Marcin Wegrzyn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marcin Wegrzyn has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Enrique Giménez
Instituto Universitario de Tecnología de Materiales, Universitat Politècnica de València (UPV), Camino de Vera s/n, 46022 Valencia, Spain
8 shared publications Adolfo Benedito
Instituto Tecnológico del Plástico (AIMPLAS) Calle Gustave Eiffel 4 46980 Paterna Spain
4 shared publicationsA. Benedito
2 shared publications- Agnieszka Iwan
Faculty of Security and Safety Research, General Tadeusz Kościuszko Military University of Land Forces, Czajkowskiego 109, 51-147 Wrocław, Poland
2 shared publications - Begoña Galindo
AIMPLAS Technological Institute of Polymers, Valencia, Spain
2 shared publications - Henryk Janeczek
Centre of Polymer and Carbon Materials, Polish Academy of Sciences, Zabrze, Poland
2 shared publications
Latest Publications
- Open Access
- 21 August 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (46)
Morphology, thermal, and electrical properties of polypropylene hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets
In this study, nanocomposites of polypropylene (PP) with various loadings of multi‐wall carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were formed by masterbatch dilution/mixing approach from individual masterbatches PP‐MWCNT and PP‐GnP. Melt mixing on a twin‐screw extruder at two different processing temperatures was followed by characterization of morphology by transmitted‐light microscopy including the statistical analysis of agglomeration behavior. The influence of processing temperature and weight fractions of both nanofillers on the dispersion quality is reported. Thermal properties of the nanocomposites investigated by DSC and TGA show sensitivity to the nanofillers weight fraction ratio and to processing conditions. Electrical conductivity is observed to increase up to an order of magnitude with the concentration of each nanofiller increasing from 0.5 wt % to 1.0 wt %. This is related with a decrease of electrical conductivity observed for unequal concentration of both nanofillers. This particular behavior shows the increase of electrical properties for higher MWCNT loadings and the increase of thermo‐mechanical properties for higher GnP loadings. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42793.
- 21 August 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (46)
Open AccessMorphology, thermal, and electrical properties of polypropylene hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets
In this study, nanocomposites of polypropylene (PP) with various loadings of multi‐wall carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were formed by masterbatch dilution/mixing approach from individual masterbatches PP‐MWCNT and PP‐GnP. Melt mixing on a twin‐screw extruder at two different processing temperatures was followed by characterization of morphology by transmitted‐light microscopy including the statistical analysis of agglomeration behavior. The influence of processing temperature and weight fractions of both nanofillers on the dispersion quality is reported. Thermal properties of the nanocomposites investigated by DSC and TGA show sensitivity to the nanofillers weight fraction ratio and to processing conditions. Electrical conductivity is observed to increase up to an order of magnitude with the concentration of each nanofiller increasing from 0.5 wt % to 1.0 wt %. This is related with a decrease of electrical conductivity observed for unequal concentration of both nanofillers. This particular behavior shows the increase of electrical properties for higher MWCNT loadings and the increase of thermo‐mechanical properties for higher GnP loadings. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42793.
- 12 June 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (37)
Thermal and electrical conductivity of melt mixed polycarbonate hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets
In this work, we present thermoplastic nanocomposites of polycarbonate (PC) matrix with hybrid nanofillers system formed by a melt‐mixing approach. Various concentrations of multi‐walled carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were mixed in to PC and the melt was homogenized. The nanocomposites were compression molded and characterized by different techniques. Torque dependence on the nanofiller composition increased with the presence of carbon nanotubes. The synergy of carbon nanotubes and GnP showed exponential increase of thermal conductivity, which was compared to logarithmic increase for nanocomposite with no MWCNT. Decrease of Shore A hardness at elevated loads present for all investigated nanocomposites was correlated with the expected low homogeneity caused by a low shear during melt‐mixing. Mathematical model was used to calculate elastic modulus from Shore A tests results. Vicat softening temperature (VST) showed opposite pattern for hybrid nanocomposites and for PC‐MWCNT increasing in the latter case. Electrical conductivity boost was explained by the collective effect of high nanofiller loads and synergy of MWCNT and GnP. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42536.
- 12 June 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (37)
Thermal and electrical conductivity of melt mixed polycarbonate hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets
In this work, we present thermoplastic nanocomposites of polycarbonate (PC) matrix with hybrid nanofillers system formed by a melt‐mixing approach. Various concentrations of multi‐walled carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were mixed in to PC and the melt was homogenized. The nanocomposites were compression molded and characterized by different techniques. Torque dependence on the nanofiller composition increased with the presence of carbon nanotubes. The synergy of carbon nanotubes and GnP showed exponential increase of thermal conductivity, which was compared to logarithmic increase for nanocomposite with no MWCNT. Decrease of Shore A hardness at elevated loads present for all investigated nanocomposites was correlated with the expected low homogeneity caused by a low shear during melt‐mixing. Mathematical model was used to calculate elastic modulus from Shore A tests results. Vicat softening temperature (VST) showed opposite pattern for hybrid nanocomposites and for PC‐MWCNT increasing in the latter case. Electrical conductivity boost was explained by the collective effect of high nanofiller loads and synergy of MWCNT and GnP. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42536.
- 12 February 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (22)
Morphology, mechanical performance, and nanoindentation behavior of injection molded PC/ABS‐MWCNT nanocomposites
In this work, nanocomposites of polycarbonate/acrylonitrile‐butadiene‐styrene (PC/ABS) with various loads of multiwall carbon nanotubes (MWCNT) are investigated. Material is previously formed by masterbatch dilution approach and further processed by injection molding at various velocities. Microscopic characterization of nanocomposites morphology reveals stronger dependence of MWCNT dispersion on processing parameters at higher nanofiller load. Dispersion of carbon nanotubes at various distances from the injection gate is studied by Raman spectroscopy showing lower deviation at elevated injection velocity. Nanoindentation results that are in agreement with uniaxial tensile testing show a slight decrease of nanocomposites' mechanical performance at 3.0 wt % MWCNT in samples injected at reduced velocity. This is explained by the increase of agglomeration behavior at these conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42014.
- 12 February 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (22)
Morphology, mechanical performance, and nanoindentation behavior of injection molded PC/ABS‐MWCNT nanocomposites
In this work, nanocomposites of polycarbonate/acrylonitrile‐butadiene‐styrene (PC/ABS) with various loads of multiwall carbon nanotubes (MWCNT) are investigated. Material is previously formed by masterbatch dilution approach and further processed by injection molding at various velocities. Microscopic characterization of nanocomposites morphology reveals stronger dependence of MWCNT dispersion on processing parameters at higher nanofiller load. Dispersion of carbon nanotubes at various distances from the injection gate is studied by Raman spectroscopy showing lower deviation at elevated injection velocity. Nanoindentation results that are in agreement with uniaxial tensile testing show a slight decrease of nanocomposites' mechanical performance at 3.0 wt % MWCNT in samples injected at reduced velocity. This is explained by the increase of agglomeration behavior at these conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42014.
- 18 December 2013
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 131 (10)
Preparation and characterization of extruded nanocomposite based on polycarbonate/butadiene‐acrylonitrile‐styrene blend filled with multiwalled carbon nanotubes
Nanocomposites of polycarbonate/acrylonitrile‐butadiene‐styrene (PC/ABS) with multiwall carbon nanotubes (MWCNT) prepared by masterbatch dilution are investigated in this work. Melt compounding with twin screw extruder is followed by complete characterization of morphology, rheological‐, mechanical‐, and thermal‐properties of the nanocomposites. Light‐transmission‐ and scanning electron microscopy shows the preferential location of MWCNT in the PC. Nevertheless, relatively good dispersion in the whole matrix is achieved, what is corroborated with the specific mechanical energy. The study of viscoelastic properties of PC/ABS‐MWCNT shows the fluid–solid transition below 0.5 wt % MWCNT. Beyond this point the continuous nanofiller network is formed in the matrix promoting the reinforcement. Addition of 0.5 wt % MWCNT reduces ductility of PC/ABS and enhances Young's modulus by about 30% and yield stress by about 20%. Moreover, theoretical values of stiffness calculated within this work agree with the experimental data. Electrical conductivity, showing percolation at 2.0 wt % MWCNT, are influenced by processing temperature. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40271.
- 18 December 2013
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 131 (10)
Preparation and characterization of extruded nanocomposite based on polycarbonate/butadiene‐acrylonitrile‐styrene blend filled with multiwalled carbon nanotubes
Nanocomposites of polycarbonate/acrylonitrile‐butadiene‐styrene (PC/ABS) with multiwall carbon nanotubes (MWCNT) prepared by masterbatch dilution are investigated in this work. Melt compounding with twin screw extruder is followed by complete characterization of morphology, rheological‐, mechanical‐, and thermal‐properties of the nanocomposites. Light‐transmission‐ and scanning electron microscopy shows the preferential location of MWCNT in the PC. Nevertheless, relatively good dispersion in the whole matrix is achieved, what is corroborated with the specific mechanical energy. The study of viscoelastic properties of PC/ABS‐MWCNT shows the fluid–solid transition below 0.5 wt % MWCNT. Beyond this point the continuous nanofiller network is formed in the matrix promoting the reinforcement. Addition of 0.5 wt % MWCNT reduces ductility of PC/ABS and enhances Young's modulus by about 30% and yield stress by about 20%. Moreover, theoretical values of stiffness calculated within this work agree with the experimental data. Electrical conductivity, showing percolation at 2.0 wt % MWCNT, are influenced by processing temperature. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014, 131, 40271.
- Open Access
- 1 November 2013
- Published by Springer Nature in Nature Communications
- Vol. 4 (1) , 2648
Nanorings and rods interconnected by self-assembly mimicking an artificial network of neurons
Molecular electronics based on structures ordered as neural networks emerges as the next evolutionary milestone in the construction of nanodevices with unprecedented applications. However, the straightforward formation of geometrically defined and interconnected nanostructures is crucial for the production of electronic circuitry nanoequivalents. Here we report on the molecularly fine-tuned self-assembly of tetrakis–Schiff base compounds into nanosized rings interconnected by unusually large nanorods providing a set of connections that mimic a biological network of neurons. The networks are produced through self-assembly resulting from the molecular conformation and noncovalent intermolecular interactions. These features can be easily generated on flat surfaces and in a polymeric matrix by casting from solution under ambient conditions. The structures can be used to guide the position of electron-transporting agents such as carbon nanotubes on a surface or in a polymer matrix to create electrically conducting networks that can find direct use in constructing nanoelectronic circuits.
- 1 November 2013
- Published by Springer Nature in Nature Communications
- Vol. 4 (1) , 2648
Open AccessNanorings and rods interconnected by self-assembly mimicking an artificial network of neurons
Molecular electronics based on structures ordered as neural networks emerges as the next evolutionary milestone in the construction of nanodevices with unprecedented applications. However, the straightforward formation of geometrically defined and interconnected nanostructures is crucial for the production of electronic circuitry nanoequivalents. Here we report on the molecularly fine-tuned self-assembly of tetrakis–Schiff base compounds into nanosized rings interconnected by unusually large nanorods providing a set of connections that mimic a biological network of neurons. The networks are produced through self-assembly resulting from the molecular conformation and noncovalent intermolecular interactions. These features can be easily generated on flat surfaces and in a polymeric matrix by casting from solution under ambient conditions. The structures can be used to guide the position of electron-transporting agents such as carbon nanotubes on a surface or in a polymer matrix to create electrically conducting networks that can find direct use in constructing nanoelectronic circuits.
- 16 May 2013
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 130 (3) , 2152-2158
The influence of injection molding parameters on electrical properties of PC/ABS‐MWCNT nanocomposites
The influence of injection molding parameters on electrical properties and morphology of PC/ABS‐MWCNT nanocomposites is presented in this article. Investigation is based on the masterbatch of 5.0 wt % carbon nanotubes obtained by melt‐mixing. Further processing includes dilution of this nanocomposite to desired concentrations on twin‐screw extruder and injection molding or direct dilution of masterbatch in injection molding. Additionally, reprocessing of materials formed by compression and injection molding is presented along with the change in electrical conductivity. Morphology differs strongly between the two processing paths showing change in agglomeration behavior between nanotubes concentrations. Electrical properties show dependence on injection velocity and melt temperature in both applied processing paths. Moreover, electrical conductivity recovery is proved after injection and compression molding. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2152–2158, 2013
- 16 May 2013
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 130 (3) , 2152-2158
The influence of injection molding parameters on electrical properties of PC/ABS‐MWCNT nanocomposites
The influence of injection molding parameters on electrical properties and morphology of PC/ABS‐MWCNT nanocomposites is presented in this article. Investigation is based on the masterbatch of 5.0 wt % carbon nanotubes obtained by melt‐mixing. Further processing includes dilution of this nanocomposite to desired concentrations on twin‐screw extruder and injection molding or direct dilution of masterbatch in injection molding. Additionally, reprocessing of materials formed by compression and injection molding is presented along with the change in electrical conductivity. Morphology differs strongly between the two processing paths showing change in agglomeration behavior between nanotubes concentrations. Electrical properties show dependence on injection velocity and melt temperature in both applied processing paths. Moreover, electrical conductivity recovery is proved after injection and compression molding. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2152–2158, 2013
- 1 January 2013
- Published by Department of Polymer Engineering, Scientific Society of Mechanical Engineering in Express Polymer Letters
- Vol. 7 (7) , 621-635
Multiwalled carbon nanotubes incorporated into a miscible blend of poly(phenylenether)/polystyrene – Processing and characterization
4 wt% multiwalled carbon nanotubes (MWCNTs) were incorporated into a miscible blend of polyphenylenether/ polystyrene (PPE/PS) on a twin-screw extruder at a screw speed of 600 rpm. The masterbatch obtained was diluted at 400 and 600 rpm to obtain lower MWCNT loadings in PPE/PS. Electron microscopy & optical microscopy images show very good MWCNT dispersion even at high filler loadings of 4!wt%, but slightly larger agglomerate size fractions are observable at higher screw speeds. While MWCNT addition enhanced the thermal stability of PPE/PS, a small change in glass transition was observed on the composites at different filler concentrations compared to PPE/PS. The specific heat capacity at glass transition decreases considerably until 2!wt% MWCNT and levels down thereafter for both processing conditions pointing to enhanced filler-matrix interaction at lower loadings. Storage modulus of the nanocomposites was enhanced significantly on MWCNT incorporation with reinforcing effect dropping considerably as a function of temperature, especially at lower filler contents. The modulus and the tensile strength of PPE/PS were only marginally enhanced in spite of excellent MWCNT dispersion in the matrix. Electrical percolation occurs at 0.4!wt% MWCNT content, and the electrical conductivity of 0.5!wt% MWCNT reinforced PPE/PS was close to 12 orders in magnitude higher compared to PPE/PS
- 1 January 2013
- Published by Department of Polymer Engineering, Scientific Society of Mechanical Engineering in Express Polymer Letters
- Vol. 7 (7) , 621-635
Multiwalled carbon nanotubes incorporated into a miscible blend of poly(phenylenether)/polystyrene – Processing and characterization
4 wt% multiwalled carbon nanotubes (MWCNTs) were incorporated into a miscible blend of polyphenylenether/ polystyrene (PPE/PS) on a twin-screw extruder at a screw speed of 600 rpm. The masterbatch obtained was diluted at 400 and 600 rpm to obtain lower MWCNT loadings in PPE/PS. Electron microscopy & optical microscopy images show very good MWCNT dispersion even at high filler loadings of 4!wt%, but slightly larger agglomerate size fractions are observable at higher screw speeds. While MWCNT addition enhanced the thermal stability of PPE/PS, a small change in glass transition was observed on the composites at different filler concentrations compared to PPE/PS. The specific heat capacity at glass transition decreases considerably until 2!wt% MWCNT and levels down thereafter for both processing conditions pointing to enhanced filler-matrix interaction at lower loadings. Storage modulus of the nanocomposites was enhanced significantly on MWCNT incorporation with reinforcing effect dropping considerably as a function of temperature, especially at lower filler contents. The modulus and the tensile strength of PPE/PS were only marginally enhanced in spite of excellent MWCNT dispersion in the matrix. Electrical percolation occurs at 0.4!wt% MWCNT content, and the electrical conductivity of 0.5!wt% MWCNT reinforced PPE/PS was close to 12 orders in magnitude higher compared to PPE/PS
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 161-165
Effect of Processing Method on Mechanical Properties of PC/ABS‐MWCNT Nanocomposites
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 161-165
Effect of Processing Method on Mechanical Properties of PC/ABS‐MWCNT Nanocomposites
- 10 December 2010
- Published by Taylor & Francis in Liquid Crystals
- Vol. 37 (12) , 1479-1492
Characterisation and mesomorphic behaviour of new aliphatic–aromatic azomethines containing ester groups
Two series of novel symmetrical azomethines prepared by the condensation of 4,4′-(butane-1,4-diylbis(oxy))bis(butane-4,1-diyl)bis(4-aminobenzoate) (PBBA470) and 5,10,15,20,25,30,35,40,45,50,55,60-dodecaoxatetrahexacontane-1,64-diylbis(4-aminobenzoate) (PBBA 1200) with a range of aldehydes have been characterised by 1H and 13C nuclear magnetic resonance, Fourier transform infrared and UV–Vis spectroscopy. Current–voltage measurements were performed using a device comprising indium–tin oxide/compound/Alq3/Al. The effect of rod length and the nature of the terminal chains on the thermal and mesomorphic behaviour of these materials were investigated by differential scanning calorimetry, polarising optical microscopy and wide- and small-angle X-ray diffraction. Additionally, the compounds were studied using various atomic force microscopy techniques, including mode and phase imaging, and measurements based on local contrast force–distance curves and roughness, together with skew and kurtosis, are presented.
- 10 December 2010
- Published by Taylor & Francis in Liquid Crystals
- Vol. 37 (12) , 1479-1492
Characterisation and mesomorphic behaviour of new aliphatic–aromatic azomethines containing ester groups
Two series of novel symmetrical azomethines prepared by the condensation of 4,4′-(butane-1,4-diylbis(oxy))bis(butane-4,1-diyl)bis(4-aminobenzoate) (PBBA470) and 5,10,15,20,25,30,35,40,45,50,55,60-dodecaoxatetrahexacontane-1,64-diylbis(4-aminobenzoate) (PBBA 1200) with a range of aldehydes have been characterised by 1H and 13C nuclear magnetic resonance, Fourier transform infrared and UV–Vis spectroscopy. Current–voltage measurements were performed using a device comprising indium–tin oxide/compound/Alq3/Al. The effect of rod length and the nature of the terminal chains on the thermal and mesomorphic behaviour of these materials were investigated by differential scanning calorimetry, polarising optical microscopy and wide- and small-angle X-ray diffraction. Additionally, the compounds were studied using various atomic force microscopy techniques, including mode and phase imaging, and measurements based on local contrast force–distance curves and roughness, together with skew and kurtosis, are presented.
- 19 November 2010
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 31 (4) , 569-576
Microstructure and piezoelectric properties of CuO added (K, Na, Li)NbO3 lead-free piezoelectric ceramics
- 19 November 2010
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 31 (4) , 569-576
Microstructure and piezoelectric properties of CuO added (K, Na, Li)NbO3 lead-free piezoelectric ceramics