JitKang Lim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
JitKang Lim has a total of 135 co-authors. Here are the top co-authors by number of shared publications:
- Abdul Latif Ahmad
Universiti Sains Malaysia
27 shared publications - Boon Seng Ooi
School of Chemical Engineering, Universiti Sains Malaysia, Engineering Campus, 14300 Nibong Tebal, Pulau Pinang, Malaysia
11 shared publications - Siew Chun Low
School of Chemical Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang, Malaysia
10 shared publications Abdul Latif Ahmad
School of Chemical Engineering, Universiti Sains Malaysia, Nibong Tebal, Penang, 14300, Malaysia
9 shared publicationsC.J.C. Derek
9 shared publicationsPey Yi Toh
9 shared publications
Latest Publications
- Open Access
- 31 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (36) , 26275-26289
Network Formation in Poly(diallyldimethylammonium chloride)/Polyphosphoric Acid Polyelectrolyte Complexes and Their Role in Sand Stabilization
Soil erosion remains a pressing global environmental challenge, and polyelectrolyte complexes (PECs) have emerged as promising stabilizing agents for soil erosion control. However, the mechanistic basis of their performance, particularly the complex interplay between the structure of PECs, rheological behavior, and the associated flow field within the surrounding environment, remains poorly understood. In this study, we constructed PECs by combining a short-chain polyanion and a long-chain polycation to form a polymeric network, using polyphosphoric acid (PPA) and poly(diallyldimethylammonium chloride) (PDDA) as the model components. Electrophoretic mobility (EPM) measurements, hydrodynamic diameter analysis by dynamic light scattering (DLS), and quartz crystal microbalance with dissipation (QCM-D) collectively reveal an electrostatically driven self-assembly process in which long-chain PDDA provides the scaffold while short-chain PPA acts as a molecular connector. Rheological measurements show that the shear resistance of the PDDA/PPA network, characterized by the effective shear rate γ̇ and the characteristic shear stress τ at the G′ maximum, can be tuned by adjusting the PPA dosage. Macroscale hydrodynamic shear tests further demonstrate a strong positive correlation between consolidated-sand stability and the rheology-derived network strength, with both γ̇ and τ at the G′ maximum reaching a maximum at a PDDA:PPA monomer molar ratio of 1:5. Scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDX) directly visualizes interparticle physical bridging that promotes sand aggregation. Collectively, these results suggest that the PPA-regulated strength of the PECs network is an important factor influencing sand-stabilization performance. Such findings shift the design philosophy of sand stabilizers from conventional surface adhesion toward the internal structural engineering of particle-bridging networks.
- 31 August 2026
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 42 (36) , 26275-26289
Open AccessNetwork Formation in Poly(diallyldimethylammonium chloride)/Polyphosphoric Acid Polyelectrolyte Complexes and Their Role in Sand Stabilization
Soil erosion remains a pressing global environmental challenge, and polyelectrolyte complexes (PECs) have emerged as promising stabilizing agents for soil erosion control. However, the mechanistic basis of their performance, particularly the complex interplay between the structure of PECs, rheological behavior, and the associated flow field within the surrounding environment, remains poorly understood. In this study, we constructed PECs by combining a short-chain polyanion and a long-chain polycation to form a polymeric network, using polyphosphoric acid (PPA) and poly(diallyldimethylammonium chloride) (PDDA) as the model components. Electrophoretic mobility (EPM) measurements, hydrodynamic diameter analysis by dynamic light scattering (DLS), and quartz crystal microbalance with dissipation (QCM-D) collectively reveal an electrostatically driven self-assembly process in which long-chain PDDA provides the scaffold while short-chain PPA acts as a molecular connector. Rheological measurements show that the shear resistance of the PDDA/PPA network, characterized by the effective shear rate γ̇ and the characteristic shear stress τ at the G′ maximum, can be tuned by adjusting the PPA dosage. Macroscale hydrodynamic shear tests further demonstrate a strong positive correlation between consolidated-sand stability and the rheology-derived network strength, with both γ̇ and τ at the G′ maximum reaching a maximum at a PDDA:PPA monomer molar ratio of 1:5. Scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy (SEM-EDX) directly visualizes interparticle physical bridging that promotes sand aggregation. Collectively, these results suggest that the PPA-regulated strength of the PECs network is an important factor influencing sand-stabilization performance. Such findings shift the design philosophy of sand stabilizers from conventional surface adhesion toward the internal structural engineering of particle-bridging networks.
- Open Access
- 8 February 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (7) , 11049-11067
Poly(Ionic Liquid)s Dispersants for Lubricants: A Review on Structure–Property Relationships
Poly(ionic liquid)s (PILs) have emerged as a versatile class of materials whose structural diversity, ranging from backbone chemistry and side-chain functionality to counterion type, governs their aggregation behavior, interfacial adsorption, and nanoscale self-assembly. These attributes make PILs attractive candidates for advanced applications in lubrication, dispersion stabilization, and sustainable functional materials. However, correlating molecular architecture with macroscopic performance remains a significant challenge, largely due to the complex and dynamic nature of their structural evolution. This review critically examines recent progress in understanding PIL structure–property relationships through multiscale characterization. Surface tension provides insight into interfacial activity, while small-angle X-ray scattering and small-angle neutron scattering elucidate nanoscale organization and hierarchical assembly. Complementarily, zeta-potential measurements quantify electrostatic interactions and the colloidal stability. Together, these techniques enable a coherent framework linking molecular design, interfacial phenomena, and bulk performance. Key knowledge gaps are highlighted, including the need for in situ and operando studies under realistic operating conditions as well as the integration of experimental techniques with computational modeling to capture dynamic restructuring and long-term stability. By synthesizing insights across structural chemistry, scattering techniques, and interfacial science, this review establishes future research directions for the rational design of PILs as next-generation dispersants, lubricants, and sustainable advanced materials.
- 8 February 2026
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 11 (7) , 11049-11067
Open AccessPoly(Ionic Liquid)s Dispersants for Lubricants: A Review on Structure–Property Relationships
Poly(ionic liquid)s (PILs) have emerged as a versatile class of materials whose structural diversity, ranging from backbone chemistry and side-chain functionality to counterion type, governs their aggregation behavior, interfacial adsorption, and nanoscale self-assembly. These attributes make PILs attractive candidates for advanced applications in lubrication, dispersion stabilization, and sustainable functional materials. However, correlating molecular architecture with macroscopic performance remains a significant challenge, largely due to the complex and dynamic nature of their structural evolution. This review critically examines recent progress in understanding PIL structure–property relationships through multiscale characterization. Surface tension provides insight into interfacial activity, while small-angle X-ray scattering and small-angle neutron scattering elucidate nanoscale organization and hierarchical assembly. Complementarily, zeta-potential measurements quantify electrostatic interactions and the colloidal stability. Together, these techniques enable a coherent framework linking molecular design, interfacial phenomena, and bulk performance. Key knowledge gaps are highlighted, including the need for in situ and operando studies under realistic operating conditions as well as the integration of experimental techniques with computational modeling to capture dynamic restructuring and long-term stability. By synthesizing insights across structural chemistry, scattering techniques, and interfacial science, this review establishes future research directions for the rational design of PILs as next-generation dispersants, lubricants, and sustainable advanced materials.
- 12 March 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (11) , 7151-7159
Silicon/Silica Colloidal Waste in the Semiconductor Industry: Challenges in Recovery and Potential Use
The backgrinding of silicon (Si) wafers has resulted in a loss of ∼70% of valuable Si materials. Consequently, an effluent known as diluted backgrinding wastewater (DBGW) is generated, containing nanosized silicon/silica colloids. Here, we discussed the challenges associated with the effective separation of Si-based waste from the DBGW based upon two perspectives, namely, a nanosized effect and a colloidal stability effect. Then, we revealed the limitation with the currently used coagulation-flocculation approach, which introduces impurities into the highly pure Si. Membrane-based filtration techniques have been adopted, but the serious fouling problem associated with colloidal Si/SiO2 renders them almost impractical. Apart from that, the potential use of highly pure Si waste generated in the semiconductor industry in lithium ion batteries (LIBs) has been discussed. This Perspective aims to provide insights into the challenges associated with the Si recovery from DBGW and suggests its potential use in LIBs.
- 12 March 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (11) , 7151-7159
Silicon/Silica Colloidal Waste in the Semiconductor Industry: Challenges in Recovery and Potential Use
The backgrinding of silicon (Si) wafers has resulted in a loss of ∼70% of valuable Si materials. Consequently, an effluent known as diluted backgrinding wastewater (DBGW) is generated, containing nanosized silicon/silica colloids. Here, we discussed the challenges associated with the effective separation of Si-based waste from the DBGW based upon two perspectives, namely, a nanosized effect and a colloidal stability effect. Then, we revealed the limitation with the currently used coagulation-flocculation approach, which introduces impurities into the highly pure Si. Membrane-based filtration techniques have been adopted, but the serious fouling problem associated with colloidal Si/SiO2 renders them almost impractical. Apart from that, the potential use of highly pure Si waste generated in the semiconductor industry in lithium ion batteries (LIBs) has been discussed. This Perspective aims to provide insights into the challenges associated with the Si recovery from DBGW and suggests its potential use in LIBs.
- 2 February 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (5) , 3572-3582
Magnetic Capture of Functionalized Nanoscale Zerovalent Iron for Soil Remediation: A Feasibility Study on Transport Control
Nanoscale zerovalent iron (nZVI) has been proposed as a promising nanomaterial for soil remediation. However, injecting nZVI into contaminated sites to target and treat pollutant sources may pose potential environmental risks due to its colloidal stability and mobility in the environment. In this regard, this study assessed the feasibility of implementing magnetic capture of surface-functionalized nZVI in soil environments under the influence of the convective flow current. Here, functionalized nZVI particles were prepared by introducing carboxymethyl cellulose (CMC) as a stabilizing agent during the synthesis of nZVI by using the liquid-phase reduction method. The functionalized nZVI particles were then injected into a two-dimensional flow column containing a sand matrix with a high gradient magnetic trap (HGMT) embedded within the system. Particle transports in both the absence and presence of a magnetic field were recorded by using a digital camera, and the breakthrough curves were generated from the data collected spectrophotometrically. The results showed that the relative breakthrough concentration of nZVI decreased from 0.92 to nearly zero, with a delayed breakthrough time as the applied magnetic field strength increased from zero (no magnetic field) to 0.093 T, demonstrating a 100% capture efficiency. It was found that the magnetic capture for the nZVI particles was contributed by two mechanisms: (1) low gradient magnetic separation (LGMS), driven by the penetrating magnetic field from the permanent magnets, and (2) high gradient magnetic separation (HGMS), which occurred near the wire surfaces within the HGMT section magnetized by the permanent magnets. Findings in this work have proven the feasibility of magnetic separation as a control strategy for nanoparticle applications in environmental remediation.
- 2 February 2025
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 41 (5) , 3572-3582
Magnetic Capture of Functionalized Nanoscale Zerovalent Iron for Soil Remediation: A Feasibility Study on Transport Control
Nanoscale zerovalent iron (nZVI) has been proposed as a promising nanomaterial for soil remediation. However, injecting nZVI into contaminated sites to target and treat pollutant sources may pose potential environmental risks due to its colloidal stability and mobility in the environment. In this regard, this study assessed the feasibility of implementing magnetic capture of surface-functionalized nZVI in soil environments under the influence of the convective flow current. Here, functionalized nZVI particles were prepared by introducing carboxymethyl cellulose (CMC) as a stabilizing agent during the synthesis of nZVI by using the liquid-phase reduction method. The functionalized nZVI particles were then injected into a two-dimensional flow column containing a sand matrix with a high gradient magnetic trap (HGMT) embedded within the system. Particle transports in both the absence and presence of a magnetic field were recorded by using a digital camera, and the breakthrough curves were generated from the data collected spectrophotometrically. The results showed that the relative breakthrough concentration of nZVI decreased from 0.92 to nearly zero, with a delayed breakthrough time as the applied magnetic field strength increased from zero (no magnetic field) to 0.093 T, demonstrating a 100% capture efficiency. It was found that the magnetic capture for the nZVI particles was contributed by two mechanisms: (1) low gradient magnetic separation (LGMS), driven by the penetrating magnetic field from the permanent magnets, and (2) high gradient magnetic separation (HGMS), which occurred near the wire surfaces within the HGMT section magnetized by the permanent magnets. Findings in this work have proven the feasibility of magnetic separation as a control strategy for nanoparticle applications in environmental remediation.
- 3 December 2023
- Published by Wiley in Electrophoresis
- Vol. 45 (5-6) , 357-368
Navigating the microenvironment with flip and turn under quadrupole magnetophoretic steering control: Nanosphere‐ and nanorod‐coated microbead
The spatiotemporal accuracy of microscale magnetophoresis has improved significantly over the course of several decades of development. However, most of the studies so far were using magnetic microbead composed of nanosphere particle for magnetophoretic actuation purpose. Here, we developed an in‐house method for magnetic sample analysis called quadrupole magnetic steering control (QMSC). QMSC was used to study the magnetophoretic behavior of polystyrene microbeads decorated with iron oxide nanospheres‐coated polystyrene microbeads (IONSs‐PS) and iron oxide nanorods‐coated polystyrene microbeads (IONRs‐PS) under the influence of a quadrupole low field gradient. During a 4‐s QMSC experiment, the IONSs‐PS and IONRs‐PS were navigated to perform 180° flip and 90° turn formations, and their kinematic results (2 s before and 2 s after the flip/turn) were measured and compared. The results showed that the IONRs‐PS suffered from significant kinematic disproportion, translating a highly uneven amount of kinetic energy from the same magnitude of magnetic control. Combining the kinematic analysis, transmission electron microscopy micrographs, and vibrating sample magnetometry measurements, it was found that the IONRs‐PS experienced higher fluid drag force and had lower consistency than the IONSs‐PS due to its extensive open fractal nanorod structure on the bead surface and uneven magnetization, which was attributed to its ferrimagnetic nature.
- 3 December 2023
- Published by Wiley in Electrophoresis
- Vol. 45 (5-6) , 357-368
Navigating the microenvironment with flip and turn under quadrupole magnetophoretic steering control: Nanosphere‐ and nanorod‐coated microbead
The spatiotemporal accuracy of microscale magnetophoresis has improved significantly over the course of several decades of development. However, most of the studies so far were using magnetic microbead composed of nanosphere particle for magnetophoretic actuation purpose. Here, we developed an in‐house method for magnetic sample analysis called quadrupole magnetic steering control (QMSC). QMSC was used to study the magnetophoretic behavior of polystyrene microbeads decorated with iron oxide nanospheres‐coated polystyrene microbeads (IONSs‐PS) and iron oxide nanorods‐coated polystyrene microbeads (IONRs‐PS) under the influence of a quadrupole low field gradient. During a 4‐s QMSC experiment, the IONSs‐PS and IONRs‐PS were navigated to perform 180° flip and 90° turn formations, and their kinematic results (2 s before and 2 s after the flip/turn) were measured and compared. The results showed that the IONRs‐PS suffered from significant kinematic disproportion, translating a highly uneven amount of kinetic energy from the same magnitude of magnetic control. Combining the kinematic analysis, transmission electron microscopy micrographs, and vibrating sample magnetometry measurements, it was found that the IONRs‐PS experienced higher fluid drag force and had lower consistency than the IONSs‐PS due to its extensive open fractal nanorod structure on the bead surface and uneven magnetization, which was attributed to its ferrimagnetic nature.
- 17 November 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (48) , 17270-17285
Exploring the Impact of Surface Functionalization on the Reaction, Magnetophoretic, and Collective Transport Behavior of Nanoscale Zerovalent Iron
This study provides a systematic analysis of the transport and magnetophoretic behavior of nanoscale zerovalent iron (nZVI) particles, both bare and surface functionalized by poly(ethylene glycol) (PEG) and carboxymethyl cellulose (CMC), after undergoing a chemical reaction. Here, a simple and well-investigated chemical reaction of methyl orange (MO) degradation by nZVI was used as a model reaction system, and the sand column transport and low-gradient magnetophoretic profiles of the nanoparticles were measured before and after the reaction. The results were compared over time and analyzed in the context of extended Derjaguin-Landau-Verwey-Overbeek (DLVO) theory to understand the particle interactions involved. The colloidal stability of both bare and functionalized nZVI particles was enhanced after the reaction due to the consumption of metallic Fe content, resulting in a significant drop in their magnetic properties. As a result, they exhibited improved mobility across the sand column and a slower magnetophoretic collection rate compared to the unreacted particles. Here, the colloidal filtration theory (CFT) was employed to analyze the transport behavior of nZVI particles across the packed sand column. It has been observed that the surface properties of the reacted functionalized particles changed, possibly due to the entrapment of degraded products within the polymer adlayer. Moreover, quartz crystal microbalance with dissipation (QCM-D) measurements were performed to reveal the viscoelastic contribution of the adlayer formed by both bare and functionalized nZVI particles after the reaction on influencing their transport behavior across the sand column. Finally, we proposed the implementation of a high-gradient magnetic trap (HGMT) to reduce the transport distance of the colloidally stable CMC-nZVI, both before and after the reaction. This study sheds light on the behavioral changes of iron nanoparticles after the reaction and highlights environmental concerns regarding the presence of reacted nanoparticles.
- 17 November 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (48) , 17270-17285
Exploring the Impact of Surface Functionalization on the Reaction, Magnetophoretic, and Collective Transport Behavior of Nanoscale Zerovalent Iron
This study provides a systematic analysis of the transport and magnetophoretic behavior of nanoscale zerovalent iron (nZVI) particles, both bare and surface functionalized by poly(ethylene glycol) (PEG) and carboxymethyl cellulose (CMC), after undergoing a chemical reaction. Here, a simple and well-investigated chemical reaction of methyl orange (MO) degradation by nZVI was used as a model reaction system, and the sand column transport and low-gradient magnetophoretic profiles of the nanoparticles were measured before and after the reaction. The results were compared over time and analyzed in the context of extended Derjaguin-Landau-Verwey-Overbeek (DLVO) theory to understand the particle interactions involved. The colloidal stability of both bare and functionalized nZVI particles was enhanced after the reaction due to the consumption of metallic Fe content, resulting in a significant drop in their magnetic properties. As a result, they exhibited improved mobility across the sand column and a slower magnetophoretic collection rate compared to the unreacted particles. Here, the colloidal filtration theory (CFT) was employed to analyze the transport behavior of nZVI particles across the packed sand column. It has been observed that the surface properties of the reacted functionalized particles changed, possibly due to the entrapment of degraded products within the polymer adlayer. Moreover, quartz crystal microbalance with dissipation (QCM-D) measurements were performed to reveal the viscoelastic contribution of the adlayer formed by both bare and functionalized nZVI particles after the reaction on influencing their transport behavior across the sand column. Finally, we proposed the implementation of a high-gradient magnetic trap (HGMT) to reduce the transport distance of the colloidally stable CMC-nZVI, both before and after the reaction. This study sheds light on the behavioral changes of iron nanoparticles after the reaction and highlights environmental concerns regarding the presence of reacted nanoparticles.
- 31 May 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (7) , 2295-2308
Shape‐controlled synthesis of polyaniline and its synergistic effect with reduced graphene oxide for the fabrication of flexible electrode
Composite of reduced graphene oxide (rGO) and polyaniline (PANI) have gained much attention in industrial applications especially for the fabrication of supercapacitor and flexible sensors. Nevertheless, existing studies mainly focus on the application efficiency and are lacking information on how morphology of the nanoparticles can affect the electrode properties. Herein, the effects of shape of PANI on the electrode resistivity were systematically investigated. PANI of different shapes was synthesized using different reagents, namely H2SO4, CH3COOH, H2O, and NH3·H2O, which induced formation of globule, tube, plate, and flake‐like PANI. rGO‐PANI composite was then produced using ex situ method and cast on a PVC substrate to form a flexible electrode. The rGO‐PANI globules displayed superior electrical conductivity owing to its high protonation level. The resistivity of this sample was found to be 0.015 ± 0.002 Ωcm, which is lowest as compared to the counterparts. Interestingly, electrode made of rGO‐PANI plates had a slightly lower electrical resistivity than rGO‐PANI tubes despite its low protonation level. It is speculate that the aspect ratio characteristic of the PANI might have influence the electron mobility. rGO‐PANI electrode was found to exhibit a lower specific resistivity than pure rGO and pure PANI, evincing the presence of synergism.
- 31 May 2023
- Published by Wiley in Polymer Engineering & Science
- Vol. 63 (7) , 2295-2308
Shape‐controlled synthesis of polyaniline and its synergistic effect with reduced graphene oxide for the fabrication of flexible electrode
Composite of reduced graphene oxide (rGO) and polyaniline (PANI) have gained much attention in industrial applications especially for the fabrication of supercapacitor and flexible sensors. Nevertheless, existing studies mainly focus on the application efficiency and are lacking information on how morphology of the nanoparticles can affect the electrode properties. Herein, the effects of shape of PANI on the electrode resistivity were systematically investigated. PANI of different shapes was synthesized using different reagents, namely H2SO4, CH3COOH, H2O, and NH3·H2O, which induced formation of globule, tube, plate, and flake‐like PANI. rGO‐PANI composite was then produced using ex situ method and cast on a PVC substrate to form a flexible electrode. The rGO‐PANI globules displayed superior electrical conductivity owing to its high protonation level. The resistivity of this sample was found to be 0.015 ± 0.002 Ωcm, which is lowest as compared to the counterparts. Interestingly, electrode made of rGO‐PANI plates had a slightly lower electrical resistivity than rGO‐PANI tubes despite its low protonation level. It is speculate that the aspect ratio characteristic of the PANI might have influence the electron mobility. rGO‐PANI electrode was found to exhibit a lower specific resistivity than pure rGO and pure PANI, evincing the presence of synergism.
- 30 March 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (14) , 4904-4916
Low-Gradient Magnetophoresis of Nanospheres and Nanorods through a Single Layer of Paper
The possible magnetophoretic migration of iron oxide nanoparticles through the cellulosic matrix within a single layer of paper is challenging with its underlying mechanism remained unclear. Even with the recent advancements of theoretical understanding on magnetophoresis, mainly driven by cooperative and hydrodynamics phenomena, the contributions of these two mechanisms on possible penetration of magnetic nanoparticles through cellulosic matrix of paper have yet been proven. Here, by using iron oxide nanoparticles (IONPs), both nanospheres and nanorods, we have investigated the migration kinetics of these nanoparticles through grade 4 Whatman filter paper with a particle retention of 20-25 μm. By performing droplet tracking experiments, the real-time stained area growth of the particle droplet on the filter paper, under the influences of a grade N40 NdFeB magnet, were recorded. Our results show that the spatial and temporal expansion of the IONP stain is biased toward the magnet and such an effect is dependent on (i) particle concentration and (ii) particle shape. The kinetics data were first analyzed by treating it as a radial wicking fluid, and later the IONP distribution within the cellulosic matrix was investigated by optical microscopy. The macroscopic flow front velocities of the stained area ranged from 259 μm/s to 16 040 μm/s. Moreover, the microscopic magnetophoretic velocity of nanorod cluster was also successfully measured as ∼214 μm/s. Findings in this work have indirectly revealed the strong influence of cooperative magnetophoresis and the engineering feasibility of paper-based magnetophoretic technology by taking advantage of magnetoshape anisotropy effect of the particles.
- 30 March 2023
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 39 (14) , 4904-4916
Low-Gradient Magnetophoresis of Nanospheres and Nanorods through a Single Layer of Paper
The possible magnetophoretic migration of iron oxide nanoparticles through the cellulosic matrix within a single layer of paper is challenging with its underlying mechanism remained unclear. Even with the recent advancements of theoretical understanding on magnetophoresis, mainly driven by cooperative and hydrodynamics phenomena, the contributions of these two mechanisms on possible penetration of magnetic nanoparticles through cellulosic matrix of paper have yet been proven. Here, by using iron oxide nanoparticles (IONPs), both nanospheres and nanorods, we have investigated the migration kinetics of these nanoparticles through grade 4 Whatman filter paper with a particle retention of 20-25 μm. By performing droplet tracking experiments, the real-time stained area growth of the particle droplet on the filter paper, under the influences of a grade N40 NdFeB magnet, were recorded. Our results show that the spatial and temporal expansion of the IONP stain is biased toward the magnet and such an effect is dependent on (i) particle concentration and (ii) particle shape. The kinetics data were first analyzed by treating it as a radial wicking fluid, and later the IONP distribution within the cellulosic matrix was investigated by optical microscopy. The macroscopic flow front velocities of the stained area ranged from 259 μm/s to 16 040 μm/s. Moreover, the microscopic magnetophoretic velocity of nanorod cluster was also successfully measured as ∼214 μm/s. Findings in this work have indirectly revealed the strong influence of cooperative magnetophoresis and the engineering feasibility of paper-based magnetophoretic technology by taking advantage of magnetoshape anisotropy effect of the particles.
- 13 July 2021
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 37 (30) , 9192-9201
The Transport Behavior of a Biflagellated Microswimmer before and after Cargo Loading
The changes in the transport behavior of a microswimmer before and after cargo loading are crucial to understanding and control of the motion of a biohybrid microbot. In this work, we show the change in swimming behavior of biflagellated microalgae Chlamydomonas reinhardtii picking up a 4.5 μm polystyrene microbead upon collision. The microswimmer changed from linear forward motion into helical motion upon the attachment of the cargo and swam with a decreased swimming velocity. We revealed the helical motion of the microswimmer upon cargo loading due to suppression of flagella by image analysis of magnified time-lapse images of C. reinhardtii with one microbead attached at the anterior end (between the flagella). Furthered suppression on the flagellum imposed by the loading of the second cargo has led to increased oscillation per displacement traveled and decreased swimming velocity. Moreover, the microswimmer with a microbead attached at the posterior end swam with swimming velocity close to free swimming microalgae and did not exhibit helical swimming behavior. The experimental results and analysis showed that the loading location of the cargo has a great influence over the swimming behavior of the microswimmer. Furthermore, the work balance calculation and mathematical analysis based on Lighthill’s model are well consistent with our experimental findings.
- 13 July 2021
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 37 (30) , 9192-9201
The Transport Behavior of a Biflagellated Microswimmer before and after Cargo Loading
The changes in the transport behavior of a microswimmer before and after cargo loading are crucial to understanding and control of the motion of a biohybrid microbot. In this work, we show the change in swimming behavior of biflagellated microalgae Chlamydomonas reinhardtii picking up a 4.5 μm polystyrene microbead upon collision. The microswimmer changed from linear forward motion into helical motion upon the attachment of the cargo and swam with a decreased swimming velocity. We revealed the helical motion of the microswimmer upon cargo loading due to suppression of flagella by image analysis of magnified time-lapse images of C. reinhardtii with one microbead attached at the anterior end (between the flagella). Furthered suppression on the flagellum imposed by the loading of the second cargo has led to increased oscillation per displacement traveled and decreased swimming velocity. Moreover, the microswimmer with a microbead attached at the posterior end swam with swimming velocity close to free swimming microalgae and did not exhibit helical swimming behavior. The experimental results and analysis showed that the loading location of the cargo has a great influence over the swimming behavior of the microswimmer. Furthermore, the work balance calculation and mathematical analysis based on Lighthill’s model are well consistent with our experimental findings.
- 2 July 2021
- Published by Wiley in Electrophoresis
- Vol. 42 (21-22) , 2303-2328
Design and operation of magnetophoretic systems at microscale: Device and particle approaches
Combining both device and particle designs are the essential concepts to be considered in magnetophoretic system development. Researcher efforts are often dedicated to only one of these design aspects and neglecting the interplay between them. Herein, to bring out importance of the idea of integration between device and particle, we reviewed the working principle of magnetophoretic system (includes both device and particle design concepts). Since, the magnetophoretic force is influenced by both field gradient and magnetization volume, hence, accurate prediction of the magnetophoretic force is relying on the availability of information on both parameters. In device design, we focus on the different strategies used to create localized high‐field gradient. For particle design, we emphasize on the scaling between hydrodynamic size and magnetization volume. Moreover, we also briefly discussed the importance of magnetoshape anisotropy related to particle design aspect of magnetophoretic systems. Next, we illustrated the need for integration between device and particle design using microscale applications of magnetophoretic systems, include magnetic tweezers and microfluidic systems, as our working example. On the basis of our discussion, we highlighted several promising examples of microscale magnetophoretic systems which greatly utilized the interplay between device and particle design. Further, we concluded the review with several factors that possibly resulted in the lack of research efforts related to device and particle design integration.
- 2 July 2021
- Published by Wiley in Electrophoresis
- Vol. 42 (21-22) , 2303-2328
Design and operation of magnetophoretic systems at microscale: Device and particle approaches
Combining both device and particle designs are the essential concepts to be considered in magnetophoretic system development. Researcher efforts are often dedicated to only one of these design aspects and neglecting the interplay between them. Herein, to bring out importance of the idea of integration between device and particle, we reviewed the working principle of magnetophoretic system (includes both device and particle design concepts). Since, the magnetophoretic force is influenced by both field gradient and magnetization volume, hence, accurate prediction of the magnetophoretic force is relying on the availability of information on both parameters. In device design, we focus on the different strategies used to create localized high‐field gradient. For particle design, we emphasize on the scaling between hydrodynamic size and magnetization volume. Moreover, we also briefly discussed the importance of magnetoshape anisotropy related to particle design aspect of magnetophoretic systems. Next, we illustrated the need for integration between device and particle design using microscale applications of magnetophoretic systems, include magnetic tweezers and microfluidic systems, as our working example. On the basis of our discussion, we highlighted several promising examples of microscale magnetophoretic systems which greatly utilized the interplay between device and particle design. Further, we concluded the review with several factors that possibly resulted in the lack of research efforts related to device and particle design integration.