Mahdi Zamani
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Mahdi Zamani has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Javad Maghrebi
Ferdowsi University of Mashhad
5 shared publications - Sajad Abolpour Moshizi
School of Engineering, Macquarie University, Sydney, NSW 2109, Australia
4 shared publications - Seyed Rasoul Varedi
Department of Materials Engineering, ProPoliS Research Group, KU Leuven Bruges Campus, Spoorwegstraat 12, 8200 Bruges, Belgium
3 shared publications A. Malvandi
2 shared publicationsAli Reza Teymourtash
2 shared publications- Mahmood Norouzi
Faculty of Mechanical Engineering, Shahrood University of Technology , Shahrood
2 shared publications
Latest Publications
- 22 August 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 179
Optimization and numerical analysis of NACA0015 porous airfoil in static stall
- 22 August 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 179
Optimization and numerical analysis of NACA0015 porous airfoil in static stall
- 1 June 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 240 (7) , 1376-1397
A detailed analysis of end plate effects on the aerodynamic behavior of J-shaped Darrieus vertical axis wind turbine
The main purpose of this study is to investigate the effects of adding endplates on J-shaped blades of the Darrieus Vertical Axis Wind Turbine (VAWT) to improve aerodynamic characteristics. For this purpose, three types of blade profiles for Darrieus VAWT, including conventional airfoil (NACA0015), J-NACA0015, and J-EP NACA0015 are studied. The J-shaped blade is a notched NACA0015 profile, which is designed by eliminating a fraction of the pressure side of the conventional airfoil from maximum thickness, and J-EP is the J-shaped blade with endplates. To analyze the effects of end-plates on aerodynamic performance, all important parameters such as torque and power coefficients, lift and drag coefficients, tangential and normal force coefficients, vorticity volumetric structures, and aeroacoustics are studied. Results indicate that end plates reduce tip leakage flow, resulting in a more effective conversion of wind energy, such that the J-EP blades increase the power coefficient by 4.88% and 10.23% in comparison with J and conventional blades at optimal TSR (TSR = 1.6), respectively. At low TSRs, the torque coefficient for J-EP is higher than that of J and conventional blades, so that the J-EP blades increase the torque coefficient by 10.42% and 122.42% in comparison with J and conventional blades at TSR = 0.6, respectively. This implies that the self-starting capability of the turbine with J-EP blades is higher than that of the J and conventional blades. The volumetric representation of vorticity indicates that the J-EP blade generates fewer and smaller vortices downstream in comparison with other blades. Also, J-EP decreases the wake region behind the rotor and leads to a reduction in turbulence and boosts the flow uniformity at the flow downstream. The sound emitted from the turbine is investigated using the FW-H acoustic analogy method. The results indicate that the sound pressure level for the turbine with J and J-EP blades is lower than that of the conventional blade.
- 1 June 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 240 (7) , 1376-1397
A detailed analysis of end plate effects on the aerodynamic behavior of J-shaped Darrieus vertical axis wind turbine
The main purpose of this study is to investigate the effects of adding endplates on J-shaped blades of the Darrieus Vertical Axis Wind Turbine (VAWT) to improve aerodynamic characteristics. For this purpose, three types of blade profiles for Darrieus VAWT, including conventional airfoil (NACA0015), J-NACA0015, and J-EP NACA0015 are studied. The J-shaped blade is a notched NACA0015 profile, which is designed by eliminating a fraction of the pressure side of the conventional airfoil from maximum thickness, and J-EP is the J-shaped blade with endplates. To analyze the effects of end-plates on aerodynamic performance, all important parameters such as torque and power coefficients, lift and drag coefficients, tangential and normal force coefficients, vorticity volumetric structures, and aeroacoustics are studied. Results indicate that end plates reduce tip leakage flow, resulting in a more effective conversion of wind energy, such that the J-EP blades increase the power coefficient by 4.88% and 10.23% in comparison with J and conventional blades at optimal TSR (TSR = 1.6), respectively. At low TSRs, the torque coefficient for J-EP is higher than that of J and conventional blades, so that the J-EP blades increase the torque coefficient by 10.42% and 122.42% in comparison with J and conventional blades at TSR = 0.6, respectively. This implies that the self-starting capability of the turbine with J-EP blades is higher than that of the J and conventional blades. The volumetric representation of vorticity indicates that the J-EP blade generates fewer and smaller vortices downstream in comparison with other blades. Also, J-EP decreases the wake region behind the rotor and leads to a reduction in turbulence and boosts the flow uniformity at the flow downstream. The sound emitted from the turbine is investigated using the FW-H acoustic analogy method. The results indicate that the sound pressure level for the turbine with J and J-EP blades is lower than that of the conventional blade.
- Open Access
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Optimization and Numerical Analysis of NACA0015 Porous Airfoil in Static Stall
This paper investigates the effects of applying a porous layer to a NACA0015 airfoil surface under static stall conditions and its impact on aerodynamic performance, including lift coefficient, drag coefficient and glide ratio. For this purpose, a dense grid of geometric parameters including position, depth and length of porous layer was considered and optimized to find the optimal configuration of porous medium. Optimization was performed for both suction and pressure sides separately. A preliminary analysis was conducted using a Taguchi design of experiments (DoE) method by employing an L9 orthogonal array to identify the most influential parameter on objective function, CL,max, and to estimate its optimal level. In addition, a three-layer feedforward artificial neural network (ANN) was developed in MATLAB to find the optimal arrangement of three parameters for maximizing CL. The results showed that, based on a parameterization of porous airfoil geometry along with an ANN trained using CFD simulations, the proposed method could predict the value of CL with high accuracy and reduce computational times significantly. The greatest improvement in CL of suction side was achieved when the porous layer was placed in the mid-chord region, while the best aerodynamic performance for pressure side was obtained for porous layer placed near the leading edge with a smaller depth. This increases the maximum lift coefficient by 14%. Moreover, it was observed that applying a porous medium to both sides provides the greatest aerodynamic improvement, increasing the glide ratio at all angles of attack and delaying stall. Furthermore, the effects of porosity and the cell diameter of porous material were analyzed. It was observed that the optimum porosity value is 0.65, and that any reduction in the cell diameter from 0.32 to 0.02 mm increases the airfoil aerodynamic performance.
- 24 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessOptimization and Numerical Analysis of NACA0015 Porous Airfoil in Static Stall
This paper investigates the effects of applying a porous layer to a NACA0015 airfoil surface under static stall conditions and its impact on aerodynamic performance, including lift coefficient, drag coefficient and glide ratio. For this purpose, a dense grid of geometric parameters including position, depth and length of porous layer was considered and optimized to find the optimal configuration of porous medium. Optimization was performed for both suction and pressure sides separately. A preliminary analysis was conducted using a Taguchi design of experiments (DoE) method by employing an L9 orthogonal array to identify the most influential parameter on objective function, CL,max, and to estimate its optimal level. In addition, a three-layer feedforward artificial neural network (ANN) was developed in MATLAB to find the optimal arrangement of three parameters for maximizing CL. The results showed that, based on a parameterization of porous airfoil geometry along with an ANN trained using CFD simulations, the proposed method could predict the value of CL with high accuracy and reduce computational times significantly. The greatest improvement in CL of suction side was achieved when the porous layer was placed in the mid-chord region, while the best aerodynamic performance for pressure side was obtained for porous layer placed near the leading edge with a smaller depth. This increases the maximum lift coefficient by 14%. Moreover, it was observed that applying a porous medium to both sides provides the greatest aerodynamic improvement, increasing the glide ratio at all angles of attack and delaying stall. Furthermore, the effects of porosity and the cell diameter of porous material were analyzed. It was observed that the optimum porosity value is 0.65, and that any reduction in the cell diameter from 0.32 to 0.02 mm increases the airfoil aerodynamic performance.
- 6 June 2018
- Published by SAGE Publications in Wind Engineering
- Vol. 42 (6) , 647-664
Comparison between two-dimensional and three-dimensional computational fluid dynamics techniques for two straight-bladed vertical-axis wind turbines in inline arrangement
This study is dedicated to drawing a comparison between two- and three-dimensional approach capabilities for the simulation of two similar rotors placed in three inline (or tandem) arrangements. This arrangement is generally recognized as the worst-case scenario for the downwind rotor considering the vortices and disorders produced by the upwind rotor. The rotor in question with the diameter of 2.5 m is made up of three NACA0015 blades with the chord length and span size equal to 0.4 and 3 m, respectively. Based on the authors’ previous works, the shear stress transport model was selected for this comparative study. According to the results, there is an appreciable deviation in the aerodynamic performance of the upwind rotor predicted by the two-dimensional and three-dimensional simulation techniques. There is no tangible difference between the two-dimensional and three-dimensional results in terms of the averaged power output for the downwind rotor. However, the study of flow field employing different means like vortex structures, axial velocity, and even torque variation indicates that the two-dimensional approach is unable to achieve realistic and reliable output data. The introduced “pillar effect” regarding the dimensional limitations of the two-dimensional approach, which affects the vorticity shape and its dissipation, is plausible evidence for this discrepancy.- 6 June 2018
- Published by SAGE Publications in Wind Engineering
- Vol. 42 (6) , 647-664
Comparison between two-dimensional and three-dimensional computational fluid dynamics techniques for two straight-bladed vertical-axis wind turbines in inline arrangement
This study is dedicated to drawing a comparison between two- and three-dimensional approach capabilities for the simulation of two similar rotors placed in three inline (or tandem) arrangements. This arrangement is generally recognized as the worst-case scenario for the downwind rotor considering the vortices and disorders produced by the upwind rotor. The rotor in question with the diameter of 2.5 m is made up of three NACA0015 blades with the chord length and span size equal to 0.4 and 3 m, respectively. Based on the authors’ previous works, the shear stress transport model was selected for this comparative study. According to the results, there is an appreciable deviation in the aerodynamic performance of the upwind rotor predicted by the two-dimensional and three-dimensional simulation techniques. There is no tangible difference between the two-dimensional and three-dimensional results in terms of the averaged power output for the downwind rotor. However, the study of flow field employing different means like vortex structures, axial velocity, and even torque variation indicates that the two-dimensional approach is unable to achieve realistic and reliable output data. The introduced “pillar effect” regarding the dimensional limitations of the two-dimensional approach, which affects the vorticity shape and its dissipation, is plausible evidence for this discrepancy.- 6 March 2018
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 54 (9) , 2743-2760
Comparative study on the influence of depth, number and arrangement of dimples on the flow and heat transfer characteristics at turbulent flow regimes
- 6 March 2018
- Published by Springer Nature in Heat and Mass Transfer
- Vol. 54 (9) , 2743-2760
Comparative study on the influence of depth, number and arrangement of dimples on the flow and heat transfer characteristics at turbulent flow regimes
- 1 September 2017
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 65, 472-485
Nanofluid flow in micro-annular tubes at constant wall temperature considering the non-uniform distribution of nanoparticles
- 1 September 2017
- Published by Elsevier in European Journal of Mechanics - B/Fluids
- Vol. 65, 472-485
Nanofluid flow in micro-annular tubes at constant wall temperature considering the non-uniform distribution of nanoparticles
- 1 May 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 118, 328-338
Figure of merit for optimization of nanofluid flow in circular microchannel by adapting nanoparticle migration
- 1 May 2017
- Published by Elsevier in Applied Thermal Engineering
- Vol. 118, 328-338
Figure of merit for optimization of nanofluid flow in circular microchannel by adapting nanoparticle migration
- 1 May 2017
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 430, 36-46
Mixed convection of magnetohydrodynamic nanofluids inside microtubes at constant wall temperature
- 1 May 2017
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 430, 36-46
Mixed convection of magnetohydrodynamic nanofluids inside microtubes at constant wall temperature
- 1 March 2017
- Published by Elsevier in Advanced Powder Technology
- Vol. 28 (3) , 721-731
Fully developed mixed convection of nanofluids in microtubes at constant wall temperature: Anomalous heat transfer rate and thermal performance
- 1 March 2017
- Published by Elsevier in Advanced Powder Technology
- Vol. 28 (3) , 721-731
Fully developed mixed convection of nanofluids in microtubes at constant wall temperature: Anomalous heat transfer rate and thermal performance