irradiation on static characteristics of commercially available 5 A/1700 V SiC power MOSFETs is investigated. Results show that in the low dose range (up to 20 kGy) the threshold voltage decreases rapidly with irradiation dose but devices keep full functionality. This effect is caused by embedding of the positive charge into the gate oxide. When electron dose reaches 200 kGy, the threshold voltage moves back close to its original value, however, the ON‑state resistivity increases and transconductance is lowered. This is caused by introduction of deep acceptor centers into the low doped drift region of MOSFET. This effect can be considered as a cause of the final failure of the device (the lost of the ON-state capability).
- 24 May 2016
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 858, 856-859
Effect of Electron Irradiation on 1700V 4H-SiC MOSFET Characteristics
The effect of 4.5 MeV electron irradiation on static characteristics of commercially available 5 A/1700 V SiC power MOSFETs is investigated. Results show that in the low dose range (up to 20 kGy) the threshold voltage decreases rapidly with irradiation dose but devices keep full functionality. This effect is caused by embedding of the positive charge into the gate oxide. When electron dose reaches 200 kGy, the threshold voltage moves back close to its original value, however, the ON‑state resistivity increases and transconductance is lowered. This is caused by introduction of deep acceptor centers into the low doped drift region of MOSFET. This effect can be considered as a cause of the final failure of the device (the lost of the ON-state capability).
- 23 October 2015
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 242, 421-426
Radiation Damage in 4H-SiC and its Effect on Power Device Characteristics
The effect of neutron, electron and ion irradiation on electrical characteristics of unipolar 1700V SiC power devices (JBS diodes, JFETs and MESFETs) was investigated. DLTS investigation showed that above mentioned projectiles introduce similar deep acceptor levels (electron traps) in the SiC bandgap which compensate nitrogen shallow donors and cause majority carrier (electron) removal. The key degradation effect occurring in irradiated devices is the increase of the ON-state resistance which is caused by compensation of the low doped n-type epilayer and simultaneous lowering of electron mobility. In the case of SiC power switches (JFET, MOSFET), these effects are accompanied by the shift of the threshold voltage. Radiation defects introduced in SiC power devices is unstable and some defects anneal out already at operation temperatures (below 175°C). However, this does not have significant effect on device characteristics.
- 23 October 2015
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 242, 421-426
Radiation Damage in 4H-SiC and its Effect on Power Device Characteristics
The effect of neutron, electron and ion irradiation on electrical characteristics of unipolar 1700V SiC power devices (JBS diodes, JFETs and MESFETs) was investigated. DLTS investigation showed that above mentioned projectiles introduce similar deep acceptor levels (electron traps) in the SiC bandgap which compensate nitrogen shallow donors and cause majority carrier (electron) removal. The key degradation effect occurring in irradiated devices is the increase of the ON-state resistance which is caused by compensation of the low doped n-type epilayer and simultaneous lowering of electron mobility. In the case of SiC power switches (JFET, MOSFET), these effects are accompanied by the shift of the threshold voltage. Radiation defects introduced in SiC power devices is unstable and some defects anneal out already at operation temperatures (below 175°C). However, this does not have significant effect on device characteristics.