Jörg Lüchtenborg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Jörg Lüchtenborg has a total of 69 co-authors. Here are the top co-authors by number of shared publications:
- Benedikt Christopher Spies
Department of Prosthetic Dentistry, Center for Dental Medicine, Medical Center-University of Freiburg, Faculty of Medicine, University of Freiburg, Freiburg, Germany
9 shared publications - Brigitte Altmann
Department of Prosthetic Dentistry, Center for Dental Medicine, Medical Center - University of Freiburg, Faculty of Medicine, University of Freiburg, Hugstetterstr. 55, 79106 Freiburg, Germany; G.E.R.N Research Center for Tissue Replacement, Regeneration & Neogenesis, Department of Prosthetic Dentistry, Center for Dental Medicine, Medical Center - University of Freiburg, Faculty of Medicine, University of Freiburg, Engesserstr. 4, 79108 Freiburg, Germany
3 shared publications - Felix Burkhardt
Medical Center - University of Freiburg, Center for Dental Medicine, Department of Prosthetic Dentistry, Faculty of Medicine, University of Freiburg, Hugstetter Str. 55, 79106 Freiburg, Germany
3 shared publications - Kirstin Vach
Center for Data Science, Eberswalde University for Sustainable Development, Schicklerstr. 5, 16225 Eberswalde, Germany
3 shared publications Severin Rothlauf
Center for Dental Medicine Department of Prosthetic Dentistry Faculty of Medicine University of Freiburg Freiburg Germany
3 shared publications- Ahmad Amro Baradee
Department of Prosthetic Dentistry, Faculty of Medicine, Medical Center -University of Freiburg, Center for Dental Medicine, University of Freiburg, Hugstetter Str. 55, Freiburg, 79106, Germany
2 shared publications
Latest Publications
- Open Access
- 24 October 2026
- Published by Elsevier in Journal of Dentistry
- Vol. 177
Clinical evaluation of 3D-printed stabilization splints for probable bruxism: An exploratory cohort analysis of a randomized prospective single-blinded crossover trial
- 24 October 2026
- Published by Elsevier in Journal of Dentistry
- Vol. 177
Open AccessClinical evaluation of 3D-printed stabilization splints for probable bruxism: An exploratory cohort analysis of a randomized prospective single-blinded crossover trial
- Open Access
- 13 July 2026
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 182, 107556
Comparing the load-bearing capacity of 3D printed and CAD/CAM milled 3Y-TZP bridges after artificial ageing
- 13 July 2026
- Published by Elsevier in Journal of the Mechanical Behavior of Biomedical Materials
- Vol. 182, 107556
Open AccessComparing the load-bearing capacity of 3D printed and CAD/CAM milled 3Y-TZP bridges after artificial ageing
- Open Access
- 3 June 2026
- Published by Elsevier in Dental Materials
- Vol. 42 (11) , 2077-2085
Optical properties and long-term aging under simulated oral conditions of monolithic four-unit fixed dental prostheses manufactured from gelcast zirconia discs
- 3 June 2026
- Published by Elsevier in Dental Materials
- Vol. 42 (11) , 2077-2085
Open AccessOptical properties and long-term aging under simulated oral conditions of monolithic four-unit fixed dental prostheses manufactured from gelcast zirconia discs
- Open Access
- 11 May 2026
- Published by Elsevier in Dental Materials
- Vol. 42 (10) , 1860-1866
An in vitro analysis of two-body wear and three body wear, hardness, and degree of conversion of 3D-printed restorative materials
- 11 May 2026
- Published by Elsevier in Dental Materials
- Vol. 42 (10) , 1860-1866
Open AccessAn in vitro analysis of two-body wear and three body wear, hardness, and degree of conversion of 3D-printed restorative materials
- Open Access
- 6 August 2025
- Published by Elsevier in Acta Biomaterialia
- Vol. 204, 312-322
Dynamic release kinetics and biological impact of leachables from 3D-printed oral devices: An integrated in vitro and computational exposure model
- 6 August 2025
- Published by Elsevier in Acta Biomaterialia
- Vol. 204, 312-322
Open AccessDynamic release kinetics and biological impact of leachables from 3D-printed oral devices: An integrated in vitro and computational exposure model
- Open Access
- 24 July 2025
- Published by Wiley in Journal of Prosthodontics
Impact of monomer contamination of isopropanol during post‐rinsing on the accuracy of dental models fabricated by vat photopolymerization
Purpose: The aim of this study was to investigate the impact of an increasing level of monomer contamination of isopropanol (isopropyl alcohol [IPA]) during post‐rinsing on the dimensional stability of test samples produced by vat photopolymerization. The effect of resin deposits due to insufficient post‐rinsing on the accuracy (volume, mean, and maximum deviation) of additive manufacturing workflows was investigated, which has received limited attention in studies on accuracy.Materials and Methods: Forty test specimens (four groups, n = 10) were produced from a commonly used resin for dental model fabrication and underwent post‐rinsing in IPA with different levels of monomer contamination (0, 10, 20, and 30 wt%). The dimensional stability was assessed by comparing the optical scan of the produced test specimens with the original digital design. Both the volume of the deposited resin and the effect of different model shapes (inner edges, smooth surfaces, and outer edges) on deposition were investigated. Statistical evaluation was performed using the Kruskal–Wallis test and Dunn's test for pairwise comparisons with Holm correction. To simulate clinical conditions, 20 dental models (four groups, n = 5) were produced, post‐processed, and examined using a scanning method.Results: No significant deviations in specimen dimensions occurred when the monomer contamination was 0%–10%. In the range of 10%–20% contamination, a few significant deviations occurred in the area of sharp inner edges, “inside structures” and small structures (diameter 20%. At contamination levels of 10%–20%, post‐rinsing of components with large smooth surfaces without sharp edges (e.g., custom trays) is possible without significant deformation. Only for components with very small, sharp‐edged, or inverted structures is it advisable to replace the IPA from a contamination level of 10%.
- 24 July 2025
- Published by Wiley in Journal of Prosthodontics
Open AccessImpact of monomer contamination of isopropanol during post‐rinsing on the accuracy of dental models fabricated by vat photopolymerization
Purpose: The aim of this study was to investigate the impact of an increasing level of monomer contamination of isopropanol (isopropyl alcohol [IPA]) during post‐rinsing on the dimensional stability of test samples produced by vat photopolymerization. The effect of resin deposits due to insufficient post‐rinsing on the accuracy (volume, mean, and maximum deviation) of additive manufacturing workflows was investigated, which has received limited attention in studies on accuracy.Materials and Methods: Forty test specimens (four groups, n = 10) were produced from a commonly used resin for dental model fabrication and underwent post‐rinsing in IPA with different levels of monomer contamination (0, 10, 20, and 30 wt%). The dimensional stability was assessed by comparing the optical scan of the produced test specimens with the original digital design. Both the volume of the deposited resin and the effect of different model shapes (inner edges, smooth surfaces, and outer edges) on deposition were investigated. Statistical evaluation was performed using the Kruskal–Wallis test and Dunn's test for pairwise comparisons with Holm correction. To simulate clinical conditions, 20 dental models (four groups, n = 5) were produced, post‐processed, and examined using a scanning method.Results: No significant deviations in specimen dimensions occurred when the monomer contamination was 0%–10%. In the range of 10%–20% contamination, a few significant deviations occurred in the area of sharp inner edges, “inside structures” and small structures (diameter 20%. At contamination levels of 10%–20%, post‐rinsing of components with large smooth surfaces without sharp edges (e.g., custom trays) is possible without significant deformation. Only for components with very small, sharp‐edged, or inverted structures is it advisable to replace the IPA from a contamination level of 10%.
- 27 May 2025
- Published by Elsevier in Journal of Dentistry
- Vol. 160, 105855
Evaluation of microbial adhesion on 3D-printed zirconia surfaces: Effects of printing angle and layer thickness
- 27 May 2025
- Published by Elsevier in Journal of Dentistry
- Vol. 160, 105855
Evaluation of microbial adhesion on 3D-printed zirconia surfaces: Effects of printing angle and layer thickness
- Open Access
- 20 May 2025
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 134 (3) , 842.e1-842.e11
Influence of pretreatment strategies on the tensile bond strength of 3D printed composite resins for definitive cementation to dentin
- 20 May 2025
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 134 (3) , 842.e1-842.e11
Open AccessInfluence of pretreatment strategies on the tensile bond strength of 3D printed composite resins for definitive cementation to dentin
- Open Access
- 5 April 2025
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 134 (1) , 229.e1-229.e7
Influence of 3D printed and milled zirconia on the adhesion and viability of keratinocytes: An in vitro study
- 5 April 2025
- Published by Elsevier in The Journal of Prosthetic Dentistry
- Vol. 134 (1) , 229.e1-229.e7
Open AccessInfluence of 3D printed and milled zirconia on the adhesion and viability of keratinocytes: An in vitro study
- Open Access
- 1 April 2025
- Published by Elsevier in Dental Materials
- Vol. 41 (6) , 631-643
Identification of a surface texture parameter panel characterizing surface micromorphologies of differently processed oral implant surfaces
- 1 April 2025
- Published by Elsevier in Dental Materials
- Vol. 41 (6) , 631-643
Open AccessIdentification of a surface texture parameter panel characterizing surface micromorphologies of differently processed oral implant surfaces