Begoña Galindo
Research Subjects
Begoña Galindo has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Enrique Giménez
Instituto Universitario de Tecnología de Materiales, Universitat Politècnica de València (UPV), Camino de Vera s/n, 46022 Valencia, Spain
6 shared publications Adolfo Benedito
3 shared publications- Adolfo Benedito
Instituto Tecnológico del Plástico (AIMPLAS), 4 Gustave Eiffel, Paterna, 46980 Valencia, Spain
2 shared publications Ignacio Buezas
Instituto Tecnológico del Plástico–Asociación de Investigación de Materiales Plasticos (AIMPLAS), C/Gustave Eiffel, 4. València Parc Tenològic 46980 Paterna (Valencia), Spain
2 shared publications- Marcin Wegrzyn
Instituto Tecnológico del Plástico (AIMPLAS) Calle Gustave Eiffel 4 46980 Paterna Spain
2 shared publications A Navas
1 shared publication
Latest Publications
- 18 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 177-185
EMI Shielding Effectiveness Study for Innovative Carbon Nanotube Materials in the 5G Frequency Region
It is crucial to extend the electromagnetic compatibility (EMC) studies to the new frequency regions where modern telecommunication systems operate, specifically those related to the fifth-generation (5G) technology standard for broadband cellular networks. Electric autonomous vehicles (EAVs) are systems that feature 5G technology on board and for which it is essential to ensure the proper management of EMC to prevent malfunctions. Given the considerable development of the EAV-related sector, new materials and solutions for EMI shielding with properties that reduce interference in the frequency regions of 5G technology are being investigated. Today, meatal-based solutions are the most common EMI shielding materials used to mitigate EMC problems. Nevertheless, with the appearance of EAVs, it is needed the design of novel materials that provide a significant balance in terms of shielding effectiveness (SE) and mechanical properties. Thereby, carbon nanotubes (CNTs) are an attractive alternative to conventional EMI shielding materials due to their characteristics. The lightweight condition, flexibility, cost-effectiveness, easy processing, and resistance to corrosion made this new type of material perfect to be used in the field of EAVs. This contribution focuses on describing and characterizing three nanocomposite materials manufactured by loading a polymer matrix with 5%, 7%, and 10% CNT concentrations, respectively. The SE measurement is carried out with a coaxial sample holder based on the standard ASTM D4935-18. This measurement setup makes it possible to determine the performance of the three materials under test up to 18 GHz, covering part of the operation frequencies of 5G systems.
- 18 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 177-185
EMI Shielding Effectiveness Study for Innovative Carbon Nanotube Materials in the 5G Frequency Region
It is crucial to extend the electromagnetic compatibility (EMC) studies to the new frequency regions where modern telecommunication systems operate, specifically those related to the fifth-generation (5G) technology standard for broadband cellular networks. Electric autonomous vehicles (EAVs) are systems that feature 5G technology on board and for which it is essential to ensure the proper management of EMC to prevent malfunctions. Given the considerable development of the EAV-related sector, new materials and solutions for EMI shielding with properties that reduce interference in the frequency regions of 5G technology are being investigated. Today, meatal-based solutions are the most common EMI shielding materials used to mitigate EMC problems. Nevertheless, with the appearance of EAVs, it is needed the design of novel materials that provide a significant balance in terms of shielding effectiveness (SE) and mechanical properties. Thereby, carbon nanotubes (CNTs) are an attractive alternative to conventional EMI shielding materials due to their characteristics. The lightweight condition, flexibility, cost-effectiveness, easy processing, and resistance to corrosion made this new type of material perfect to be used in the field of EAVs. This contribution focuses on describing and characterizing three nanocomposite materials manufactured by loading a polymer matrix with 5%, 7%, and 10% CNT concentrations, respectively. The SE measurement is carried out with a coaxial sample holder based on the standard ASTM D4935-18. This measurement setup makes it possible to determine the performance of the three materials under test up to 18 GHz, covering part of the operation frequencies of 5G systems.
- 1 June 2018
- Published by Elsevier in Materials Today Communications
- Vol. 15, 105-108
Biobased conductive plastic materials for manufacturing capacitive lamps
- 1 June 2018
- Published by Elsevier in Materials Today Communications
- Vol. 15, 105-108
Biobased conductive plastic materials for manufacturing capacitive lamps
- 1 August 2016
- Published by Elsevier in Composites Part B: Engineering
- Vol. 98, 330-338
Comparative study between the microwave heating efficiency of carbon nanotubes versus multilayer graphene in polypropylene nanocomposites
- 1 August 2016
- Published by Elsevier in Composites Part B: Engineering
- Vol. 98, 330-338
Comparative study between the microwave heating efficiency of carbon nanotubes versus multilayer graphene in polypropylene nanocomposites
- 4 June 2016
- Published by Wiley in Polymer Engineering & Science
- Vol. 56 (12) , 1321-1329
Microwave heating of polymers: Influence of carbon nanotubes dispersion on the microwave susceptor effectiveness
Carbon nanotubes dispersion within the polymer matrix is a very important factor to take into account when developing new nanocomposites with optimized properties. In this article, dispersion studies have been carried out with polypropylene filled with 1% of multiwall carbon nanotubes. The nanocomposites were obtained by melt compounding in a corotative twin screw extruder. Processing parameters as screw speed, screw configuration and feeding technology were modified to analyse their effect onto carbon nanotubes dispersion. Developed nanocomposites were exposed to microwave heating (5.8 GHz, 700 W, 60 min) and heating temperature was monitored. The relation between dispersion level of carbon nanotubes and heating effectiveness was studied. Microwave heating efficiency of carbon nanotubes was increased as dispersion was improved. Electrical conductivity of nanocomposites was measured and used as indirect variable of microwave heating susceptor of carbon nanotubes nanocomposites. Higher electrical conductivity indicates a better microwave susceptor propertiy of the nanocomposite. POLYM. ENG. SCI., 56:1321–1329, 2016. © 2016 Society of Plastics Engineers
- 4 June 2016
- Published by Wiley in Polymer Engineering & Science
- Vol. 56 (12) , 1321-1329
Microwave heating of polymers: Influence of carbon nanotubes dispersion on the microwave susceptor effectiveness
Carbon nanotubes dispersion within the polymer matrix is a very important factor to take into account when developing new nanocomposites with optimized properties. In this article, dispersion studies have been carried out with polypropylene filled with 1% of multiwall carbon nanotubes. The nanocomposites were obtained by melt compounding in a corotative twin screw extruder. Processing parameters as screw speed, screw configuration and feeding technology were modified to analyse their effect onto carbon nanotubes dispersion. Developed nanocomposites were exposed to microwave heating (5.8 GHz, 700 W, 60 min) and heating temperature was monitored. The relation between dispersion level of carbon nanotubes and heating effectiveness was studied. Microwave heating efficiency of carbon nanotubes was increased as dispersion was improved. Electrical conductivity of nanocomposites was measured and used as indirect variable of microwave heating susceptor of carbon nanotubes nanocomposites. Higher electrical conductivity indicates a better microwave susceptor propertiy of the nanocomposite. POLYM. ENG. SCI., 56:1321–1329, 2016. © 2016 Society of Plastics Engineers
- Open Access
- 21 August 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (46)
Morphology, thermal, and electrical properties of polypropylene hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets
In this study, nanocomposites of polypropylene (PP) with various loadings of multi‐wall carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were formed by masterbatch dilution/mixing approach from individual masterbatches PP‐MWCNT and PP‐GnP. Melt mixing on a twin‐screw extruder at two different processing temperatures was followed by characterization of morphology by transmitted‐light microscopy including the statistical analysis of agglomeration behavior. The influence of processing temperature and weight fractions of both nanofillers on the dispersion quality is reported. Thermal properties of the nanocomposites investigated by DSC and TGA show sensitivity to the nanofillers weight fraction ratio and to processing conditions. Electrical conductivity is observed to increase up to an order of magnitude with the concentration of each nanofiller increasing from 0.5 wt % to 1.0 wt %. This is related with a decrease of electrical conductivity observed for unequal concentration of both nanofillers. This particular behavior shows the increase of electrical properties for higher MWCNT loadings and the increase of thermo‐mechanical properties for higher GnP loadings. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42793.
- 21 August 2015
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 132 (46)
Open AccessMorphology, thermal, and electrical properties of polypropylene hybrid composites co‐filled with multi‐walled carbon nanotubes and graphene nanoplatelets
In this study, nanocomposites of polypropylene (PP) with various loadings of multi‐wall carbon nanotubes (MWCNT) and graphene nanoplatelets (GnP) were formed by masterbatch dilution/mixing approach from individual masterbatches PP‐MWCNT and PP‐GnP. Melt mixing on a twin‐screw extruder at two different processing temperatures was followed by characterization of morphology by transmitted‐light microscopy including the statistical analysis of agglomeration behavior. The influence of processing temperature and weight fractions of both nanofillers on the dispersion quality is reported. Thermal properties of the nanocomposites investigated by DSC and TGA show sensitivity to the nanofillers weight fraction ratio and to processing conditions. Electrical conductivity is observed to increase up to an order of magnitude with the concentration of each nanofiller increasing from 0.5 wt % to 1.0 wt %. This is related with a decrease of electrical conductivity observed for unequal concentration of both nanofillers. This particular behavior shows the increase of electrical properties for higher MWCNT loadings and the increase of thermo‐mechanical properties for higher GnP loadings. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015, 132, 42793.
- Open Access
- 22 August 2014
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 64
Effect of the number of layers of graphene on the electrical properties of TPU polymers
- 22 August 2014
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 64
Open AccessEffect of the number of layers of graphene on the electrical properties of TPU polymers
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 161-165
Effect of Processing Method on Mechanical Properties of PC/ABS‐MWCNT Nanocomposites
- 18 December 2012
- Published by Wiley in Macromolecular Symposia
- Vol. 321-322 (1) , 161-165
Effect of Processing Method on Mechanical Properties of PC/ABS‐MWCNT Nanocomposites
- 11 August 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 122 (6) , 3744-3750
Dispersion and characterization of thermoplastic polyurethane/multiwalled carbon nanotubes by melt mixing
The dispersion of multiwalled carbon nanotubes (MWCNT) in thermoplastic polyurethanes (TPUs) was evaluated in a corotative twin‐screw extruder through a melt‐blending process. A specific experimental design was prepared with different parameters, such as screw speed, screw design, and carbon nanotube loading, taken into account. The obtained samples were characterized by thermogravimetric analysis, light transmission microscopy, field emission scanning electron microscopy, dynamic rheometry, dynamic mechanical analysis, and electrical conductivity. This work focuses on the influence of the compounding parameters in the dispersion quality of MWCNTs in a TPU matrix to optimize them for an industrial scaleup. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011
- 11 August 2011
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 122 (6) , 3744-3750
Dispersion and characterization of thermoplastic polyurethane/multiwalled carbon nanotubes by melt mixing
The dispersion of multiwalled carbon nanotubes (MWCNT) in thermoplastic polyurethanes (TPUs) was evaluated in a corotative twin‐screw extruder through a melt‐blending process. A specific experimental design was prepared with different parameters, such as screw speed, screw design, and carbon nanotube loading, taken into account. The obtained samples were characterized by thermogravimetric analysis, light transmission microscopy, field emission scanning electron microscopy, dynamic rheometry, dynamic mechanical analysis, and electrical conductivity. This work focuses on the influence of the compounding parameters in the dispersion quality of MWCNTs in a TPU matrix to optimize them for an industrial scaleup. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011