René Bos
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
René Bos has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Alexander Petrus van Bavel
Shell Global Solutions International BV 3 , Grasweg 31, 1031 HW Amsterdam
1 shared publication - Ashim Giyanani
Wind Energy Research Group, Faculty of Aerospace Engineering, Delft University of Technology, Kluyverweg 1, Postbus 5058, 2600 GB Delft, The Netherlands
1 shared publication Bhumana Teressa
1 shared publication- Dick Veldkamp
Suzlon Energy Ltd. Netherlands Branch, Aero & Loads Dept, Jan Tinbergenstraat 290. 7559 ST Hengelo, The Netherlands
1 shared publication Himanshu Goyal
1 shared publicationJan Harmsen
1 shared publication
Latest Publications
- Open Access
- 13 September 2026
- Published by Elsevier in SSRN Electronic Journal
Design and scale-up investigation of a Joule-heated steam methane reforming reactor using first principles
Electrification of conventionally fired chemical reactors is emerging as a viable pathway toward decarbonizing industrial processes, offering reduced CO$_2$ emissions together with flexible and compact heat-generation capabilities. Joule-heated catalytic reactors are a promising route to electrify high-temperature endothermic processes. However, their design remains largely empirical as the coupled electrical, thermal, flow, and reaction phenomena that govern them are not well characterized. This work develops a one-dimensional multiphysics model of a Joule-heated tubular steam methane reformer in which the reactor wall serves as both a resistive heating element and a catalyst support. The model resolves the underlying physico-chemical processes in a fully coupled manner and is validated against reported experiments on an electrically heated tubular reformer. Scaling analysis of the governing equations identifies the dimensionless groups that control reactor behavior. We show that the dimensionless solid-fluid thermal coupling parameter distinguishes mass-transfer-controlled operation from thermally controlled operation. This criterion clarifies which resistance limits conversion at a given scale and provides the basis for scale-up rules relating tube length, diameter, wall thickness, and applied power. Finally, the ability of Joule heating to impose a spatially varying power input is examined by comparing uniform and non-uniform axial power profiles. Redistributing the same total power along the tube reshapes the temperature profile, offsets the endothermic cold spot near the inlet, and alters methane conversion and hydrogen productivity in a Joule-heated reactor. Spatial power distribution acts as an additional design variable for electrified reactors.
- 13 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessDesign and scale-up investigation of a Joule-heated steam methane reforming reactor using first principles
Electrification of conventionally fired chemical reactors is emerging as a viable pathway toward decarbonizing industrial processes, offering reduced CO$_2$ emissions together with flexible and compact heat-generation capabilities. Joule-heated catalytic reactors are a promising route to electrify high-temperature endothermic processes. However, their design remains largely empirical as the coupled electrical, thermal, flow, and reaction phenomena that govern them are not well characterized. This work develops a one-dimensional multiphysics model of a Joule-heated tubular steam methane reformer in which the reactor wall serves as both a resistive heating element and a catalyst support. The model resolves the underlying physico-chemical processes in a fully coupled manner and is validated against reported experiments on an electrically heated tubular reformer. Scaling analysis of the governing equations identifies the dimensionless groups that control reactor behavior. We show that the dimensionless solid-fluid thermal coupling parameter distinguishes mass-transfer-controlled operation from thermally controlled operation. This criterion clarifies which resistance limits conversion at a given scale and provides the basis for scale-up rules relating tube length, diameter, wall thickness, and applied power. Finally, the ability of Joule heating to impose a spatially varying power input is examined by comparing uniform and non-uniform axial power profiles. Redistributing the same total power along the tube reshapes the temperature profile, offsets the endothermic cold spot near the inlet, and alters methane conversion and hydrogen productivity in a Joule-heated reactor. Spatial power distribution acts as an additional design variable for electrified reactors.
- 12 April 2023
- Published by Walter de Gruyter GmbH
- p. 75-108
4 Residence time distribution and mixing theory
4 Residence time distribution and mixing theory was published in Multiphase Reactors on page 75.
- 12 April 2023
- Published by Walter de Gruyter GmbH
- p. 75-108
4 Residence time distribution and mixing theory
4 Residence time distribution and mixing theory was published in Multiphase Reactors on page 75.
- Open Access
- 14 September 2016
- Published by MDPI AG in Remote Sensing
- Vol. 8 (9) , 758
Assessing the Severity of Wind Gusts with Lidar
Lidars have gained a lot of popularity in the field of wind energy, partly because of their potential to be used for wind turbine control. By scanning the oncoming wind field, any threats such as gusts can be detected early and high loads can be avoided by taking preventive actions. Unfortunately, lidars suffer from some inherent weaknesses that hinder measuring gusts; e.g., the averaging of high-frequency fluctuations and only measuring along the line of sight). This paper proposes a method to construct a useful signal from a lidar by fitting a homogeneous Gaussian velocity field to a set of scattered measurements. The output signal, an along-wind force, acts as a measure for the damaging potential of an oncoming gust and is shown to agree with the rotor-effective wind speed (a similar control input, but derived directly from the wind turbine’s shaft torque). Low data availability and the disadvantage of not knowing the velocity between the lidar beams is translated into uncertainty and integrated in the output signal. This allows a designer to establish a control strategy based on risk, with the ultimate goal to reduce the extreme loads during operation.
- 14 September 2016
- Published by MDPI AG in Remote Sensing
- Vol. 8 (9) , 758
Open AccessAssessing the Severity of Wind Gusts with Lidar
Lidars have gained a lot of popularity in the field of wind energy, partly because of their potential to be used for wind turbine control. By scanning the oncoming wind field, any threats such as gusts can be detected early and high loads can be avoided by taking preventive actions. Unfortunately, lidars suffer from some inherent weaknesses that hinder measuring gusts; e.g., the averaging of high-frequency fluctuations and only measuring along the line of sight). This paper proposes a method to construct a useful signal from a lidar by fitting a homogeneous Gaussian velocity field to a set of scattered measurements. The output signal, an along-wind force, acts as a measure for the damaging potential of an oncoming gust and is shown to agree with the rotor-effective wind speed (a similar control input, but derived directly from the wind turbine’s shaft torque). Low data availability and the disadvantage of not knowing the velocity between the lidar beams is translated into uncertainty and integrated in the output signal. This allows a designer to establish a control strategy based on risk, with the ultimate goal to reduce the extreme loads during operation.
- Open Access
- 1 September 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 753 (4) , 042021
A method to find the 50-year extreme load during production
An important yet difficult task in the design of wind turbines is to assess the extreme load behaviour, most notably finding the 50-year load. Where existing methods often focus on ways to extrapolate from small sample sizes, this paper proposes a different approach. It combines generating constrained gusts in turbulence fields, Delaunay tessellation to assign probabilities and a genetic algorithm to find the desired load in an efficient way. The individual parts of the method are verified and the results are compared to both crude Monte Carlo and importance sampling. We found that using a genetic algorithm is a promising approach to find the 50-year load, with only a small number of load cases (~103) to be evaluated and requiring no user input but an appropriate fitness function.
- 1 September 2016
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 753 (4) , 042021
Open AccessA method to find the 50-year extreme load during production
An important yet difficult task in the design of wind turbines is to assess the extreme load behaviour, most notably finding the 50-year load. Where existing methods often focus on ways to extrapolate from small sample sizes, this paper proposes a different approach. It combines generating constrained gusts in turbulence fields, Delaunay tessellation to assign probabilities and a genetic algorithm to find the desired load in an efficient way. The individual parts of the method are verified and the results are compared to both crude Monte Carlo and importance sampling. We found that using a genetic algorithm is a promising approach to find the 50-year load, with only a small number of load cases (~103) to be evaluated and requiring no user input but an appropriate fitness function.