Loizos Efthymiou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Loizos Efthymiou has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Giorgia Longobardi
University of Cambridge,Department of Engineering,Cambridge,UK
3 shared publications Florin Udrea
Electrical Engineering Department, University of Cambridge, Cambridgeshire, UK
2 shared publications- Florin Udrea
University of Cambridge
2 shared publications - Karthick Murukesan
Electrical Engineering Department, University of Cambridge, Cambridge CB3 0FA, UK
2 shared publications Ayman Shibib
Vishay Siliconix, San Jose, CA, USA
1 shared publicationF. Udrea
University of Cambridge 1 Department of Electrical Engineering Cambridge CB3 0FA, United Kingdom
1 shared publication
Latest Publications
- Open Access
- 10 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 831-838
On the Challenges of Reliable Threshold Voltage Measurement in Ohmic and Schottky Gate p-GaN HEMTs
For large scale testability of p-GaN HEMTs it is essential to investigate threshold voltage (Vth) instability from the perspective of the measurement induced instability. In this paper the impact of accumulated gate bias stress during standard transfer characteristic measurements (ID-VG) in a p-GaN AlGaN/GaN-on-Si normally off HEMT is quantitatively analysed and modelled. This illustrates the associated threshold voltage (Vth) instabilities and leads to a better understanding of the Vth measurement challenges of a p-GaN HEMT. Upon an application of a constant gate bias close to nominal Vth the drain current ID shows an initial marginal rise, followed by a short stable period (IDstable-Tzone) and a steep decay period. The effective bias history built on the gate stack varies when pulse on-time (Ton) or step time (Tstep), corresponding to pulsed or DC step ID-VG measurements, are varied. We find that this can lead to a Vth variation of up to 20%. It is also observed that the choice of Ton and Tstep determines whether ID is measured in IDstable-Tzone or the rise or decay periods. Measurement induced Vth instability is attributed to trapping of 2DEG electrons at the AlGaN barrier and we demonstrate that an ohmic gate contact, in comparison to the Schottky gate contact, may compensate for the trapped 2DEG electrons by hole injection across the AlGaN barrier. Experimental results of Vth stability under the same stress conditions for a Schottky and ohmic gate contact are supported by a detailed TCAD analysis.
- 10 September 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. 9, 831-838
Open AccessOn the Challenges of Reliable Threshold Voltage Measurement in Ohmic and Schottky Gate p-GaN HEMTs
For large scale testability of p-GaN HEMTs it is essential to investigate threshold voltage (Vth) instability from the perspective of the measurement induced instability. In this paper the impact of accumulated gate bias stress during standard transfer characteristic measurements (ID-VG) in a p-GaN AlGaN/GaN-on-Si normally off HEMT is quantitatively analysed and modelled. This illustrates the associated threshold voltage (Vth) instabilities and leads to a better understanding of the Vth measurement challenges of a p-GaN HEMT. Upon an application of a constant gate bias close to nominal Vth the drain current ID shows an initial marginal rise, followed by a short stable period (IDstable-Tzone) and a steep decay period. The effective bias history built on the gate stack varies when pulse on-time (Ton) or step time (Tstep), corresponding to pulsed or DC step ID-VG measurements, are varied. We find that this can lead to a Vth variation of up to 20%. It is also observed that the choice of Ton and Tstep determines whether ID is measured in IDstable-Tzone or the rise or decay periods. Measurement induced Vth instability is attributed to trapping of 2DEG electrons at the AlGaN barrier and we demonstrate that an ohmic gate contact, in comparison to the Schottky gate contact, may compensate for the trapped 2DEG electrons by hole injection across the AlGaN barrier. Experimental results of Vth stability under the same stress conditions for a Schottky and ohmic gate contact are supported by a detailed TCAD analysis.
- Top Cited Papers
- 28 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 40 (8) , 1253-1256
Understanding the Threshold Voltage Instability During OFF-State Stress in p-GaN HEMTs
In this letter we investigate by means of experimental results and TCAD simulations the threshold voltage instability due to off-state drain stress in p-GaN gate AlGaN/GaN-on-Si HEMTs. When the drain of the p-GaN HEMT is biased in the off-state the threshold voltage (Vth) shows a linear increase up to ∼ 40%. This increase saturates at drain bias voltages above 50V. The positive Vth shift is attributed to the ionization of acceptor traps in the AlGaN region below the p-GaN gate with the source of these trapping sites suggested to be the p-GaN gate out-diffused Mg dopant atoms. The ionization of the Mg acceptors due to high electric field during off-state bias and the removal of the generated holes from the AlGaN region through the gate contact creates the charge conditions for a positive Vth shift. The sharp decrease in the gate drain capacitance (Cgd) for VD < 50V, the simulated gate edge electric field reaching its peak for a drain voltage bias VD ∼ 50V and the positive threshold voltage shift observed for negative gate stress further validate the proposed model.
- 28 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 40 (8) , 1253-1256
Top Cited PapersUnderstanding the Threshold Voltage Instability During OFF-State Stress in p-GaN HEMTs
In this letter we investigate by means of experimental results and TCAD simulations the threshold voltage instability due to off-state drain stress in p-GaN gate AlGaN/GaN-on-Si HEMTs. When the drain of the p-GaN HEMT is biased in the off-state the threshold voltage (Vth) shows a linear increase up to ∼ 40%. This increase saturates at drain bias voltages above 50V. The positive Vth shift is attributed to the ionization of acceptor traps in the AlGaN region below the p-GaN gate with the source of these trapping sites suggested to be the p-GaN gate out-diffused Mg dopant atoms. The ionization of the Mg acceptors due to high electric field during off-state bias and the removal of the generated holes from the AlGaN region through the gate contact creates the charge conditions for a positive Vth shift. The sharp decrease in the gate drain capacitance (Cgd) for VD < 50V, the simulated gate edge electric field reaching its peak for a drain voltage bias VD ∼ 50V and the positive threshold voltage shift observed for negative gate stress further validate the proposed model.
- 25 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (5) , 2301-2306
Bonding Pad Over Active Area Layout for Lateral AlGaN/GaN Power HEMTs: A Critical View
This paper investigates the advantages and disadvantages of bonding pad over active area (BPOA) layout over a conventional layout for lateral AlGaN/GaN HEMTs designed for use in power applications. Extensive analysis of the performance of a BPOA device, both experimentally and supported by 3-D TCAD model simulations, reveals that while it can offer a higher current capability per unit area, it can lead to other disadvantages compared to a conventional design when considering reliability aspects.
- 25 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 66 (5) , 2301-2306
Bonding Pad Over Active Area Layout for Lateral AlGaN/GaN Power HEMTs: A Critical View
This paper investigates the advantages and disadvantages of bonding pad over active area (BPOA) layout over a conventional layout for lateral AlGaN/GaN HEMTs designed for use in power applications. Extensive analysis of the performance of a BPOA device, both experimentally and supported by 3-D TCAD model simulations, reveals that while it can offer a higher current capability per unit area, it can lead to other disadvantages compared to a conventional design when considering reliability aspects.
- Open Access
On the Source of Oscillatory Behaviour during Switching of Power Enhancement Mode GaN HEMTs
With Gallium Nitride (GaN) device technology for power electronics applications being ramped up for volume production, an increasing amount of research is now focused on the performance of GaN power devices in circuits. In this study, an enhancement mode GaN high electron mobility transistor (HEMT) is switched in a clamped inductive switching configuration with the aim of investigating the source of oscillatory effects observed. These arise as a result of the increased switching speed capability of GaN devices compared to their silicon counterparts. The study identifies the two major mechanisms (Miller capacitance charge and parasitic common source inductance) that can lead to ringing behaviour during turn-off and considers the effect of temperature on the latter. Furthermore, the experimental results are backed by SPICE modelling to evaluate the contribution of different circuit components to oscillations. The study concludes with good design techniques that can suppress the effects discussed.
Open AccessOn the Source of Oscillatory Behaviour during Switching of Power Enhancement Mode GaN HEMTs
With Gallium Nitride (GaN) device technology for power electronics applications being ramped up for volume production, an increasing amount of research is now focused on the performance of GaN power devices in circuits. In this study, an enhancement mode GaN high electron mobility transistor (HEMT) is switched in a clamped inductive switching configuration with the aim of investigating the source of oscillatory effects observed. These arise as a result of the increased switching speed capability of GaN devices compared to their silicon counterparts. The study identifies the two major mechanisms (Miller capacitance charge and parasitic common source inductance) that can lead to ringing behaviour during turn-off and considers the effect of temperature on the latter. Furthermore, the experimental results are backed by SPICE modelling to evaluate the contribution of different circuit components to oscillations. The study concludes with good design techniques that can suppress the effects discussed.
- Top Cited Papers
- 20 March 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (12)
On the physical operation and optimization of the p-GaN gate in normally-off GaN HEMT devices
In this study, an investigation is undertaken to determine the effect of gate design parameters on the on-state characteristics (threshold voltage and gate turn-on voltage) of pGaN/AlGaN/GaN high electron mobility transistors (HEMTs). Design parameters considered are pGaN doping and gate metal work function. The analysis considers the effects of variations on these parameters using a TCAD model matched with experimental results. A better understanding of the underlying physics governing the operation of these devices is achieved with a view to enable better optimization of such gate designs.
- 20 March 2017
- Published by AIP Publishing in Applied Physics Letters
- Vol. 110 (12)
Top Cited PapersOn the physical operation and optimization of the p-GaN gate in normally-off GaN HEMT devices
In this study, an investigation is undertaken to determine the effect of gate design parameters on the on-state characteristics (threshold voltage and gate turn-on voltage) of pGaN/AlGaN/GaN high electron mobility transistors (HEMTs). Design parameters considered are pGaN doping and gate metal work function. The analysis considers the effects of variations on these parameters using a TCAD model matched with experimental results. A better understanding of the underlying physics governing the operation of these devices is achieved with a view to enable better optimization of such gate designs.