Yury V. Taran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yury V. Taran has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Juergen Schreiber
Independent Researcher, Dresden, Germany, Germany
5 shared publications A.M. Balagurov
Joint Institute for Nuclear Research
3 shared publicationsA. M. Balagurov
1 shared publicationAlexander Evans
Paul Scherrer Institute
1 shared publication- Alexander M. Korsunsky
University of Oxford
1 shared publication Anatoly M. Balagurov
Joint Institute for Nuclear Research
1 shared publication
Latest Publications
- 1 November 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 772, 109-115
Martensitic Transformation of Austenitic Stainless Steel Cruciform Geometry Sample by Biaxially Fatigued Cycling
A specifically designed cruciform-shaped austenitic stainless steel AISI 321 sample was subjected to ex-situ biaxial tension-compression cycling to establish ferromagnetic martensitic phase conversion under the action of plastic deformation. The time-of-flight neutron diffraction technique was employed for in-plane residual stress determination in this sample for both the austenitic and martensitic phases. The 2D data enabled determination of the macro-, micro-, hydro- and deviatoric contributions to the total phase stresses.
- 1 November 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 772, 109-115
Martensitic Transformation of Austenitic Stainless Steel Cruciform Geometry Sample by Biaxially Fatigued Cycling
A specifically designed cruciform-shaped austenitic stainless steel AISI 321 sample was subjected to ex-situ biaxial tension-compression cycling to establish ferromagnetic martensitic phase conversion under the action of plastic deformation. The time-of-flight neutron diffraction technique was employed for in-plane residual stress determination in this sample for both the austenitic and martensitic phases. The 2D data enabled determination of the macro-, micro-, hydro- and deviatoric contributions to the total phase stresses.
- 1 September 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 768-769, 697-704
Neutron Diffraction Investigation of Residual Stresses Induced in Niobium-Steel Bilayer Pipe Manufactured by Explosive Welding
Recently, reliable and hermetic joining of stainless steel to niobium pipes has been achieved with the explosive bonding technique. Joining of these two materials are essential to ensure production of a bimetallic transition element of pipe-type for its further use as a part of charged beam acceleration systems of the new generation. A non-destructive neutron diffraction investigation of the tri-axial strains along a radial cross-sectional line through the joint section has been performed. Residual stress results indicate inherently different natures in the residual stress values within the respective pipe sections. In the external stainless steel pipe the residual stresses are tensile, showing a sudden increase to 600 MPa as the interface is approached, whilst being compressive in the internal niobium pipe, not exceeding 650 MPa. A characteristic abrupt stress discontinuity exits at the interface region.
- 1 September 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 768-769, 697-704
Neutron Diffraction Investigation of Residual Stresses Induced in Niobium-Steel Bilayer Pipe Manufactured by Explosive Welding
Recently, reliable and hermetic joining of stainless steel to niobium pipes has been achieved with the explosive bonding technique. Joining of these two materials are essential to ensure production of a bimetallic transition element of pipe-type for its further use as a part of charged beam acceleration systems of the new generation. A non-destructive neutron diffraction investigation of the tri-axial strains along a radial cross-sectional line through the joint section has been performed. Residual stress results indicate inherently different natures in the residual stress values within the respective pipe sections. In the external stainless steel pipe the residual stresses are tensile, showing a sudden increase to 600 MPa as the interface is approached, whilst being compressive in the internal niobium pipe, not exceeding 650 MPa. A characteristic abrupt stress discontinuity exits at the interface region.
- 1 March 2008
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 571-572, 131-136
Neutron Diffraction Analysis of Stresses in an In-Plane Biaxially-Fatigued Stainless Steel Sample of Cruciform Geometry
An ex-situ in-plane biaxial low cycle fatigued sample of cruciform geometry made from austenitic stainless steel AISI 321 H was studied with the help of neutron diffraction strain scanning and also in-situ uniaxial loading using a stress rig on the FSD stress-diffractometer at the IBR-2 pulsed nuclear reactor (Dubna). The objectives of the experiment were to measure the macroscopic and microscopic residual stresses, crystallographic phase composition and the mechanical characteristics of the alloy under fatigue conditions. To the best of our knowledge, no neutron diffraction investigations of structural alloys subjected to biaxial loading have previously been reported. Experimental data interpretation and analysis are presented and discussed.
- 1 March 2008
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 571-572, 131-136
Neutron Diffraction Analysis of Stresses in an In-Plane Biaxially-Fatigued Stainless Steel Sample of Cruciform Geometry
An ex-situ in-plane biaxial low cycle fatigued sample of cruciform geometry made from austenitic stainless steel AISI 321 H was studied with the help of neutron diffraction strain scanning and also in-situ uniaxial loading using a stress rig on the FSD stress-diffractometer at the IBR-2 pulsed nuclear reactor (Dubna). The objectives of the experiment were to measure the macroscopic and microscopic residual stresses, crystallographic phase composition and the mechanical characteristics of the alloy under fatigue conditions. To the best of our knowledge, no neutron diffraction investigations of structural alloys subjected to biaxial loading have previously been reported. Experimental data interpretation and analysis are presented and discussed.
- 1 November 2007
- Published by Walter de Gruyter GmbH in Zeitschrift für Kristallographie
- Vol. 2007 (suppl_26) , 355-360
Triaxial residual stresses in composite tube from austenitic stainless steel with welded ferritic steel cladding
Triaxial residual stresses in composite tube from austenitic stainless steel with welded ferritic steel cladding was published in Tenth European Powder Diffraction Conference on page 355.
- 1 November 2007
- Published by Walter de Gruyter GmbH in Zeitschrift für Kristallographie
- Vol. 2007 (suppl_26) , 355-360
Triaxial residual stresses in composite tube from austenitic stainless steel with welded ferritic steel cladding
Triaxial residual stresses in composite tube from austenitic stainless steel with welded ferritic steel cladding was published in Tenth European Powder Diffraction Conference on page 355.
- 15 September 2006
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 524-525, 899-904
Fatigue Degradation and Martensitic Transformation of Austenitic Stainless Steel AlSi 321: New Results and Prospects
On ECRS-6 [1], we have presented first results of the researches of fatigue degradation and martensitic transformation of austenitic stainless steel AISI 321 by neutron diffraction stress analysis. A series of samples preliminary ex-situ cyclically fatigued at the frequency of 5 and 0.5 Hz was in-situ tested on the stress rig of the ENGIN instrument. In the high cycle fatigued (HCF) samples, the applied stress-elastic strain responses of austenite and martensite phases were find out to be strongly different as compared to the low cycle fatigued (LCF) samples, in which they are close. Moreover, the martensite Poisson ratio in the HCF-samples is almost twice to that of observed 0.28-0.30 in austenite and in both phases of the LCF-samples. With the purpose to search the reason of such unusual behavior of the martensite phase, one of the HCF-samples has been anew in-situ tested on the stress rig of the ENGIN-X in: 1) a LCF-mode at the frequency of 0.1 Hz to increase the fatigue level, and 2) a quasistatic mode to measure the applied stress-elastic strain responses of both phases. Also, two of the LCF-samples have been subjected to the ex-situ secondary HCF-testing at the frequency of 5 Hz and again in-situ measured on the ENGIN-X stress rig. Results of the mechanical characterization of phases in the twice fatigued austenitic stainless steel are presented and discussed.
- 15 September 2006
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 524-525, 899-904
Fatigue Degradation and Martensitic Transformation of Austenitic Stainless Steel AlSi 321: New Results and Prospects
On ECRS-6 [1], we have presented first results of the researches of fatigue degradation and martensitic transformation of austenitic stainless steel AISI 321 by neutron diffraction stress analysis. A series of samples preliminary ex-situ cyclically fatigued at the frequency of 5 and 0.5 Hz was in-situ tested on the stress rig of the ENGIN instrument. In the high cycle fatigued (HCF) samples, the applied stress-elastic strain responses of austenite and martensite phases were find out to be strongly different as compared to the low cycle fatigued (LCF) samples, in which they are close. Moreover, the martensite Poisson ratio in the HCF-samples is almost twice to that of observed 0.28-0.30 in austenite and in both phases of the LCF-samples. With the purpose to search the reason of such unusual behavior of the martensite phase, one of the HCF-samples has been anew in-situ tested on the stress rig of the ENGIN-X in: 1) a LCF-mode at the frequency of 0.1 Hz to increase the fatigue level, and 2) a quasistatic mode to measure the applied stress-elastic strain responses of both phases. Also, two of the LCF-samples have been subjected to the ex-situ secondary HCF-testing at the frequency of 5 Hz and again in-situ measured on the ENGIN-X stress rig. Results of the mechanical characterization of phases in the twice fatigued austenitic stainless steel are presented and discussed.
- 21 May 2000
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 347-349, 322-327
Neutron Diffraction Investigation of Low and High Cycle Fatigue Austenite Stainless Steels
- 21 May 2000
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 347-349, 322-327
Neutron Diffraction Investigation of Low and High Cycle Fatigue Austenite Stainless Steels
- 21 April 1998
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 278-281, 508-513
Neutron and X-Ray Diffraction Measurements of Residual Stresses in a Shape Welded Steel Tube
- 21 April 1998
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 278-281, 508-513
Neutron and X-Ray Diffraction Measurements of Residual Stresses in a Shape Welded Steel Tube
- 19 July 1996
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 228-231, 265-268
Equipment for Residual Stress Measurements with the High Resolution Fourier Diffractometer: Present Status and Prospects
- 19 July 1996
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 228-231, 265-268
Equipment for Residual Stress Measurements with the High Resolution Fourier Diffractometer: Present Status and Prospects
- 1 July 1994
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 166-169, 257-260
Possible Utilization of High Resolution Fourier Diffractometer at Reactor IBR-2 for Strain Measurements
- 1 July 1994
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 166-169, 257-260
Possible Utilization of High Resolution Fourier Diffractometer at Reactor IBR-2 for Strain Measurements
- 1 November 1963
- Published by Springer Nature in Atomic Energy
- Vol. 15 (5) , 1168-1169
On the design of a neutron spin rotator
- 1 November 1963
- Published by Springer Nature in Atomic Energy
- Vol. 15 (5) , 1168-1169
On the design of a neutron spin rotator