Pavel Hazdra
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Pavel Hazdra has a total of 101 co-authors. Here are the top co-authors by number of shared publications:
- Stanislav Popelka
Czech Technical University in Prague
17 shared publications - Eduard Hulicius
Institute of Physics, CAS, v.v.i., 162 00, Cukrovarnická 10, Prague 6, Czech Republic
16 shared publications J. Vobecký
12 shared publications- Jiri Pangrac
Institute of Physics of the ASCR, v.v.i. (Czech Republic)
12 shared publications J. Oswald
10 shared publicationsJ. Vobecky
The Department of Microelectronics, Czech Technical University in Prague, Technicka 2, Prague 6, Czech Republic
10 shared publications
Latest Publications
- 27 October 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (23)
Pseudo‐Vertical Schottky Diode with Ruthenium Contacts on (113) Boron‐Doped Homoepitaxial Diamond Layers
Electrical properties of pseudo‐vertical Schottky barrier diodes (pVSBDs) prepared on (113)–oriented boron‐doped diamond (BDD) layers using ruthenium (Ru) for both the ohmic and Schottky contacts are investigated. First, Ru ohmic contacts are evaporated on homoepitaxial BDD layers with different resistivity, and their specific contact resistance is measured using circular transfer length method structures after annealing at various temperatures up to 750 °C. Then, pVSBD structures are fabricated on the boron‐doped bilayer consisting of a lower, heavily boron‐doped layer ensuring an ohmic contact and an upper, lightly doped layer providing a rectifying Schottky contact. After necessary mesa etching, both contacts are formed by the Ru evaporation. The results show that Ru forms a stable ohmic contact with very low contact resistance (10−5–10−6 Ω cm2) when deposited on BDD layers with metallic conductivity. It also provides an acceptable Schottky contact on low‐doped (113) homoepitaxial BDD. Both contacts, which are made simultaneously, realize pVSBDs with low on‐state resistance and low forward voltage drop. However, the lower barrier of the ruthenium contacts results in higher leakage. Ru pVSBDs thus show a lower rectification ratio, higher leakage, and a worse ideality factor compared to analogical pVSBDs using molybdenum contacts.
- 27 October 2023
- Published by Wiley in Physica Status Solidi (a)
- Vol. 220 (23)
Pseudo‐Vertical Schottky Diode with Ruthenium Contacts on (113) Boron‐Doped Homoepitaxial Diamond Layers
Electrical properties of pseudo‐vertical Schottky barrier diodes (pVSBDs) prepared on (113)–oriented boron‐doped diamond (BDD) layers using ruthenium (Ru) for both the ohmic and Schottky contacts are investigated. First, Ru ohmic contacts are evaporated on homoepitaxial BDD layers with different resistivity, and their specific contact resistance is measured using circular transfer length method structures after annealing at various temperatures up to 750 °C. Then, pVSBD structures are fabricated on the boron‐doped bilayer consisting of a lower, heavily boron‐doped layer ensuring an ohmic contact and an upper, lightly doped layer providing a rectifying Schottky contact. After necessary mesa etching, both contacts are formed by the Ru evaporation. The results show that Ru forms a stable ohmic contact with very low contact resistance (10−5–10−6 Ω cm2) when deposited on BDD layers with metallic conductivity. It also provides an acceptable Schottky contact on low‐doped (113) homoepitaxial BDD. Both contacts, which are made simultaneously, realize pVSBDs with low on‐state resistance and low forward voltage drop. However, the lower barrier of the ruthenium contacts results in higher leakage. Ru pVSBDs thus show a lower rectification ratio, higher leakage, and a worse ideality factor compared to analogical pVSBDs using molybdenum contacts.
- 20 May 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (23)
Radiation Defects and Carrier Lifetime in 4H‐SiC Bipolar Devices
The effect of radiation damage on the minority carrier lifetime in the 4 H‐SiC epilayers forming the n‐base of the power p–i–n diodes is presented. Irradiation with fast neutrons and MeV protons is used for uniform and local lifetime reduction. Deep‐level transient spectroscopy in combination with open‐circuit voltage decay measurement shows that the carrier lifetime is reduced by increased carrier recombination on Z1/Z2, EH3, and possibly RD4 levels. The lifetime degrades swiftly and the ON‐state carrier modulation capability of high‐voltage devices can be easily lost already at very low fluences. The results further show that the proton irradiation provides an excellent tool for local lifetime tailoring. The carrier lifetime can be easily set by proton fluence and localized by proton energy. The proper local lifetime reduction speeds up diode recovery without an undesirable increase in the forward voltage drop. However, attention must be taken to properly locate the damage maximum so as not to increase device leakage.
- 20 May 2021
- Published by Wiley in Physica Status Solidi (a)
- Vol. 218 (23)
Radiation Defects and Carrier Lifetime in 4H‐SiC Bipolar Devices
The effect of radiation damage on the minority carrier lifetime in the 4 H‐SiC epilayers forming the n‐base of the power p–i–n diodes is presented. Irradiation with fast neutrons and MeV protons is used for uniform and local lifetime reduction. Deep‐level transient spectroscopy in combination with open‐circuit voltage decay measurement shows that the carrier lifetime is reduced by increased carrier recombination on Z1/Z2, EH3, and possibly RD4 levels. The lifetime degrades swiftly and the ON‐state carrier modulation capability of high‐voltage devices can be easily lost already at very low fluences. The results further show that the proton irradiation provides an excellent tool for local lifetime tailoring. The carrier lifetime can be easily set by proton fluence and localized by proton energy. The proper local lifetime reduction speeds up diode recovery without an undesirable increase in the forward voltage drop. However, attention must be taken to properly locate the damage maximum so as not to increase device leakage.
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (1) , 202-207
Radiation Resistance of High-Voltage Silicon and 4H-SiC Power p-i-n Diodes
The different effect of displacement damage produced by neutron irradiation on the static characteristics of 4.5-kV silicon and 4H silicon carbide (SiC) p-i-n power diodes is explained using deep level transient spectroscopy (DLTS), C-V profiling, and open-circuit voltage decay (OCVD) measurements. The number of introduced defects in SiC is higher, also the degradation of carrier lifetime and carrier removal proceeds more swiftly in SiC than those in silicon. However, smaller dimensions and a higher doping level of the n-base of the SiC diode compensate for these negative effects. As a result, the SiC p-i-n diode exhibits substantially higher resistance to neutron irradiation at higher fluences when the diode loses its on-state carrier modulation capability. SiC also shows a negligible effect of irradiation on leakage current due to the wider bandgap. One may assume a better reliability of SiC bipolar devices over the silicon in a high neutron radiation environment.
- 1 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 68 (1) , 202-207
Radiation Resistance of High-Voltage Silicon and 4H-SiC Power p-i-n Diodes
The different effect of displacement damage produced by neutron irradiation on the static characteristics of 4.5-kV silicon and 4H silicon carbide (SiC) p-i-n power diodes is explained using deep level transient spectroscopy (DLTS), C-V profiling, and open-circuit voltage decay (OCVD) measurements. The number of introduced defects in SiC is higher, also the degradation of carrier lifetime and carrier removal proceeds more swiftly in SiC than those in silicon. However, smaller dimensions and a higher doping level of the n-base of the SiC diode compensate for these negative effects. As a result, the SiC p-i-n diode exhibits substantially higher resistance to neutron irradiation at higher fluences when the diode loses its on-state carrier modulation capability. SiC also shows a negligible effect of irradiation on leakage current due to the wider bandgap. One may assume a better reliability of SiC bipolar devices over the silicon in a high neutron radiation environment.
- Open Access
- 29 October 2019
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 12 (15) , 3910-3918
Displacement damage and total ionisation dose effects on 4H‐SiC power devices
A comprehensive study of displacement damage and total ionisation dose effects on 4H‐silicon carbide power devices is presented. Power diodes and transistors produced by different manufacturers were irradiated by high‐energy particles (protons, alphas, electrons and neutrons). The influence of radiation on device characteristics was determined, the introduced radiation defects were identified, and the main degradation mechanisms were established. Results show that radiation leads to the creation of acceptor traps in the lightly doped drift regions of irradiated devices. Devices then degrade due to the removal of the carriers and the decrease in carrier mobility and lifetime. For unipolar devices, the gradual increase of the forward voltage is typical while the blocking characteristics remain nearly unchanged. In bipolar devices, high introduction rates of defects cause a sharp reduction of carrier lifetime. This results in shorter carrier diffusion lengths and subsequent loss of conductivity modulation leading to a sharp increase of the forward voltage drop. The irradiation also shifts the threshold voltage of power switches. That is critical, namely for metal–oxide–semiconductor field‐effect transistors. According to the authors’ study, the junction barrier Schottky diode and junction field‐effect transistor (JFET) can be considered the most radiation‐resistant SiC power devices.
- 29 October 2019
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 12 (15) , 3910-3918
Open AccessDisplacement damage and total ionisation dose effects on 4H‐SiC power devices
A comprehensive study of displacement damage and total ionisation dose effects on 4H‐silicon carbide power devices is presented. Power diodes and transistors produced by different manufacturers were irradiated by high‐energy particles (protons, alphas, electrons and neutrons). The influence of radiation on device characteristics was determined, the introduced radiation defects were identified, and the main degradation mechanisms were established. Results show that radiation leads to the creation of acceptor traps in the lightly doped drift regions of irradiated devices. Devices then degrade due to the removal of the carriers and the decrease in carrier mobility and lifetime. For unipolar devices, the gradual increase of the forward voltage is typical while the blocking characteristics remain nearly unchanged. In bipolar devices, high introduction rates of defects cause a sharp reduction of carrier lifetime. This results in shorter carrier diffusion lengths and subsequent loss of conductivity modulation leading to a sharp increase of the forward voltage drop. The irradiation also shifts the threshold voltage of power switches. That is critical, namely for metal–oxide–semiconductor field‐effect transistors. According to the authors’ study, the junction barrier Schottky diode and junction field‐effect transistor (JFET) can be considered the most radiation‐resistant SiC power devices.
- 2 July 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
Radiation Defects Created in n‐Type 4H‐SiC by Electron Irradiation in the Energy Range of 1–10 MeV
Radiation damage produced in 4H‐SiC n‐epilayers by electrons of different energies is presented. Junction barrier Schottky power SiC diodes are irradiated with 1.05, 2.1, 5, and 10 MeV electrons with doses up to 600 kGy. Radiation defects are characterized by capacitance deep‐level transient spectroscopy and capacitance‐to‐voltage (C–V) measurement. Results, which are compared with previous data obtained on 4.5 MeV electrons, show that the damage structure is very similar for all irradiation energies. Dominating is the generation of simple, thermally unstable defects evidenced by the presence of acceptor levels located at 0.25, 0.38, 0.60, and 0.72 eV below the 4H‐SiC conduction band edge. With increasing energy of electrons, the number of simple defects saturates, and the production of more complex, cluster‐related defects grow. Majority of introduced defects are acceptor centers, which compensate n‐type (nitrogen) doping of the epilayer. The carrier removal rate increases with electron energy and follows well the classical nonionization energy loss (NIEL) scaling for electrons in silicon. The stability of introduced defects and their effect on carrier lifetime reduction are discussed, as well.
- 2 July 2019
- Published by Wiley in Physica Status Solidi (a)
- Vol. 216 (17)
Radiation Defects Created in n‐Type 4H‐SiC by Electron Irradiation in the Energy Range of 1–10 MeV
Radiation damage produced in 4H‐SiC n‐epilayers by electrons of different energies is presented. Junction barrier Schottky power SiC diodes are irradiated with 1.05, 2.1, 5, and 10 MeV electrons with doses up to 600 kGy. Radiation defects are characterized by capacitance deep‐level transient spectroscopy and capacitance‐to‐voltage (C–V) measurement. Results, which are compared with previous data obtained on 4.5 MeV electrons, show that the damage structure is very similar for all irradiation energies. Dominating is the generation of simple, thermally unstable defects evidenced by the presence of acceptor levels located at 0.25, 0.38, 0.60, and 0.72 eV below the 4H‐SiC conduction band edge. With increasing energy of electrons, the number of simple defects saturates, and the production of more complex, cluster‐related defects grow. Majority of introduced defects are acceptor centers, which compensate n‐type (nitrogen) doping of the epilayer. The carrier removal rate increases with electron energy and follows well the classical nonionization energy loss (NIEL) scaling for electrons in silicon. The stability of introduced defects and their effect on carrier lifetime reduction are discussed, as well.
- 30 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4483-4489
Optimization of SiC Power p-i-n Diode Parameters by Proton Irradiation
Local lifetime reduction by proton irradiation was used to optimize the static and dynamic parameters of a 10 kV SiC p-i-n diode. Carrier lifetime was reduced locally at the anode side by irradiation with 800 keV protons at fluences up to 1 × 10 11 cm -2 . Results show that proton irradiation followed by annealing at 370 °C can be used for local and controllable reduction of carrier lifetime in SiC devices. The dominant recombination center is the Z 1/2 defect, whose distribution can be set by irradiation energy and fluence. Proton irradiation substantially improves diode turn-off while its effect on the forward voltage drop and leakage is not so harmful. Comparison of the technology curve for the unirradiated and proton irradiated p-i-n diode then clearly shows that proton irradiation provides a superior tradeoff between the static and dynamic losses.
- 30 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 65 (10) , 4483-4489
Optimization of SiC Power p-i-n Diode Parameters by Proton Irradiation
Local lifetime reduction by proton irradiation was used to optimize the static and dynamic parameters of a 10 kV SiC p-i-n diode. Carrier lifetime was reduced locally at the anode side by irradiation with 800 keV protons at fluences up to 1 × 10 11 cm -2 . Results show that proton irradiation followed by annealing at 370 °C can be used for local and controllable reduction of carrier lifetime in SiC devices. The dominant recombination center is the Z 1/2 defect, whose distribution can be set by irradiation energy and fluence. Proton irradiation substantially improves diode turn-off while its effect on the forward voltage drop and leakage is not so harmful. Comparison of the technology curve for the unirradiated and proton irradiated p-i-n diode then clearly shows that proton irradiation provides a superior tradeoff between the static and dynamic losses.
- 5 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 924, 436-439
Local Lifetime Control in 4H-SiC by Proton Irradiation
The effect of local lifetime control by proton irradiation on the OCVD response of a 10 kV SiC PiN diode was investigated. Carrier lifetime was reduced locally by irradiation with 800 keV protons at fluences up to 1x1011 cm-2. Radiation defects were characterized by DLTS and C-V profiling; excess carrier dynamics were measured by the OCVD and analyzed using the calibrated device simulator ATLAS from Silvaco, Inc. Results show that proton implantation followed by low temperature annealing can be used for controllable local lifetime reduction in SiC devices. The dominant recombination centre is the Z1/2 defect, whose distribution can be set by irradiation energy and fluence. The local lifetime reduction, which improves diode recovery, can be monitored by OCVD response and simulated using the SRH model accounting for the Z1/2 defect.
- 5 June 2018
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 924, 436-439
Local Lifetime Control in 4H-SiC by Proton Irradiation
The effect of local lifetime control by proton irradiation on the OCVD response of a 10 kV SiC PiN diode was investigated. Carrier lifetime was reduced locally by irradiation with 800 keV protons at fluences up to 1x1011 cm-2. Radiation defects were characterized by DLTS and C-V profiling; excess carrier dynamics were measured by the OCVD and analyzed using the calibrated device simulator ATLAS from Silvaco, Inc. Results show that proton implantation followed by low temperature annealing can be used for controllable local lifetime reduction in SiC devices. The dominant recombination centre is the Z1/2 defect, whose distribution can be set by irradiation energy and fluence. The local lifetime reduction, which improves diode recovery, can be monitored by OCVD response and simulated using the SRH model accounting for the Z1/2 defect.
- 1 July 2017
- Published by Elsevier in Microelectronics Reliability
- Vol. 74, 58-66
Operation of 4H-SiC high voltage normally-OFF V-JFET in radiation hard conditions: Simulations and experiment
- 1 July 2017
- Published by Elsevier in Microelectronics Reliability
- Vol. 74, 58-66
Operation of 4H-SiC high voltage normally-OFF V-JFET in radiation hard conditions: Simulations and experiment
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 463-466
Lifetime Control in SiC PiN Diodes Using Radiation Defects
Application of radiation defects for lifetime control in contemporary SiC PiN diodes was investigated using the calibrated device simulator ATLAS from Silvaco, Inc. Recombination models accounting for the effect of deep levels introduced by the irradiation were set according to experimental results obtained by C-V and DLTS measurements performed on low-doped n-type SiC epilayers irradiated with 4.5 MeV electrons and 670 keV protons. Global (4.5 MeV electron irradiation) and local (700 keV proton irradiation) lifetime reduction was then applied on the 2A/10kV SiC PiN diode and the ON-state and reverse recovery characteristics were simulated and compared. Results show that the proton irradiation can substantially improve the trade‑off between the diode ON‑state and turn‑OFF losses. Compared to the electron irradiation, the local lifetime killing by protons allows achieving better trade-off and softer recovery curves.
- 15 May 2017
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 897, 463-466
Lifetime Control in SiC PiN Diodes Using Radiation Defects
Application of radiation defects for lifetime control in contemporary SiC PiN diodes was investigated using the calibrated device simulator ATLAS from Silvaco, Inc. Recombination models accounting for the effect of deep levels introduced by the irradiation were set according to experimental results obtained by C-V and DLTS measurements performed on low-doped n-type SiC epilayers irradiated with 4.5 MeV electrons and 670 keV protons. Global (4.5 MeV electron irradiation) and local (700 keV proton irradiation) lifetime reduction was then applied on the 2A/10kV SiC PiN diode and the ON-state and reverse recovery characteristics were simulated and compared. Results show that the proton irradiation can substantially improve the trade‑off between the diode ON‑state and turn‑OFF losses. Compared to the electron irradiation, the local lifetime killing by protons allows achieving better trade-off and softer recovery curves.
- 25 October 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (4)
Radiation resistance of wide-bandgap semiconductor power transistors
- 25 October 2016
- Published by Wiley in Physica Status Solidi (a)
- Vol. 214 (4)
Radiation resistance of wide-bandgap semiconductor power transistors