Hiroki Nagai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hiroki Nagai has a total of 91 co-authors. Here are the top co-authors by number of shared publications:
- Tsubasa Ikami
Institute of Fluid Science, Tohoku University 1 , 2-1-1 Katahira, Aoba, Sendai, Miyagi 980-8577
19 shared publications - Yasuhiro Egami
Aichi Institute of Technology
10 shared publications - Koji Fujita
Institute of Fluid Science, Tohoku University, Sendai 980-8577, Japan
8 shared publications - Tomoki Inoue
Department of Modern Mechanical Engineering, Waseda University, 3-4-1 Ookubo, Shinjuku-ku, Tokyo 169-8555, Japan
7 shared publications - Takurou Daimaru
Tohoku University
6 shared publications - Yu Matsuda
Department of Modern Mechanical Engineering, Waseda University, 3-4-1 Ookubo, Shinjuku-ku, Tokyo 169-8555, Japan
6 shared publications
Latest Publications
- Open Access
- 3 August 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 179
Unsteady aerodynamic characteristics of a high-performance pitching airfoil under light dynamic stall at low reynolds number
- 3 August 2026
- Published by Elsevier in Aerospace Science and Technology
- Vol. 179
Open AccessUnsteady aerodynamic characteristics of a high-performance pitching airfoil under light dynamic stall at low reynolds number
- Open Access
- 1 August 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (8)
Data-driven unsteady entire flow field estimation using time-series multiple-field-of-view particle image velocimetry data
High-resolution flow field measurements often face a trade-off between spatial resolution and field of view (FOV) size, particularly in particle image velocimetry (PIV). To address this issue, we propose a data-driven method for reconstructing temporally consistent entire flow fields from time-series multi-FOV data acquired independently using a single camera. The method uses reduced-order modeling and sparse sensing to estimate time-varying coefficients of the proper orthogonal decomposition modes by minimizing discrepancies in overlapping regions between adjacent FOVs. The sparse sensor placement is optimized using a greedy algorithm, and the reconstruction problem is solved as a linear regression problem. The proposed method was validated using both simulated benchmark data and experimental PIV data obtained around a flat-plate airfoil. Results demonstrate that the proposed method accurately reconstructs unsteady flow structures, including vortex shedding and separation phenomena, with a normalized estimation error of approximately 0.17 when sufficient sensors are deployed. Moreover, the sensor distributions, which are concentrated in highly varying regions, indicate effective feature capture. This proposed method enables high-resolution observation of unsteady aerodynamic phenomena with minimal hardware.
- 1 August 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (8)
Open AccessData-driven unsteady entire flow field estimation using time-series multiple-field-of-view particle image velocimetry data
High-resolution flow field measurements often face a trade-off between spatial resolution and field of view (FOV) size, particularly in particle image velocimetry (PIV). To address this issue, we propose a data-driven method for reconstructing temporally consistent entire flow fields from time-series multi-FOV data acquired independently using a single camera. The method uses reduced-order modeling and sparse sensing to estimate time-varying coefficients of the proper orthogonal decomposition modes by minimizing discrepancies in overlapping regions between adjacent FOVs. The sparse sensor placement is optimized using a greedy algorithm, and the reconstruction problem is solved as a linear regression problem. The proposed method was validated using both simulated benchmark data and experimental PIV data obtained around a flat-plate airfoil. Results demonstrate that the proposed method accurately reconstructs unsteady flow structures, including vortex shedding and separation phenomena, with a normalized estimation error of approximately 0.17 when sufficient sensors are deployed. Moreover, the sensor distributions, which are concentrated in highly varying regions, indicate effective feature capture. This proposed method enables high-resolution observation of unsteady aerodynamic phenomena with minimal hardware.
- Open Access
- 31 July 2026
- Published by Springer Nature in Experiments in Fluids
- Vol. 67 (9) , 127
Particle-enhanced temperature-sensitive paint: development and validation for high-speed aerothermodynamic testing
Accurate surface temperature and heat flux measurements are essential for evaluating aerothermal loads on high-speed vehicles, including atmospheric entry capsules and space exploration vehicles. Temperature-sensitive paint provides a non-intrusive approach for global heat flux measurement in impulse ground-testing facilities, but its application is often limited by low signal levels caused by short test durations, high-frame-rate imaging, and the associated short exposure times. In this study, a particle-enhanced temperature-sensitive paint was developed and optimized by incorporating calcium silicate microparticles to improve luminescence output and measurement precision. Characterization tests showed that the optimized formulation increased emission intensity by 21% and temperature sensitivity by 11% relative to the reference temperature-sensitive paint, while retaining nearly twice the normalized emission intensity at 500 kPa. Shock tube validation demonstrated that the enhanced signal level reduced the standard deviation of reconstructed heat flux measurements by up to 33% under short-duration transient conditions, indicating the potential applicability of the particle-enhanced formulation for high-speed aerothermodynamic diagnostics.
- 31 July 2026
- Published by Springer Nature in Experiments in Fluids
- Vol. 67 (9) , 127
Open AccessParticle-enhanced temperature-sensitive paint: development and validation for high-speed aerothermodynamic testing
Accurate surface temperature and heat flux measurements are essential for evaluating aerothermal loads on high-speed vehicles, including atmospheric entry capsules and space exploration vehicles. Temperature-sensitive paint provides a non-intrusive approach for global heat flux measurement in impulse ground-testing facilities, but its application is often limited by low signal levels caused by short test durations, high-frame-rate imaging, and the associated short exposure times. In this study, a particle-enhanced temperature-sensitive paint was developed and optimized by incorporating calcium silicate microparticles to improve luminescence output and measurement precision. Characterization tests showed that the optimized formulation increased emission intensity by 21% and temperature sensitivity by 11% relative to the reference temperature-sensitive paint, while retaining nearly twice the normalized emission intensity at 500 kPa. Shock tube validation demonstrated that the enhanced signal level reduced the standard deviation of reconstructed heat flux measurements by up to 33% under short-duration transient conditions, indicating the potential applicability of the particle-enhanced formulation for high-speed aerothermodynamic diagnostics.
- Open Access
- 22 January 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 259
System-wide spacecraft temperature estimation using graph neural networks
- 22 January 2026
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 259
Open AccessSystem-wide spacecraft temperature estimation using graph neural networks
- Open Access
- 1 January 2026
- Published by Japan Society for Aeronautical and Space Sciences in TRANSACTIONS OF THE JAPAN SOCIETY FOR AERONAUTICAL AND SPACE SCIENCES
- Vol. 69 (6) , 177-185
Negatively Coned Blades for Reducing the Pitching Moment of Small Rotors in Forward Flight
This study introduces a novel design approach that incorporates a negative coning angle for the rotor blade to reduce rotor pitching moment in forward flight for small fixed-pitch rotors. This approach modifies the lift distribution on the rotor disk to reduce the nose-up pitching moment in forward flight. The effect of the negative coning angle on the pitching moment was studied using numerical simulations and wind tunnel experiments. Computational fluid dynamics simulations conducted without a turbulence model as a preliminary analysis predicted a reduction in pitching moment when a negative coning angle was adopted. Correspondingly, wind tunnel experiments indicated that a coning angle of −4.4° reduced the pitching moment by 45% of that observed in a rotor without the coning angle. The slope of the pitching moment coefficient reduction with respect to coning angle, at the constant thrust coefficient, was in close agreement with the numerical predictions. The proposed method offers a viable strategy for reducing rotor pitching moments in forward flight, thereby enhancing rotorcraft operability under windy conditions.
- 1 January 2026
- Published by Japan Society for Aeronautical and Space Sciences in TRANSACTIONS OF THE JAPAN SOCIETY FOR AERONAUTICAL AND SPACE SCIENCES
- Vol. 69 (6) , 177-185
Open AccessNegatively Coned Blades for Reducing the Pitching Moment of Small Rotors in Forward Flight
This study introduces a novel design approach that incorporates a negative coning angle for the rotor blade to reduce rotor pitching moment in forward flight for small fixed-pitch rotors. This approach modifies the lift distribution on the rotor disk to reduce the nose-up pitching moment in forward flight. The effect of the negative coning angle on the pitching moment was studied using numerical simulations and wind tunnel experiments. Computational fluid dynamics simulations conducted without a turbulence model as a preliminary analysis predicted a reduction in pitching moment when a negative coning angle was adopted. Correspondingly, wind tunnel experiments indicated that a coning angle of −4.4° reduced the pitching moment by 45% of that observed in a rotor without the coning angle. The slope of the pitching moment coefficient reduction with respect to coning angle, at the constant thrust coefficient, was in close agreement with the numerical predictions. The proposed method offers a viable strategy for reducing rotor pitching moments in forward flight, thereby enhancing rotorcraft operability under windy conditions.
- Open Access
- 27 September 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 255
Transient system-wide surrogate model for spacecraft thermal analysis using recurrent neural networks with POD data reduction
- 27 September 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 255
Open AccessTransient system-wide surrogate model for spacecraft thermal analysis using recurrent neural networks with POD data reduction
- Open Access
- 24 March 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (3) , 191-204
Impulsive force measurement by fast response pressure-sensitive paint during shock wave passage
The interaction between a shock wave and an object causes an impulsive force on the object that lasts for a very short time on the order of milliseconds. This study proposes impulsive force measurements using anodized aluminum pressure-sensitive paint (AA-PSP), which is an optical pressure measurement technique. The response time of AA-PSP is on the order of microseconds, indicating the potential for fast pressure drag measurements by integrating the pressure distribution on the surface. In this study, at first, the response time of the fabricated AA-PSP is measured and determined to be $$3.3~\upmu \hbox {s}$$ . A cylindrical model coated with the AA-PSP is installed at the outlet of a shock tube, and the surface pressure is measured in order to calculate the pressure drag with a time resolution of $$10~\upmu \hbox {s}$$ . The experimental results are compared with an Euler CFD simulation computed using an in-house code. The maximum pressure drag in the numerical result exceeds that in the experimental result; however, the maximum pressure drag timings are in good quantitative agreement. In addition to measuring the impulsive force, the AA-PSP results allow for the visualization of complex flow phenomena, such as diffraction and decay in the shock wave strength. This simultaneous measurement of the flow field and impulsive forces can deepen the understanding of the relationship between them.- 24 March 2025
- Published by Springer Nature in Shock Waves
- Vol. 35 (3) , 191-204
Open AccessImpulsive force measurement by fast response pressure-sensitive paint during shock wave passage
The interaction between a shock wave and an object causes an impulsive force on the object that lasts for a very short time on the order of milliseconds. This study proposes impulsive force measurements using anodized aluminum pressure-sensitive paint (AA-PSP), which is an optical pressure measurement technique. The response time of AA-PSP is on the order of microseconds, indicating the potential for fast pressure drag measurements by integrating the pressure distribution on the surface. In this study, at first, the response time of the fabricated AA-PSP is measured and determined to be $$3.3~\upmu \hbox {s}$$ . A cylindrical model coated with the AA-PSP is installed at the outlet of a shock tube, and the surface pressure is measured in order to calculate the pressure drag with a time resolution of $$10~\upmu \hbox {s}$$ . The experimental results are compared with an Euler CFD simulation computed using an in-house code. The maximum pressure drag in the numerical result exceeds that in the experimental result; however, the maximum pressure drag timings are in good quantitative agreement. In addition to measuring the impulsive force, the AA-PSP results allow for the visualization of complex flow phenomena, such as diffraction and decay in the shock wave strength. This simultaneous measurement of the flow field and impulsive forces can deepen the understanding of the relationship between them. - 27 January 2025
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 129 (1334) , 1077-1095
Thrust variations in small rotors due to corner and vertex effects on the ground side
Thrust changes near walls and the ground plane are influenced by the rotor’s position in indoor flight environments. This study evaluates variations in rotor thrust near a corner, which includes one wall and the ground plane, as well as a vertex, which involves two walls and the ground plane; these phenomena are referred to as the corner and vertex effects, respectively. Additionally, the rotor wake in the vertex effect was visualised using the laser sheet method, and wake velocity was measured with a hot-wire probe. The thrust change in the corner effect on the ground side was minimal, primarily depending on the ground effect. In the vertex effect, thrust decreased to 93% of the thrust outside the vertex effect when the rotor height above ground was 2.5 times the rotor radius, and the rotor was distanced from the two walls by 1.5 times the rotor radius. Flow visualisation and hot-wire velocimetry results suggest that the thrust decrease was caused by the flow recirculation structure between the fountain flow developed along the vertical corner and rotor inflow. The thrust decreases under conditions where the circulation structure appears, and fountain flow velocity accelerates the recirculation. These findings aid in planning the flight path of small multirotors in indoor flight conditions by providing guidance on distances that do not alter rotor thrust near corners and vertices.
- 27 January 2025
- Published by Cambridge University Press (CUP) in The Aeronautical Journal
- Vol. 129 (1334) , 1077-1095
Thrust variations in small rotors due to corner and vertex effects on the ground side
Thrust changes near walls and the ground plane are influenced by the rotor’s position in indoor flight environments. This study evaluates variations in rotor thrust near a corner, which includes one wall and the ground plane, as well as a vertex, which involves two walls and the ground plane; these phenomena are referred to as the corner and vertex effects, respectively. Additionally, the rotor wake in the vertex effect was visualised using the laser sheet method, and wake velocity was measured with a hot-wire probe. The thrust change in the corner effect on the ground side was minimal, primarily depending on the ground effect. In the vertex effect, thrust decreased to 93% of the thrust outside the vertex effect when the rotor height above ground was 2.5 times the rotor radius, and the rotor was distanced from the two walls by 1.5 times the rotor radius. Flow visualisation and hot-wire velocimetry results suggest that the thrust decrease was caused by the flow recirculation structure between the fountain flow developed along the vertical corner and rotor inflow. The thrust decreases under conditions where the circulation structure appears, and fountain flow velocity accelerates the recirculation. These findings aid in planning the flight path of small multirotors in indoor flight conditions by providing guidance on distances that do not alter rotor thrust near corners and vertices.
- 1 January 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 62 (1) , 3-12
Unsteady Propeller Wake Interference on Wing in Tractor Configuration at Low-Reynolds-Number Condition
This study investigates the unsteady interaction between the propeller slipstream and NACA0012 airfoil, which causes laminar separation at a moderate angle of attack and nonlinear aerodynamic characteristics at low Reynolds numbers. The Reynolds number based on chord length was set to [ ], and the propeller advance ratio was set to [ ]. Wind-tunnel experiments were conducted, including aerodynamic force measurement and time-resolved particle image velocimetry visualization. Regarding time-averaged characteristics, the propeller installed condition exhibits a linear change in lift; reduced drag; and, consequently, an improved lift-to-drag ratio. Consistent with the aerodynamic characteristics, suppressed separation and reduction in wake deficit are confirmed in the time-averaged flowfields. Additionally, vortex formation and shedding synchronized with propeller rotation are observed in unsteady flowfields at the middle and high angles of attack. This periodic and large-scale vortex structure suggests the possibility of further improving the performance of the propeller–wing system in low Reynolds numbers.
- 1 January 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Aircraft
- Vol. 62 (1) , 3-12
Unsteady Propeller Wake Interference on Wing in Tractor Configuration at Low-Reynolds-Number Condition
This study investigates the unsteady interaction between the propeller slipstream and NACA0012 airfoil, which causes laminar separation at a moderate angle of attack and nonlinear aerodynamic characteristics at low Reynolds numbers. The Reynolds number based on chord length was set to [ ], and the propeller advance ratio was set to [ ]. Wind-tunnel experiments were conducted, including aerodynamic force measurement and time-resolved particle image velocimetry visualization. Regarding time-averaged characteristics, the propeller installed condition exhibits a linear change in lift; reduced drag; and, consequently, an improved lift-to-drag ratio. Consistent with the aerodynamic characteristics, suppressed separation and reduction in wake deficit are confirmed in the time-averaged flowfields. Additionally, vortex formation and shedding synchronized with propeller rotation are observed in unsteady flowfields at the middle and high angles of attack. This periodic and large-scale vortex structure suggests the possibility of further improving the performance of the propeller–wing system in low Reynolds numbers.