Alfredo J. Tolley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Alfredo J. Tolley has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Laura Noel García
Instituto de Ciencias Astronómicas, de la Tierra y del Espacio Universidad Nacional de San Juan, CONICET San Juan Argentina
4 shared publications - Fernando Diego Carazo
IMA, Facultad de Ingeniería, Universidad Nacional de San Juan, San Juan, Argentina
2 shared publications - Roberto Enrique Boeri
Metallurgy Division, INTEMA CONICET-UNMdP, Mar del Plata, Argentina
2 shared publications A. Gabriel Sathicq
1 shared publicationAdriana M. Condó
Centro Atómico Bariloche, CNEA, 8400 San Carlos de Bariloche, Argentina
1 shared publication- Alberto Baruj
Centro Atómico Bariloche, CNEA, 8400 S.C. de Bariloche, Argentina
1 shared publication
Latest Publications
- 18 February 2022
- Published by SAGE Publications in Materials Science and Technology
- Vol. 38 (4) , 230-236
Effect of cold deformation in quench and tempered medium-carbon steel bars microstructure
Tempered AISI 4140 steel bars were processed by cold drawing. An effective deformation of ≈0.9 was achieved. The quench and tempered, and the subsequently deformed microstructures were analysed by optical and transmission electron microscopy. Intralath, interlath and spherically shaped carbides were identified in both cases. The deformed specimens revealed a mixed structure of thinned laths and dislocations cell-blocks composed of cell-block and cell boundaries. After the deformation process, alignment and fragmentation of the carbides occurred, mainly of those located in lath boundaries what would explain the partial preservation of the lath boundaries after drawing as they would arrest the destruction of lath martensite boundaries. These microstructural characteristics shall play an important role to enhance grain refinement in subsequent heat treatments.
- 18 February 2022
- Published by SAGE Publications in Materials Science and Technology
- Vol. 38 (4) , 230-236
Effect of cold deformation in quench and tempered medium-carbon steel bars microstructure
Tempered AISI 4140 steel bars were processed by cold drawing. An effective deformation of ≈0.9 was achieved. The quench and tempered, and the subsequently deformed microstructures were analysed by optical and transmission electron microscopy. Intralath, interlath and spherically shaped carbides were identified in both cases. The deformed specimens revealed a mixed structure of thinned laths and dislocations cell-blocks composed of cell-block and cell boundaries. After the deformation process, alignment and fragmentation of the carbides occurred, mainly of those located in lath boundaries what would explain the partial preservation of the lath boundaries after drawing as they would arrest the destruction of lath martensite boundaries. These microstructural characteristics shall play an important role to enhance grain refinement in subsequent heat treatments.
- 29 November 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (4) , 1164-1174
Formation of Cu-rich Nanoprecipitates in Cu Containing Pearlitic SGI
- 29 November 2020
- Published by Springer Nature in International Journal of Metalcasting
- Vol. 15 (4) , 1164-1174
Formation of Cu-rich Nanoprecipitates in Cu Containing Pearlitic SGI
- 24 September 2019
- Published by SAGE Publications in Materials Science and Technology
- Vol. 35 (18) , 2252-2258
Identification of Cu-rich precipitates in pearlitic spheroidal graphite cast irons
This investigation studies the partitioning of Mn and Cu – and Si– between ferrite and cementite in the pearlite of two alloys containing similar Mn and Si concentrations, but different Cu contents, keeping the Cu concentration within the usual industrial limits. The results confirm the partitioning of all the elements between ferrite and cementite during pearlite growth. Furthermore, the presence of nanometric Cu-rich precipitates was detected for an alloy with typical Cu contents for achieving pearlitic structures in spheroidal graphite cast irons. This might be linked to the microsegregation of Cu developed during the solidification step. These precipitates have not been reported before and cannot be ignored as they can affect the transformation kinetics and the mechanical properties of the alloy.
- 24 September 2019
- Published by SAGE Publications in Materials Science and Technology
- Vol. 35 (18) , 2252-2258
Identification of Cu-rich precipitates in pearlitic spheroidal graphite cast irons
This investigation studies the partitioning of Mn and Cu – and Si– between ferrite and cementite in the pearlite of two alloys containing similar Mn and Si concentrations, but different Cu contents, keeping the Cu concentration within the usual industrial limits. The results confirm the partitioning of all the elements between ferrite and cementite during pearlite growth. Furthermore, the presence of nanometric Cu-rich precipitates was detected for an alloy with typical Cu contents for achieving pearlitic structures in spheroidal graphite cast irons. This might be linked to the microsegregation of Cu developed during the solidification step. These precipitates have not been reported before and cannot be ignored as they can affect the transformation kinetics and the mechanical properties of the alloy.
- 1 July 2005
- Published by Elsevier in Scripta Materialia
- Vol. 53 (1) , 109-114
Ion irradiation induced formation of close packed particles in β Cu–Zn–Al
- 1 July 2005
- Published by Elsevier in Scripta Materialia
- Vol. 53 (1) , 109-114
Ion irradiation induced formation of close packed particles in β Cu–Zn–Al