MMMohammad Javad Maghrebi

Mohammad Javad Maghrebi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Mohammad Javad Maghrebi has a total of 53 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Optimization and Numerical Analysis of NACA0015 Porous Airfoil in Static Stall

    by Mahdi Zamani, Mohammad Javad Maghrebi, Ali Reza Teymourtash

    This paper investigates the effects of applying a porous layer to a NACA0015 airfoil surface under static stall conditions and its impact on aerodynamic performance, including lift coefficient, drag coefficient and glide ratio. For this purpose, a dense grid of geometric parameters including position, depth and length of porous layer was considered and optimized to find the optimal configuration of porous medium. Optimization was performed for both suction and pressure sides separately. A preliminary analysis was conducted using a Taguchi design of experiments (DoE) method by employing an L9 orthogonal array to identify the most influential parameter on objective function, CL,max, and to estimate its optimal level. In addition, a three-layer feedforward artificial neural network (ANN) was developed in MATLAB to find the optimal arrangement of three parameters for maximizing CL. The results showed that, based on a parameterization of porous airfoil geometry along with an ANN trained using CFD simulations, the proposed method could predict the value of CL with high accuracy and reduce computational times significantly. The greatest improvement in CL of suction side was achieved when the porous layer was placed in the mid-chord region, while the best aerodynamic performance for pressure side was obtained for porous layer placed near the leading edge with a smaller depth. This increases the maximum lift coefficient by 14%. Moreover, it was observed that applying a porous medium to both sides provides the greatest aerodynamic improvement, increasing the glide ratio at all angles of attack and delaying stall. Furthermore, the effects of porosity and the cell diameter of porous material were analyzed. It was observed that the optimum porosity value is 0.65, and that any reduction in the cell diameter from 0.32 to 0.02 mm increases the airfoil aerodynamic performance.

  • Enhancing thermal-hydraulic performance in curved pipes through optimal radial fin placement: A numerical investigation

    by Amin Ghaemian, Mohammad-Javad Maghrebi

    Increasing heat transfer in straight pipes, particularly in applications like heat exchangers, can be achieved by incorporating fins into the pipe wall. However, in curved pipes, the presence of more intricate flows resulting from centrifugal forces can alter this effect. The current study investigates how both the height and angular position of radial fins simultaneously influence the flow patterns within curved pipes. Adjusting the placement of radial fins is identified as a cost-effective and strategic approach to improve both the hydrodynamic and thermal efficiency in curved pipe systems. The numerical analysis focuses on studying laminar, incompressible flow in curved tubes with radial fins. The mass, momentum, and energy conservation equations in toroidal coordinates were discretized with the second-order finite difference method on a staggered grid, followed by their solution through the projection algorithm. The results indicate that adapting the angular position of the fins improves the thermal-hydraulic performance by 51.8%, 48.4%, 36.3%, and 20.6% for one to four fins, respectively. These changes are closely related to the behavior of the secondary flows. Furthermore, altering the height of the fins reveals that for three fins within the tube, the most optimal fin height is half of the tube radius. In other cases, a fin height equal to 0.7 multiplied by the tube radius provides the highest performance. From the numerical results, it is found that the primary factor affecting the heat transfer rate in curved pipes is the strength of secondary motions, while the generation of friction is influenced only by the axial velocity.


  • Open Access

    Leading Edge Radius Effects on VAWT Performance

    by N. Davandeh, M. J. Maghrebi

    Numerous studies have been conducted to investigate effect of blade geometry of vertical axis wind turbine performance. Most of the evaluations have focused on the airfoil series and airfoil geometry parameters such as thickness and camber of the airfoil. Few studies have examined the effect of other blade geometry parameters on the vertical axis wind turbine performance. In the present study, the effect of geometric change in leading-edge radius (LER) of a vertical axis wind turbine performance has been numerically studied. Hence, modified NACA 0021 airfoil profiles were created using the geometric method (CST). Then, the flow behavior around a Darrieus vertical axis wind turbine was simulated under the influence of the reduction and set-up coefficients of the leading-edge radius at a constant wind speed of 9 m/s and a tip speed ratio of 1.5 to 3.5 using the computational fluid dynamics. Additionally, the effects of the examined parameter (leading-edge radius) on fluid flow and aerodynamic performance coefficients, including the coefficients of power and torque, were investigated. The results indicated that the leading-edge radius affected the near wake flow of the turbine, and the optimization of leading-edge radius parameter controls the dynamic stall and reduces the formation of a vortex. Finally, the optimization of LER revealed that at 20% reduction in the LER the performance of the turbine at tip speed ratio of 1.5 was increased by more than 50%. This reinforces the self-starting capability of a Darrieus wind turbine.


  • Nondimensional Parameters’ Effects on Hybrid Darrieus–Savonius Wind Turbine Performance

    by Armin Roshan, Amir Sagharichi, Mohammad Javad Maghrebi

    Vertical axial wind turbines are the most commonly used turbines in residential and urban areas. This paper investigates the effect of combining Darrieus and Savonius wind turbines on power output and introduces a wind turbine with high starting torque addition to the wide working domain. A two-dimensional computational fluid dynamics transient simulation is developed, and a moving mesh is implemented for rotating moving parts. Comprehensive research has been carried out to investigate the effects of the initial overlap ratio (ɛ), arc angle Ø, and curvature (α) of Savonius blades on the performance of the turbine and 18 models are simulated at seven tip speed ratios. The results showed that combining the Darrieus turbine with the Savonius turbine has a favorable effect on self-starting performance. Also, it was observed that by changing each of the parameters, the primary model performance could be significantly improved. Finally, it is concluded that ɛ = 0.25, α = 0.25, and ∅ = 150 deg are the optimum values of the parameters which increase turbine power output compared to conventional vertical-axis turbines.


  • Stability and magnetization of Fe3O4/water nanofluid preparation characteristics using Taguchi method

    by Abazar Abadeh, Mohammad Passandideh-Fard, Mohammad Javad Maghrebi, Majid Mohammadi


  • Open Access

    Performance evaluation of floating solar chimney power plant in Iran: estimation of technology progression and cost investigation

    by Mohammad Javad Maghrebi, Reza Masoudi Nejad

    High direct solar radiation and the vast desert areas in Iran are the main factors to the attraction in using solar technologies such as floating solar chimney power plant (FSCPP) for electrical and thermal productions of energy. This article studies the performance of floating solar chimney technology for manufacturing purpose. In order to find the best area for the FSCPP, 14 different areas across the country are considered. The results revealed that FSCPP can produce 5–200 MW of electrical energy. Then a study was performed according to the return of finance rate, net price value, and finance return period criterions. The results showed that these power plants are able to be built in large scales of 100 and 200 MW of electricity with the annual capacity of 311 and 641 GW, respectively. However, a comparison between the cost analysis of two tested models shows that the 200 MW power plant with the cost of 14,273.64 Rials is more beneficial.‏


  • Numerical investigation of dimple effects on darrieus vertical axis wind turbine

    by Elyas Sobhani, Mohammad Ghaffari, Mohammad Javad Maghrebi