Jose Baranda Ribeiro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jose Baranda Ribeiro has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
- Ricardo Mendes
Univ Coimbra, ADAI, LEDAP, Department of Mechanical Engineering, Rua Luís Reis Santos, 3030-788, Coimbra, Portugal, Portugal
27 shared publications - Igor Plaksin
ADAI-LAETA, Department of Mechanical Engineering, University of Coimbra, Rua Luís Reis Santos, 3030-788 Coimbra
11 shared publications - Jose Campos
ADAI‐Associação para o Desenvolvimento da Aerodinâmica Industrial and LEDAP‐Laboratório de Energética e Detónica, Departament of Mechanical Engineering, University of Coimbra, Rua Luís Reis Santos, 3030‐788 Coimbra, Portugal
9 shared publications - João S. Pereira
ADAI-LAETA, Department of Mechanical Engineering,University of Coimbra,Coimbra,Portugal, Portugal
9 shared publications - Adélio Rodrigues Gaspar
University of Coimbra
7 shared publications - Carlos Ferreira
University of Coimbra, ADAI-LAETA, Department of Mechanical Engineering, Portugal
6 shared publications
Latest Publications
- Open Access
Performance Improvement and Repowering Strategies for an Existing Sugarcane Cogeneration Plant: Energy, Exergy, Economic and Environmental Assessment
This study evaluates performance-improvement and repowering strategies for an existing sugarcane cogeneration plant in Espírito Santo, Brazil, using field data and thermodynamic simulations performed with Thermoflex and EES software. The current operating condition was adopted as the Base Case and compared with three progressively more intensive scenarios. Increasing steam generation from 75 to 110 t/h raised net electrical power from 10.800 to 18.633 MW, while the simulated condenser steam flow reached 41.3 t/h, slightly exceeding its 40 t/h nominal capacity. Operation at the nominal boiler capacity of 150 t/h increased net electrical power to 32.560 MW and required additional condensation capacity. A repowering configuration at the same steam-generation rate, but with higher steam pressure and temperature and reheating, further increased net electrical power to 38.304 MW and net electrical efficiency from 23.12% to 27.44%. Exergetic efficiency increased from 23.50% to 26.85%, while total combined exergy destruction and losses decreased from 147.698 to 140.554 MW. Specific direct CO2 emissions decreased from 2.962 to 1.468 tCO2/MWh between the Base Case and Scenario 3. The revised incremental economic assessment, based on 3300 operating hours per year, resulted in an NPV of US$6.88 million and a discounted payback of 0.67 years for the transition to Scenario 2, whereas the repowering investment resulted in an NPV of −US$27.44 million. The results distinguish capacity recovery from technological repowering and show that higher thermodynamic performance does not necessarily correspond to greater economic attractiveness.
Open AccessPerformance Improvement and Repowering Strategies for an Existing Sugarcane Cogeneration Plant: Energy, Exergy, Economic and Environmental Assessment
This study evaluates performance-improvement and repowering strategies for an existing sugarcane cogeneration plant in Espírito Santo, Brazil, using field data and thermodynamic simulations performed with Thermoflex and EES software. The current operating condition was adopted as the Base Case and compared with three progressively more intensive scenarios. Increasing steam generation from 75 to 110 t/h raised net electrical power from 10.800 to 18.633 MW, while the simulated condenser steam flow reached 41.3 t/h, slightly exceeding its 40 t/h nominal capacity. Operation at the nominal boiler capacity of 150 t/h increased net electrical power to 32.560 MW and required additional condensation capacity. A repowering configuration at the same steam-generation rate, but with higher steam pressure and temperature and reheating, further increased net electrical power to 38.304 MW and net electrical efficiency from 23.12% to 27.44%. Exergetic efficiency increased from 23.50% to 26.85%, while total combined exergy destruction and losses decreased from 147.698 to 140.554 MW. Specific direct CO2 emissions decreased from 2.962 to 1.468 tCO2/MWh between the Base Case and Scenario 3. The revised incremental economic assessment, based on 3300 operating hours per year, resulted in an NPV of US$6.88 million and a discounted payback of 0.67 years for the transition to Scenario 2, whereas the repowering investment resulted in an NPV of −US$27.44 million. The results distinguish capacity recovery from technological repowering and show that higher thermodynamic performance does not necessarily correspond to greater economic attractiveness.
- Open Access
- 14 October 2026
- Published by MDPI AG in Preprints.org
Biochar-Derived Materials for Catalytic CO2 Reduction and Emerging Integrated Capture-Conversion Systems
The increasing concentration of atmospheric CO2 has intensified the search for sustainable technologies capable of converting this greenhouse gas into valuable fuels and chemicals. Among the available approaches, thermocatalytic, photocatalytic, and electrochemical CO2 reduction have emerged as key strategies for carbon valorisation. In this regard, biochar-derived materials have recently attracted growing attention due to their renewable origin, tunable porosity, rich surface chemistry, and ability to support active catalytic sites. These properties enhance CO2 adsorption, activation, and charge-transfer processes, making biochar a promising platform across multiple CO2 reduction pathways. This review provides a critical overview of recent advances in thermocatalytic, photocatalytic, and electrochemical CO2 reduction using biochar-based materials, highlighting the relationship between material properties and catalytic performance. Particular attention is given to integrated capture-conversion systems, where biochar enables the coupling of CO2 adsorption and catalytic transformation within a single material architecture. Current challenges and future research directions are discussed to support the development of scalable biochar-based technologies for sustainable carbon utilisation.
- 14 October 2026
- Published by MDPI AG in Preprints.org
Open AccessBiochar-Derived Materials for Catalytic CO2 Reduction and Emerging Integrated Capture-Conversion Systems
The increasing concentration of atmospheric CO2 has intensified the search for sustainable technologies capable of converting this greenhouse gas into valuable fuels and chemicals. Among the available approaches, thermocatalytic, photocatalytic, and electrochemical CO2 reduction have emerged as key strategies for carbon valorisation. In this regard, biochar-derived materials have recently attracted growing attention due to their renewable origin, tunable porosity, rich surface chemistry, and ability to support active catalytic sites. These properties enhance CO2 adsorption, activation, and charge-transfer processes, making biochar a promising platform across multiple CO2 reduction pathways. This review provides a critical overview of recent advances in thermocatalytic, photocatalytic, and electrochemical CO2 reduction using biochar-based materials, highlighting the relationship between material properties and catalytic performance. Particular attention is given to integrated capture-conversion systems, where biochar enables the coupling of CO2 adsorption and catalytic transformation within a single material architecture. Current challenges and future research directions are discussed to support the development of scalable biochar-based technologies for sustainable carbon utilisation.
- Open Access
- 17 June 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 269
A closed-form homothetic model for the convective sublimation of dry ice
- 17 June 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 269
Open AccessA closed-form homothetic model for the convective sublimation of dry ice
- Open Access
- 27 April 2026
- Published by Elsevier in SSRN Electronic Journal
A Closed-Form Homothetic Model for the Convective Sublimation of Dry Ice
Dry ice sublimation governs mass loss, storage duration, and transport performance in carbon management and temperature-controlled applications. Existing predictive approaches are often computationally intensive or restricted to specific geometries and operating conditions of the system. In this study, we developed a closed-form analytical model for the time-dependent sublimation of solid CO2 under natural and forced convection. The formulation combines the interfacial energy balance, convective heat transfer scaling, and homothetic geometric retraction, yielding an explicit expression for the remaining solid mass in terms of the fluid properties, thermal driving potential, geometry, and initial conditions. The model is parameterized by the coefficient K_s and exponent γ, which are obtained from convection correlations and geometric scaling. Validation against independent experimental data from the literature showed good agreement for cylindrical pellets in low-velocity flow and dry-ice blocks under natural convection. Because maximizing the sublimation time is relevant to storage and transport, the design-oriented application of the model focused on natural convection. Under the examined conditions, the geometry that maximizes the sublimation time is governed by the competition between compactness and convective response, rather than by compactness alone. Therefore, the proposed model provides a simple and physically transparent framework for predicting dry-ice sublimation and comparing storage geometries.
- 27 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessA Closed-Form Homothetic Model for the Convective Sublimation of Dry Ice
Dry ice sublimation governs mass loss, storage duration, and transport performance in carbon management and temperature-controlled applications. Existing predictive approaches are often computationally intensive or restricted to specific geometries and operating conditions of the system. In this study, we developed a closed-form analytical model for the time-dependent sublimation of solid CO2 under natural and forced convection. The formulation combines the interfacial energy balance, convective heat transfer scaling, and homothetic geometric retraction, yielding an explicit expression for the remaining solid mass in terms of the fluid properties, thermal driving potential, geometry, and initial conditions. The model is parameterized by the coefficient K_s and exponent γ, which are obtained from convection correlations and geometric scaling. Validation against independent experimental data from the literature showed good agreement for cylindrical pellets in low-velocity flow and dry-ice blocks under natural convection. Because maximizing the sublimation time is relevant to storage and transport, the design-oriented application of the model focused on natural convection. Under the examined conditions, the geometry that maximizes the sublimation time is governed by the competition between compactness and convective response, rather than by compactness alone. Therefore, the proposed model provides a simple and physically transparent framework for predicting dry-ice sublimation and comparing storage geometries.
- Open Access
Thermodynamic Assessment of Heat Pump Configurations for Waste Heat Integrated Carnot Batteries
Carnot batteries based on the coupling of high-temperature heat pumps (HTHPs) and Organic Rankine Cycles (ORCs) emerge as promising solutions for large-scale and long-duration energy storage, enabling sector coupling and the valorization of industrial waste heat. In such systems, the charging subsystem plays a dominant role, as variations in heat pump performance influence the round-trip efficiency more strongly than comparable variations in the ORC. This work presents a thermodynamic assessment of Rankine-based HP–ORC Carnot batteries focusing on the influence of heat pump configuration and working fluid selection. System performance is evaluated using the heat pump coefficient of performance, volumetric heat capacity, ORC efficiency, and Carnot battery round-trip efficiency through a grid-search optimization over a wide range of storage outlet and waste heat source temperatures. The results show that single-stage configurations are optimal at low to moderate temperature lifts, while two-stage and cascade systems become advantageous at higher lifts. Among the investigated fluids, R-601 provides the highest round-trip efficiencies at elevated storage temperatures, whereas R-600 enables more compact systems due to its higher volumetric heat capacity. These findings provide design guidance for selecting heat pump configurations and working fluids in industrial waste-heat-assisted Carnot battery applications.
Open AccessThermodynamic Assessment of Heat Pump Configurations for Waste Heat Integrated Carnot Batteries
Carnot batteries based on the coupling of high-temperature heat pumps (HTHPs) and Organic Rankine Cycles (ORCs) emerge as promising solutions for large-scale and long-duration energy storage, enabling sector coupling and the valorization of industrial waste heat. In such systems, the charging subsystem plays a dominant role, as variations in heat pump performance influence the round-trip efficiency more strongly than comparable variations in the ORC. This work presents a thermodynamic assessment of Rankine-based HP–ORC Carnot batteries focusing on the influence of heat pump configuration and working fluid selection. System performance is evaluated using the heat pump coefficient of performance, volumetric heat capacity, ORC efficiency, and Carnot battery round-trip efficiency through a grid-search optimization over a wide range of storage outlet and waste heat source temperatures. The results show that single-stage configurations are optimal at low to moderate temperature lifts, while two-stage and cascade systems become advantageous at higher lifts. Among the investigated fluids, R-601 provides the highest round-trip efficiencies at elevated storage temperatures, whereas R-600 enables more compact systems due to its higher volumetric heat capacity. These findings provide design guidance for selecting heat pump configurations and working fluids in industrial waste-heat-assisted Carnot battery applications.
- Open Access
Assessment of the Portuguese Forest Potential for Biogenic Carbon Production and Global Research Trends
Forests play a central role in climate change mitigation by acting as biogenic carbon reservoirs and providing renewable biomass for energy systems. In Portugal, where fire-prone landscapes and species composition dynamics pose increasing management challenges, understanding the carbon storage potential of forest biomass is crucial for designing effective decarbonization strategies. This study provides a comprehensive characterization of the Portuguese forest and quantifies the biogenic carbon stored in live and dead biomass across the main forest species. Species-specific carbon contents, rather than the conventional 50% assumption widely used in the literature, were applied to National Forest Inventory data, enabling more realistic and representative carbon stock estimates expressed in kilotonnes of CO2 equivalent. While the approach relies on inventory-based biomass data and literature-derived carbon fractions and is therefore subject to associated uncertainties, it provides an improved representation of species-level carbon storage at the national scale. Results show that Pinus pinaster, Eucalyptus globulus, and Quercus suber together represent the largest share of carbon storage, with approximately 300,000 kilotonnes of CO2 equivalent retained in living trees. Wood is the dominant carbon pool, but roots and branches also account for a substantial fraction, emphasizing the need to consider both above- and below-ground biomass in carbon accounting. In parallel, a bibliometric analysis based on the systematic evaluation of scientific publications was conducted to characterize the evolution, thematic focus, and geographic distribution of global research on forest-based biogenic carbon. This analysis reveals a rapidly expanding scientific interest in biogenic carbon, particularly since 2020, reflecting its growing relevance in climate change mitigation frameworks. Overall, the results underscore both the strategic importance of Portuguese forests and the alignment of this research with the broader international scientific agenda on forest-based biogenic carbon.
Open AccessAssessment of the Portuguese Forest Potential for Biogenic Carbon Production and Global Research Trends
Forests play a central role in climate change mitigation by acting as biogenic carbon reservoirs and providing renewable biomass for energy systems. In Portugal, where fire-prone landscapes and species composition dynamics pose increasing management challenges, understanding the carbon storage potential of forest biomass is crucial for designing effective decarbonization strategies. This study provides a comprehensive characterization of the Portuguese forest and quantifies the biogenic carbon stored in live and dead biomass across the main forest species. Species-specific carbon contents, rather than the conventional 50% assumption widely used in the literature, were applied to National Forest Inventory data, enabling more realistic and representative carbon stock estimates expressed in kilotonnes of CO2 equivalent. While the approach relies on inventory-based biomass data and literature-derived carbon fractions and is therefore subject to associated uncertainties, it provides an improved representation of species-level carbon storage at the national scale. Results show that Pinus pinaster, Eucalyptus globulus, and Quercus suber together represent the largest share of carbon storage, with approximately 300,000 kilotonnes of CO2 equivalent retained in living trees. Wood is the dominant carbon pool, but roots and branches also account for a substantial fraction, emphasizing the need to consider both above- and below-ground biomass in carbon accounting. In parallel, a bibliometric analysis based on the systematic evaluation of scientific publications was conducted to characterize the evolution, thematic focus, and geographic distribution of global research on forest-based biogenic carbon. This analysis reveals a rapidly expanding scientific interest in biogenic carbon, particularly since 2020, reflecting its growing relevance in climate change mitigation frameworks. Overall, the results underscore both the strategic importance of Portuguese forests and the alignment of this research with the broader international scientific agenda on forest-based biogenic carbon.
- 17 April 2025
- Published by Springer Nature
- p. 127-141
Development of a Novel Off-grid Power Module for Forest Machines Based on Rankine Technology
- 17 April 2025
- Published by Springer Nature
- p. 127-141
Development of a Novel Off-grid Power Module for Forest Machines Based on Rankine Technology
- Open Access
Optimization of ORC-Based Micro-CHP Systems: An Experimental and Control-Oriented Study
This study presents an experimental and numerical investigation into the performance and control optimization of an Organic Rankine Cycle (ORC)-based micro-combined heat and power (micro-CHP) system. A steady-state, off-design, charge-sensitive model is developed to design a control strategy for an ORC micro-CHP combi-boiler, aiming to efficiently meet real-time domestic hot water demands (up to 40 °C and 35 kW) while generating up to 2 kW of electricity. The system utilizes a natural gas burner to evaporate the working fluid (R245fa), with combustion heat power, volumetric pump speed, and expander speed as control variables. Experimental and numerical evaluations generate steady-state control maps to identify optimal operating regions. A PID-based dynamic control strategy is then developed to stabilize operation during start-ups and user demand variations. The results confirm that the strategy delivers hot water within 1.5 min in simple boiler mode and 3 min in cogeneration mode while improving electricity generation stability and outperforming manual control. The findings demonstrate that integrating steady-state modeling with optimized control enhances the performance, responsiveness, and efficiency of ORC-based micro-CHP systems, making them a viable alternative for residential energy solutions.
Open AccessOptimization of ORC-Based Micro-CHP Systems: An Experimental and Control-Oriented Study
This study presents an experimental and numerical investigation into the performance and control optimization of an Organic Rankine Cycle (ORC)-based micro-combined heat and power (micro-CHP) system. A steady-state, off-design, charge-sensitive model is developed to design a control strategy for an ORC micro-CHP combi-boiler, aiming to efficiently meet real-time domestic hot water demands (up to 40 °C and 35 kW) while generating up to 2 kW of electricity. The system utilizes a natural gas burner to evaporate the working fluid (R245fa), with combustion heat power, volumetric pump speed, and expander speed as control variables. Experimental and numerical evaluations generate steady-state control maps to identify optimal operating regions. A PID-based dynamic control strategy is then developed to stabilize operation during start-ups and user demand variations. The results confirm that the strategy delivers hot water within 1.5 min in simple boiler mode and 3 min in cogeneration mode while improving electricity generation stability and outperforming manual control. The findings demonstrate that integrating steady-state modeling with optimized control enhances the performance, responsiveness, and efficiency of ORC-based micro-CHP systems, making them a viable alternative for residential energy solutions.
- Open Access
- 10 May 2024
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 23
Performance evaluation of PID and Fuzzy Logic controllers for residential ORC-based cogeneration systems
- 10 May 2024
- Published by Elsevier in Energy Conversion and Management: X
- Vol. 23
Open AccessPerformance evaluation of PID and Fuzzy Logic controllers for residential ORC-based cogeneration systems
- 23 May 2023
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 48 (8)
Detonation characterization of low‐density emulsion explosives
Due to the wide applicability and popularity of emulsion explosives (EEs) in the industry, ongoing advancements have been made in order to better understand and optimize the capabilities of EEs. Over the recent years, work has been developed to understand the effect that additives have on the detonation phenomena, and the energetic properties of EEs. In recent studies, most emphasis has been given to energetic additives, and little information is available regarding non‐energetic additives, despite their rising use in industrial applications. This work intends to do a detonation characterization of low‐density EEs, using EPS as a non‐energetic additive, in a concentration range of 0 % to 4 %, and consequently, an EEs density range of 1.12 g/cm3 down to 0.49 g/cm3. In order to characterize the detonation velocity and pressure of these EEs, different charge configurations (rectangular cross‐section and cylindrical) and measurement methods (discrete and quasi‐continuous) were used throughout this work. The results obtained, for these charge configurations and within EEs with these compositions and densities, display a linear behaviour for the detonation velocity, ranging from 2126 m/s up to 5581 m/s, and also for the values of the detonation pressure, varying between 3.3 GPa up to 11.7 GPa.
- 23 May 2023
- Published by Wiley in Propellants, Explosives, Pyrotechnics
- Vol. 48 (8)
Detonation characterization of low‐density emulsion explosives
Due to the wide applicability and popularity of emulsion explosives (EEs) in the industry, ongoing advancements have been made in order to better understand and optimize the capabilities of EEs. Over the recent years, work has been developed to understand the effect that additives have on the detonation phenomena, and the energetic properties of EEs. In recent studies, most emphasis has been given to energetic additives, and little information is available regarding non‐energetic additives, despite their rising use in industrial applications. This work intends to do a detonation characterization of low‐density EEs, using EPS as a non‐energetic additive, in a concentration range of 0 % to 4 %, and consequently, an EEs density range of 1.12 g/cm3 down to 0.49 g/cm3. In order to characterize the detonation velocity and pressure of these EEs, different charge configurations (rectangular cross‐section and cylindrical) and measurement methods (discrete and quasi‐continuous) were used throughout this work. The results obtained, for these charge configurations and within EEs with these compositions and densities, display a linear behaviour for the detonation velocity, ranging from 2126 m/s up to 5581 m/s, and also for the values of the detonation pressure, varying between 3.3 GPa up to 11.7 GPa.