Adli Dimassi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Adli Dimassi has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Walter Lang
Institute for Microsensors, Actuators and Systems, Universität Bremen, 28359 Bremen, Germany
2 shared publications A S Herrmann
Faserinstitut Bremen e.V., Am Biologischen Garten 2, 28359 Bremen, Germany
1 shared publication- Arne Breede
Faserinstitut Bremen, e.V. FIBRE, Bremen, Germany
1 shared publication Axel S Herrmann
Faserinstitut Bremen e.V., Bremen, Germany
1 shared publicationAxel Siegfried Herrmann
Faserinstitut Bremen eV, University of Bremen, Bremen, Germany
1 shared publicationBernd Romahn
Weberit Werke Dräbing GmbH, Oberlahr, Germany
1 shared publication
Latest Publications
- 23 December 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 60 (27) , 2507-2524
Estimation of the three-dimensional permeability tensor of engineering textiles using artificial neural networks
The permeability quantifies the conductance of a textile as a porous medium for liquid flow and is an important material property for the liquid composite moulding (LCM) process. There are many different systems to measure and determine the permeability. The advantage of systems based on 3-dimensional flow progression is that the permeability tensor can be determined with one single measurement. However, derivation of the permeability values from the experimental data can be complex, especially when the flow front reaches the cavity walls and no analytical solution is available. In this study, a new artificial-intelligence-based evaluation method is presented for this case. An artificial neural network (ANN) is trained and tested with data from finite volume method (FVM) simulations. Different architectures and training data are used to evaluate the influences on the quality of the permeability estimation. With a minimum of 345 training data sets, a mean absolute percentage error (MAPE) of approx. 2.57 % was achieved during the training. The training can be further improved, when the simulation data is used multiple times. The trained ANNs are then applied to experimental data. Here, the estimation error for individual cases can be detected by a cross-check of two different ANNs, to improve reliability. A small deviation between the ANNs refers to a valid estimation. The developed method shows a promising approach to estimate the 3-dimensional permeability in a single experiment. It could also be used to extract permeability from flow in geometrically complex, real parts.
- 23 December 2025
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 60 (27) , 2507-2524
Estimation of the three-dimensional permeability tensor of engineering textiles using artificial neural networks
The permeability quantifies the conductance of a textile as a porous medium for liquid flow and is an important material property for the liquid composite moulding (LCM) process. There are many different systems to measure and determine the permeability. The advantage of systems based on 3-dimensional flow progression is that the permeability tensor can be determined with one single measurement. However, derivation of the permeability values from the experimental data can be complex, especially when the flow front reaches the cavity walls and no analytical solution is available. In this study, a new artificial-intelligence-based evaluation method is presented for this case. An artificial neural network (ANN) is trained and tested with data from finite volume method (FVM) simulations. Different architectures and training data are used to evaluate the influences on the quality of the permeability estimation. With a minimum of 345 training data sets, a mean absolute percentage error (MAPE) of approx. 2.57 % was achieved during the training. The training can be further improved, when the simulation data is used multiple times. The trained ANNs are then applied to experimental data. Here, the estimation error for individual cases can be detected by a cross-check of two different ANNs, to improve reliability. A small deviation between the ANNs refers to a valid estimation. The developed method shows a promising approach to estimate the 3-dimensional permeability in a single experiment. It could also be used to extract permeability from flow in geometrically complex, real parts.
- Open Access
- 18 August 2025
- Published by MDPI AG in Preprints.org
Manufacturing Routes for Short, Potentially Recycled Carbon Fibres to Close the Loop
Carbon fibre-reinforced composites are being more and more used since several years. In the same time the need for adequate methods to recycle fibres from industrial or post-industrial waste is rising. This paper investigates the state-of-the-art methodol-ogies for processing recycled Carbon Fibres (rCF) into reinforcement textiles, identifies key challenges, and presents novel production techniques aimed at optimizing their integration into textile structures for composites. Different processing methods are an-alysed and their impact on the mechanical properties of the composites is investigated on coupon level.
- 18 August 2025
- Published by MDPI AG in Preprints.org
Open AccessManufacturing Routes for Short, Potentially Recycled Carbon Fibres to Close the Loop
Carbon fibre-reinforced composites are being more and more used since several years. In the same time the need for adequate methods to recycle fibres from industrial or post-industrial waste is rising. This paper investigates the state-of-the-art methodol-ogies for processing recycled Carbon Fibres (rCF) into reinforcement textiles, identifies key challenges, and presents novel production techniques aimed at optimizing their integration into textile structures for composites. Different processing methods are an-alysed and their impact on the mechanical properties of the composites is investigated on coupon level.
- 17 May 2023
- Published by Elsevier in Materials Today Communications
- Vol. 35
Design, development and testing of 3D-printed conformal energy absorbing structures
- 17 May 2023
- Published by Elsevier in Materials Today Communications
- Vol. 35
Design, development and testing of 3D-printed conformal energy absorbing structures
- 5 October 2020
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (3) , 1285-1305
Analysis of open-hole-tension plates made of short fibre thermoplastic and reinforced with continuous fibre tailored inserts
In the present paper, the influence of tailored load introduction inserts applied to a bolt-loaded open-hole injection plate with different short glass fibre content is investigated. The tailored load introduction inserts made with a Tailored Fibre Placement (TFP) process, as well as open-hole injection plates without an insert were considered as reference samples. The samples were tested under tensile bolt-loading. The influence of the TFP-inserts on the load bearing properties of the open-hole injection plates was investigated. The test results show a huge increase of the load-carrying ability of the short-glass-fibre specimens when TFP-inserts are integrated. Moreover, the damage tolerance was dramatically improved as the specimens with integrated TFP-inserts did not fail abruptly and a residual strength higher than the strength of the test specimen without insert could be observed. However, the strength of the test specimen with integrated insert did not exceed the strength of the insert itself in most cases.
- 5 October 2020
- Published by SAGE Publications in Journal of Thermoplastic Composite Materials
- Vol. 36 (3) , 1285-1305
Analysis of open-hole-tension plates made of short fibre thermoplastic and reinforced with continuous fibre tailored inserts
In the present paper, the influence of tailored load introduction inserts applied to a bolt-loaded open-hole injection plate with different short glass fibre content is investigated. The tailored load introduction inserts made with a Tailored Fibre Placement (TFP) process, as well as open-hole injection plates without an insert were considered as reference samples. The samples were tested under tensile bolt-loading. The influence of the TFP-inserts on the load bearing properties of the open-hole injection plates was investigated. The test results show a huge increase of the load-carrying ability of the short-glass-fibre specimens when TFP-inserts are integrated. Moreover, the damage tolerance was dramatically improved as the specimens with integrated TFP-inserts did not fail abruptly and a residual strength higher than the strength of the test specimen without insert could be observed. However, the strength of the test specimen with integrated insert did not exceed the strength of the insert itself in most cases.
- 15 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (22) , 10654-10661
Embedded Wireless Sensor Systems for Resin Flow Monitoring in Glass and Carbon Fiber Composites
This paper presents a novel wireless sensor system that can be embedded in both glass and carbon fiber composites allowing for the first time to wirelessly measure pressure and temperature throughout the laminate during infusion, giving an insight into the process behaviour. The obtained data can be used for modelling the resin flow inside the composite, which is required for simulation and for speeding up the design of new parts. We suggest a system, which uses wireless data transmission that does not hurt the vacuum seal, even for sensors deeply embedded between conductive carbon fibers. The current sensor system gives an accurate pressure reading (mbar resolution) that provides information about the pressure gradient in the whole laminate. For carbon fibers, the sensors are soldered on a self-made, flexible, 10 μ-thick polyimide cable, which is resistant to high temperatures. This makes the system minimally invasive since only a 2mm × 2.5mm system remains inside the laminate.
- 15 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 19 (22) , 10654-10661
Embedded Wireless Sensor Systems for Resin Flow Monitoring in Glass and Carbon Fiber Composites
This paper presents a novel wireless sensor system that can be embedded in both glass and carbon fiber composites allowing for the first time to wirelessly measure pressure and temperature throughout the laminate during infusion, giving an insight into the process behaviour. The obtained data can be used for modelling the resin flow inside the composite, which is required for simulation and for speeding up the design of new parts. We suggest a system, which uses wireless data transmission that does not hurt the vacuum seal, even for sensors deeply embedded between conductive carbon fibers. The current sensor system gives an accurate pressure reading (mbar resolution) that provides information about the pressure gradient in the whole laminate. For carbon fibers, the sensors are soldered on a self-made, flexible, 10 μ-thick polyimide cable, which is resistant to high temperatures. This makes the system minimally invasive since only a 2mm × 2.5mm system remains inside the laminate.
- Open Access
- 27 December 2017
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 22 (2) , 349-369
Experimental investigation of Tied Foam Core sandwich compression performance
Carbon and glass dry fibre bundles were inserted into a ROHACELL® 71HERO polymethacrylimide foam core under a specific inclination angle and pin pattern in order to enhance the compressive strength and stiffness of the core material. Flatwise compression tests were conducted on pin-reinforced sandwich specimens and unreinforced sandwich to investigate the effect of pin volume fraction and pin material on the compressive mechanical properties and energy absorption characteristics. X-ray computed tomography was performed on tested specimens to investigate the failure modes under compressive loads. It was concluded that the compressive strength is mainly controlled by pin failure due to bending and compression loads at pin base. Moreover, increasing the pin volume fraction improved the compressive properties of the sandwich but using glass fibre pins instead of carbon fibre pins led to a higher increase of the absorbed crushing energy. Finally, an existing analytical model to predict the compressive strength and stiffness has been tested and evaluated.
- 27 December 2017
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 22 (2) , 349-369
Open AccessExperimental investigation of Tied Foam Core sandwich compression performance
Carbon and glass dry fibre bundles were inserted into a ROHACELL® 71HERO polymethacrylimide foam core under a specific inclination angle and pin pattern in order to enhance the compressive strength and stiffness of the core material. Flatwise compression tests were conducted on pin-reinforced sandwich specimens and unreinforced sandwich to investigate the effect of pin volume fraction and pin material on the compressive mechanical properties and energy absorption characteristics. X-ray computed tomography was performed on tested specimens to investigate the failure modes under compressive loads. It was concluded that the compressive strength is mainly controlled by pin failure due to bending and compression loads at pin base. Moreover, increasing the pin volume fraction improved the compressive properties of the sandwich but using glass fibre pins instead of carbon fibre pins led to a higher increase of the absorbed crushing energy. Finally, an existing analytical model to predict the compressive strength and stiffness has been tested and evaluated.
- Open Access
- 18 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 339
Piezoresistive Pressure Sensors for Resin Flow Monitoring in Carbon Fibre-Reinforced Composite
Using piezoresistive pressure sensors and in-situ measurement of pressure gradient, the infusion of resin in fiber reinforced composite can be optimized. The optimization of resin flow in Vacuum Assisted Resin Infusion (VARI) is necessary to produce high-quality fibre-reinforced composites. To control the resin infusion process, piezoresistive pressure sensors are embedded to detect the resin flow and resin pressure in Carbon Fibre Reinforced Polymer (CFRP). The measured pressure validates the accuracy of analytical calculations, based on Darcy’s law in a porous medium. The sensors are of small size and therefore do not affect the natural flow of the resin.
- 18 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 339
Open AccessPiezoresistive Pressure Sensors for Resin Flow Monitoring in Carbon Fibre-Reinforced Composite
Using piezoresistive pressure sensors and in-situ measurement of pressure gradient, the infusion of resin in fiber reinforced composite can be optimized. The optimization of resin flow in Vacuum Assisted Resin Infusion (VARI) is necessary to produce high-quality fibre-reinforced composites. To control the resin infusion process, piezoresistive pressure sensors are embedded to detect the resin flow and resin pressure in Carbon Fibre Reinforced Polymer (CFRP). The measured pressure validates the accuracy of analytical calculations, based on Darcy’s law in a porous medium. The sensors are of small size and therefore do not affect the natural flow of the resin.
- Open Access
- 10 March 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 118 (1) , 012012
Experimental study of the mechanical behaviour of pin reinforced foam core sandwich materials under shear load
Sandwich structures with a lightweight closed cell hard foam core have the potential to be used in primary structures of commercial aircrafts. Compared to honeycomb core sandwich, the closed cell foam core sandwich overcomes the issue of moisture take up and makes the manufacturing of low priced and highly integrated structures possible. However, lightweight foam core sandwich materials are prone to failure by localised external loads like low velocity impacts. Invisible cracks could grow in the foam core and threaten the integrity of the structure. In order to enhance the out-of-plane properties of foam core sandwich structures and to improve the damage tolerance (DT) dry fibre bundles are inserted in the foam core. The pins are infused with resin and co-cured with the dry fabric face sheets in an out-of-autoclave process. This study presents the results obtained from shear tests following DIN 53294-standard, on flat sandwich panels. All panels were manufactured with pin-reinforcement manufactured with the Tied Foam Core Technology (TFC) developed by Airbus. The effects of pin material (CFRP and GFRP) and pin volume fraction on the shear properties of the sandwich structure and the crack propagation were investigated and compared to a not pinned reference. It has been concluded that the pin volume fraction has a remarkable effect on the shear properties and damage tolerance of the observed structure. Increasing the pin volume fraction makes the effect of crack redirection more obvious and conserves the integrity of the structure after crack occurrence.
- 10 March 2016
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 118 (1) , 012012
Open AccessExperimental study of the mechanical behaviour of pin reinforced foam core sandwich materials under shear load
Sandwich structures with a lightweight closed cell hard foam core have the potential to be used in primary structures of commercial aircrafts. Compared to honeycomb core sandwich, the closed cell foam core sandwich overcomes the issue of moisture take up and makes the manufacturing of low priced and highly integrated structures possible. However, lightweight foam core sandwich materials are prone to failure by localised external loads like low velocity impacts. Invisible cracks could grow in the foam core and threaten the integrity of the structure. In order to enhance the out-of-plane properties of foam core sandwich structures and to improve the damage tolerance (DT) dry fibre bundles are inserted in the foam core. The pins are infused with resin and co-cured with the dry fabric face sheets in an out-of-autoclave process. This study presents the results obtained from shear tests following DIN 53294-standard, on flat sandwich panels. All panels were manufactured with pin-reinforcement manufactured with the Tied Foam Core Technology (TFC) developed by Airbus. The effects of pin material (CFRP and GFRP) and pin volume fraction on the shear properties of the sandwich structure and the crack propagation were investigated and compared to a not pinned reference. It has been concluded that the pin volume fraction has a remarkable effect on the shear properties and damage tolerance of the observed structure. Increasing the pin volume fraction makes the effect of crack redirection more obvious and conserves the integrity of the structure after crack occurrence.