Mardali Yousefpour
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mardali Yousefpour has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
Amir Zareidoost
7 shared publicationsEhsan Borhani
5 shared publicationsShabnam Hamedzadeh
4 shared publicationsZahra Taherian
4 shared publicationsAli Habibolahzadeh
Semnan University
3 shared publicationsKian Kasraee
3 shared publications
Latest Publications
- Open Access
- 25 August 2026
- Published by Elsevier in SSRN Electronic Journal
A Novel Frit-Encapsulation Strategy to Stabilize Graphene Oxide During High-Temperature Solid-State Synthesis of Bi-2223Superconductor
This study introduces a facile, low-cost, and practical encapsulation strategy to integrate thermally labile graphene oxide (GO) sheets into the Bi-2223 (Bi₂Sr₂Ca₂Cu₃O₁₀₊ₓ) high-temperature superconductor without structural degradation. The novelty lies in adapting the classical ceramics-industry technique of fritting to the solid-state synthesis of HTS superconductors: GO sheets are first embedded within a low-melting 1PbO–1SiO₂ glassy matrix (~478 °C softening point), and the resulting composite is subsequently employed as a single synergistic additive in the Bi-2223 precursor. The Bi-2223 sample containing 1 wt.% of the GO/frit composite was compared with reference samples doped with pristine GO, PbO, SiO₂, and a plain frit. X-ray diffraction (XRD), differential thermal analysis (DTA), scanning and transmission electron microscopy (SEM/TEM), FTIR, and Raman spectroscopy were used for microstructural and chemical characterization. Transport and magnetic measurements revealed that the GO/frit-doped sample exhibited the highest critical temperature (Tc = 109 K) and the highest critical current density (Jc = 9.5 × 10² A/cm²) among all compositions, confirming that the proposed frit-encapsulation strategy effectively preserves GO functionality above its decomposition threshold and provides a synergistic enhancement to the superconducting performance of Bi-2223.
- 25 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Novel Frit-Encapsulation Strategy to Stabilize Graphene Oxide During High-Temperature Solid-State Synthesis of Bi-2223Superconductor
This study introduces a facile, low-cost, and practical encapsulation strategy to integrate thermally labile graphene oxide (GO) sheets into the Bi-2223 (Bi₂Sr₂Ca₂Cu₃O₁₀₊ₓ) high-temperature superconductor without structural degradation. The novelty lies in adapting the classical ceramics-industry technique of fritting to the solid-state synthesis of HTS superconductors: GO sheets are first embedded within a low-melting 1PbO–1SiO₂ glassy matrix (~478 °C softening point), and the resulting composite is subsequently employed as a single synergistic additive in the Bi-2223 precursor. The Bi-2223 sample containing 1 wt.% of the GO/frit composite was compared with reference samples doped with pristine GO, PbO, SiO₂, and a plain frit. X-ray diffraction (XRD), differential thermal analysis (DTA), scanning and transmission electron microscopy (SEM/TEM), FTIR, and Raman spectroscopy were used for microstructural and chemical characterization. Transport and magnetic measurements revealed that the GO/frit-doped sample exhibited the highest critical temperature (Tc = 109 K) and the highest critical current density (Jc = 9.5 × 10² A/cm²) among all compositions, confirming that the proposed frit-encapsulation strategy effectively preserves GO functionality above its decomposition threshold and provides a synergistic enhancement to the superconducting performance of Bi-2223.
- Open Access
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Enhanced Corrosion Protection and Self-Healing Performance of Eco-Friendly Epoxy-Based Smart Coatings Incorporating Porous Silica-Loaded Sodium Phosphate and Gum Arabic using Molecular Dynamics Simulations
This study investigates the corrosion protection and self-healing properties of epoxy-based smart coatings incorporating porous silica, sodium phosphate, and Gum Arabic on carbon steel in a 3.5 wt% NaCl environment. Porous silica served as a carrier for controlled inhibitor release, leveraging its high surface area and porosity. Sodium phosphate acted as an anodic inhibitor, forming a protective iron phosphate layer, while Gum Arabic, a natural polysaccharide, enhanced self-healing through its barrier-forming and viscoelastic properties. Electrochemical impedance spectroscopy (EIS) and PDP revealed that EPOXY-Silica-GA exhibited the highest corrosion resistance (1049.4 ohm.cm⁻²) and a 93% reduction in corrosion rate, followed by EPOXY-Silica-SP-GA (92%) and EPOXY-Silica-SP (86%). Field-emission scanning electron microscopy (FE-SEM) and energy-dispersive X-ray spectroscopy (EDS) confirmed uniform particle distribution and reduced chloride/iron penetration in optimized coatings post-salt spray testing. Fourier-transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) validated chemical interactions and structural changes. Additionally, molecular dynamics (MD) simulations provided atomic-scale insights into the mechanisms, revealing strong interactions between phosphate ions and the iron surface, reduced diffusion of chloride ions in the presence of porous silica and Gum Arabic, and enhanced hydrogen bonding facilitating controlled inhibitor release and defect sealing in the self-healing process. The superior performance of EPOXY-Silica-GA is attributed to Gum Arabic’s self-healing capability, while the multilayer system in EPOXY-Silica-SP-GA enhanced durability. This eco-friendly coating offers a sustainable solution for steel protection in harsh environments, with potential applications in marine and industrial settings.
- 4 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessEnhanced Corrosion Protection and Self-Healing Performance of Eco-Friendly Epoxy-Based Smart Coatings Incorporating Porous Silica-Loaded Sodium Phosphate and Gum Arabic using Molecular Dynamics Simulations
This study investigates the corrosion protection and self-healing properties of epoxy-based smart coatings incorporating porous silica, sodium phosphate, and Gum Arabic on carbon steel in a 3.5 wt% NaCl environment. Porous silica served as a carrier for controlled inhibitor release, leveraging its high surface area and porosity. Sodium phosphate acted as an anodic inhibitor, forming a protective iron phosphate layer, while Gum Arabic, a natural polysaccharide, enhanced self-healing through its barrier-forming and viscoelastic properties. Electrochemical impedance spectroscopy (EIS) and PDP revealed that EPOXY-Silica-GA exhibited the highest corrosion resistance (1049.4 ohm.cm⁻²) and a 93% reduction in corrosion rate, followed by EPOXY-Silica-SP-GA (92%) and EPOXY-Silica-SP (86%). Field-emission scanning electron microscopy (FE-SEM) and energy-dispersive X-ray spectroscopy (EDS) confirmed uniform particle distribution and reduced chloride/iron penetration in optimized coatings post-salt spray testing. Fourier-transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) validated chemical interactions and structural changes. Additionally, molecular dynamics (MD) simulations provided atomic-scale insights into the mechanisms, revealing strong interactions between phosphate ions and the iron surface, reduced diffusion of chloride ions in the presence of porous silica and Gum Arabic, and enhanced hydrogen bonding facilitating controlled inhibitor release and defect sealing in the self-healing process. The superior performance of EPOXY-Silica-GA is attributed to Gum Arabic’s self-healing capability, while the multilayer system in EPOXY-Silica-SP-GA enhanced durability. This eco-friendly coating offers a sustainable solution for steel protection in harsh environments, with potential applications in marine and industrial settings.
- Open Access
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Role of Li addition in governing solidification-induced microstructural evolution and electrochemical degradation of as-cast Mg-3Zn-3Sn alloys
The solidification of biodegradable magnesium (Mg) alloys significantly influences their strength and degradation over time. This study examined the effect of adding lithium (0–5 wt.%) to affects the microstructure and corrosion of as-cast Mg-3Zn-3Sn alloys. Unlike previous studies on thermomechanical processing, we focused on the unique role of lithium (Li) during the initial crystallization, where it acts as a grain refiner and modulator of the phase distribution. SEM-EDS and Rietveld-refined XRD showed that Li specifically transformed the microstructure from coarse dendrites to finer, more uniform grains. At 4 wt.% Li, secondary phases are better distributed, and grain-to-grain connections are stronger. The Mg-3Zn-3Sn-4Li (ZTL334) alloy achieved a compressive strength of 385 MPa and ductility of 26% in its as-cast state. Electrochemical tests in Dulbecco’s Modified Eagle Medium (DMEM) showed that 4 wt. % Li makes the degradation pattern more even, which lowers the corrosion current density to 199 μA/cm2 and reduces micro-galvanic effects at grain boundaries. These results show that adding Li can change the microstructure of solidification, which is a step toward producing high-performance biodegradable implants without any extra work.
- 24 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessRole of Li addition in governing solidification-induced microstructural evolution and electrochemical degradation of as-cast Mg-3Zn-3Sn alloys
The solidification of biodegradable magnesium (Mg) alloys significantly influences their strength and degradation over time. This study examined the effect of adding lithium (0–5 wt.%) to affects the microstructure and corrosion of as-cast Mg-3Zn-3Sn alloys. Unlike previous studies on thermomechanical processing, we focused on the unique role of lithium (Li) during the initial crystallization, where it acts as a grain refiner and modulator of the phase distribution. SEM-EDS and Rietveld-refined XRD showed that Li specifically transformed the microstructure from coarse dendrites to finer, more uniform grains. At 4 wt.% Li, secondary phases are better distributed, and grain-to-grain connections are stronger. The Mg-3Zn-3Sn-4Li (ZTL334) alloy achieved a compressive strength of 385 MPa and ductility of 26% in its as-cast state. Electrochemical tests in Dulbecco’s Modified Eagle Medium (DMEM) showed that 4 wt. % Li makes the degradation pattern more even, which lowers the corrosion current density to 199 μA/cm2 and reduces micro-galvanic effects at grain boundaries. These results show that adding Li can change the microstructure of solidification, which is a step toward producing high-performance biodegradable implants without any extra work.
- Open Access
- 22 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Mechanical, wear, and biocorrosion behavior of biodegradable Mg–3Zn–3Sn–xLi alloys: The synergistic role of Li addition and thermo-mechanical processing
- 22 May 2026
- Published by Elsevier in Results in Engineering
- Vol. 30
Open AccessMechanical, wear, and biocorrosion behavior of biodegradable Mg–3Zn–3Sn–xLi alloys: The synergistic role of Li addition and thermo-mechanical processing
- 11 May 2026
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 39 (3) , 88
Optimizing Bi2223 Superconductors with 2D Materials: rGO as the Superior Dopant
- 11 May 2026
- Published by Springer Nature in Journal of Superconductivity and Novel Magnetism
- Vol. 39 (3) , 88
Optimizing Bi2223 Superconductors with 2D Materials: rGO as the Superior Dopant
- Open Access
- 2 March 2026
- Published by Elsevier in SSRN Electronic Journal
Mechanical, wear, and biocorrosion behavior of biodegradable Mg–3Zn–3Sn–xLi alloys: The influence of different processing routes
Magnesium (Mg) alloys show promise as biodegradable orthopedic implants, but their rapid degradation is still a major clinical problem. This study examined the microstructural evolution and multifunctional performance of Mg–3Zn–3Sn (ZT33) and Mg–3Zn–3Sn–3Li (ZTL333) alloys subjected to casting, heat treatment, and hot extrusion. Rietveld refinement showed that adding lithium (Li) enhances the lattice structure and the crystallographic parameters, which helps make a stable solid solution. Hot extrusion caused full dynamic recrystallization, which changed coarse dendritic structures into a uniform microstructure with very fine grains. The extruded ZTL333 alloy had the best mechanical properties, wear resistance, and corrosion resistance under all conditions. The alloy reached a maximum hardness of 68.52 HV and a maximum compressive strength (UCS) of 417.26 ± 8.34 MPa, which is required for cortical bone applications. Electrochemical tests in Dulbecco's Modified Eagle Medium (DMEM) showed that the corrosion resistance was greatly improved. This improved performance was mainly due to the homogeneity of the microstructure and the formation of a protective surface film, rather than surface wettability. In contrast, microgalvanic corrosion was observed in the heat-treated alloys due to the presence of Li2Sn5 intermetallic phases. Also, a bioactive hydroxyapatite layer formed in the extruded ZTL333 alloy, which shows that it has a lot of potential for making bone-implant integration better. In general, this work shows that combining Li alloying with grain refinement could be a potential way to make high-performance biodegradable Mg implants for the next generation.
- 2 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMechanical, wear, and biocorrosion behavior of biodegradable Mg–3Zn–3Sn–xLi alloys: The influence of different processing routes
Magnesium (Mg) alloys show promise as biodegradable orthopedic implants, but their rapid degradation is still a major clinical problem. This study examined the microstructural evolution and multifunctional performance of Mg–3Zn–3Sn (ZT33) and Mg–3Zn–3Sn–3Li (ZTL333) alloys subjected to casting, heat treatment, and hot extrusion. Rietveld refinement showed that adding lithium (Li) enhances the lattice structure and the crystallographic parameters, which helps make a stable solid solution. Hot extrusion caused full dynamic recrystallization, which changed coarse dendritic structures into a uniform microstructure with very fine grains. The extruded ZTL333 alloy had the best mechanical properties, wear resistance, and corrosion resistance under all conditions. The alloy reached a maximum hardness of 68.52 HV and a maximum compressive strength (UCS) of 417.26 ± 8.34 MPa, which is required for cortical bone applications. Electrochemical tests in Dulbecco's Modified Eagle Medium (DMEM) showed that the corrosion resistance was greatly improved. This improved performance was mainly due to the homogeneity of the microstructure and the formation of a protective surface film, rather than surface wettability. In contrast, microgalvanic corrosion was observed in the heat-treated alloys due to the presence of Li2Sn5 intermetallic phases. Also, a bioactive hydroxyapatite layer formed in the extruded ZTL333 alloy, which shows that it has a lot of potential for making bone-implant integration better. In general, this work shows that combining Li alloying with grain refinement could be a potential way to make high-performance biodegradable Mg implants for the next generation.
- Open Access
- 16 December 2025
- Published by Elsevier in Results in Physics
- Vol. 80
Synthesis and structural characterization of Ni2 FeAl Heusler alloy–embedded mesoporous SiO2 nanocomposite
- 16 December 2025
- Published by Elsevier in Results in Physics
- Vol. 80
Open AccessSynthesis and structural characterization of Ni2 FeAl Heusler alloy–embedded mesoporous SiO2 nanocomposite
- Open Access
- 11 September 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Corrosion inhibition performance of carbon steel in sulfuric acid using gum arabic extract: experimental insights, DFT analysis, and molecular dynamics simulations
- 11 September 2025
- Published by Elsevier in Results in Engineering
- Vol. 28
Open AccessCorrosion inhibition performance of carbon steel in sulfuric acid using gum arabic extract: experimental insights, DFT analysis, and molecular dynamics simulations