Chun-Jae Yoo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Chun-Jae Yoo has a total of 109 co-authors. Here are the top co-authors by number of shared publications:
- Jeong-Myeong Ha
Clean Energy Research Center, Korea Institute of Science and Technology (KIST), Seoul 02792, Republic of Korea
8 shared publications Jae-Wook Choi
Clean Energy Research Center, Korea Institute of Science and Technology, Seoul 02792, Republic of Korea
7 shared publications- Christopher W. Jones
Georgia Institute of Technology
6 shared publications - Jungkyu Choi
Korea University
5 shared publications Dong Jin Suh
4 shared publicationsHyunjoo Lee
4 shared publications
Latest Publications
- Open Access
- 3 November 2026
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 16 (22) , 22876-22887
Ether Coordination in Ionomers Switches Function with Length Scale in CO2 Electrolysis
CO2 electrolysis to CO relies on anion-exchange ionomers (AEIs) in two distinct roles, as the membrane and as the catalyst-layer binder, yet the design criteria for the two roles are rarely separated. Here, we demonstrate that side-chain architecture switches function with length scale by comparing AEIs bearing hexamethylene (HTMA) or ether-containing (EOTMA) trimethylammonium spacers in each role. As a membrane, EOTMA immobilizes most of its water, so 56% greater uptake produces no conductivity gain. The EOTMA membrane also admits K+, which accumulates at the cathode and lowers CO selectivity relative to HTMA. As a binder, the same ether groups improve CO2 accessibility and strengthen interfacial hydrogen bonding, promoting *COOH formation and weakening *CO binding, as shown by impedance, sorption, and spectroscopic analyses. Pairing the HTMA membrane with the EOTMA binder on commercial Ag delivers a CO partial current density of 550.3 mA cm–2 at 3.51 V and 60 °C. Role-optimized ionomer design therefore offers a general strategy for engineering electrochemical interfaces.
- 3 November 2026
- Published by American Chemical Society (ACS) in ACS Catalysis
- Vol. 16 (22) , 22876-22887
Open AccessEther Coordination in Ionomers Switches Function with Length Scale in CO2 Electrolysis
CO2 electrolysis to CO relies on anion-exchange ionomers (AEIs) in two distinct roles, as the membrane and as the catalyst-layer binder, yet the design criteria for the two roles are rarely separated. Here, we demonstrate that side-chain architecture switches function with length scale by comparing AEIs bearing hexamethylene (HTMA) or ether-containing (EOTMA) trimethylammonium spacers in each role. As a membrane, EOTMA immobilizes most of its water, so 56% greater uptake produces no conductivity gain. The EOTMA membrane also admits K+, which accumulates at the cathode and lowers CO selectivity relative to HTMA. As a binder, the same ether groups improve CO2 accessibility and strengthen interfacial hydrogen bonding, promoting *COOH formation and weakening *CO binding, as shown by impedance, sorption, and spectroscopic analyses. Pairing the HTMA membrane with the EOTMA binder on commercial Ag delivers a CO partial current density of 550.3 mA cm–2 at 3.51 V and 60 °C. Role-optimized ionomer design therefore offers a general strategy for engineering electrochemical interfaces.
- Open Access
- 29 May 2026
- Published by Wiley in ChemCatChem
- Vol. 18 (11)
Exsolved SrTiRuO x ‐Based Catalyst for Selective Hydrodeoxygenation and Hydrodecarboxylation of PET‐Glycolysis‐Derived Bis(2‐hydroxyethyl) Terephthalate
Catalytic conversion of oxygenated PET‐derived intermediates into deoxygenated chemicals provides a viable strategy for plastic waste valorization. In this study, selective hydrodeoxygenation (HDO) and hydrodecarboxylation of bis(2‐hydroxyethyl) terephthalate (BHET) were conducted using Ru‐containing perovskite‐based catalysts. Among the investigated perovskites, SrTiO 3 exhibited the highest yield of deoxygenated products. The Ru/(Ru+Ti) ratio at the B‐site and the reduction temperature for Ru exsolution were systematically adjusted to optimize surface structure and catalytic performance. The catalyst with Ru/(Ru+Ti) = 0.1 (SrTi 0.9 Ru 0.1 O y ) reduced at 550 °C achieved the highest cyclohexane selectivity (69%) and deoxygenated product yield (40 carbon%). Compared with catalysts prepared by Ru impregnation on SrTiO 3 and TiO 2 supports, the exsolved catalyst exhibited superior activity. Analysis using control catalysts indicates that the improved performance originates from the interaction between exsolved Ru species and surface oxygen vacancies. These findings demonstrate the potential of perovskite‐based catalysts for deoxygenation reactions in plastic upcycling and clarify the influence of surface structure on catalytic performance.
- 29 May 2026
- Published by Wiley in ChemCatChem
- Vol. 18 (11)
Open AccessExsolved SrTiRuO x ‐Based Catalyst for Selective Hydrodeoxygenation and Hydrodecarboxylation of PET‐Glycolysis‐Derived Bis(2‐hydroxyethyl) Terephthalate
Catalytic conversion of oxygenated PET‐derived intermediates into deoxygenated chemicals provides a viable strategy for plastic waste valorization. In this study, selective hydrodeoxygenation (HDO) and hydrodecarboxylation of bis(2‐hydroxyethyl) terephthalate (BHET) were conducted using Ru‐containing perovskite‐based catalysts. Among the investigated perovskites, SrTiO 3 exhibited the highest yield of deoxygenated products. The Ru/(Ru+Ti) ratio at the B‐site and the reduction temperature for Ru exsolution were systematically adjusted to optimize surface structure and catalytic performance. The catalyst with Ru/(Ru+Ti) = 0.1 (SrTi 0.9 Ru 0.1 O y ) reduced at 550 °C achieved the highest cyclohexane selectivity (69%) and deoxygenated product yield (40 carbon%). Compared with catalysts prepared by Ru impregnation on SrTiO 3 and TiO 2 supports, the exsolved catalyst exhibited superior activity. Analysis using control catalysts indicates that the improved performance originates from the interaction between exsolved Ru species and surface oxygen vacancies. These findings demonstrate the potential of perovskite‐based catalysts for deoxygenation reactions in plastic upcycling and clarify the influence of surface structure on catalytic performance.
- Open Access
- 21 April 2026
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 16 (9) , 3280-3287
Thermally treated polyvinyl chloride (PVC)-derived highly microporous carbon support: applications in hydrotreating catalysis
The KOH treatment of thermally degraded PVC residues produces a microporous carbon support with a BET surface area of 3273 m 2 g −1 . Ru catalysts supported on this carbon exhibit high guaiacol hydrodeoxygenation activity.
- 21 April 2026
- Published by Royal Society of Chemistry (RSC) in Catalysis Science & Technology
- Vol. 16 (9) , 3280-3287
Open AccessThermally treated polyvinyl chloride (PVC)-derived highly microporous carbon support: applications in hydrotreating catalysis
The KOH treatment of thermally degraded PVC residues produces a microporous carbon support with a BET surface area of 3273 m 2 g −1 . Ru catalysts supported on this carbon exhibit high guaiacol hydrodeoxygenation activity.
- 18 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (26) , 38131-38142
High-Voltage Lithium Batteries Enabled by Facile In Situ Fabrication of Monophasic Cellulose-Based Single-Ion Conductors
The growing demand for high-energy-density, safe, and sustainable lithium-ion batteries (LIBs) necessitates the development of innovative electrolytes. Herein, we present a facile in situ preparation strategy for fabricating a high-performance single-ion conductor (SC). This SC is based on hydroxypropyl cellulose (HPC) integrated with polyethylene glycol diacrylate cross-linker, in combination with sodium styrene sulfonate (NaSS) as a functional monomer. The introduction of NaSS is crucial, as it introduces sulfonate groups that are immobilized within the polymer network, enabling selective lithium-ion transport. This approach offers a significant advancement over conventional polyether-based gel polymer electrolytes (GPEs), which usually suffer from limited oxidative stability and require the use of separators, particularly in high-voltage battery applications. The in situ polymerization method presented here eliminates the need for a separator and offers several key advantages: rapid processability, excellent scalability, and the formation of a stable solid electrolyte interface. The result is a robust, separator-free GPE. Our HPC-based single-ion conductor (MHPC SC) exhibits a high lithium transference number of 0.89 and an ionic conductivity of 2.4 mS cm-1 at room temperature. These properties are attributed to efficient lithium-ion transport through its synergistic effect of the polyanionic conductor and HPC matrix. The mechanically robust and highly conformal polymer network effectively suppresses detrimental interfacial reactions and mitigates dendrite growth, resulting in an enhanced cycling stability. Notably, the MHPC SC enables stable operation with high-voltage cathodes up to 4.3 V, achieving 94% capacity retention over 100 cycles. These findings highlight the potential of cellulose-based GPEs as a sustainable and high-performance electrolyte that significantly enhances both the safety and performance of advanced LIBs.
- 18 June 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (26) , 38131-38142
High-Voltage Lithium Batteries Enabled by Facile In Situ Fabrication of Monophasic Cellulose-Based Single-Ion Conductors
The growing demand for high-energy-density, safe, and sustainable lithium-ion batteries (LIBs) necessitates the development of innovative electrolytes. Herein, we present a facile in situ preparation strategy for fabricating a high-performance single-ion conductor (SC). This SC is based on hydroxypropyl cellulose (HPC) integrated with polyethylene glycol diacrylate cross-linker, in combination with sodium styrene sulfonate (NaSS) as a functional monomer. The introduction of NaSS is crucial, as it introduces sulfonate groups that are immobilized within the polymer network, enabling selective lithium-ion transport. This approach offers a significant advancement over conventional polyether-based gel polymer electrolytes (GPEs), which usually suffer from limited oxidative stability and require the use of separators, particularly in high-voltage battery applications. The in situ polymerization method presented here eliminates the need for a separator and offers several key advantages: rapid processability, excellent scalability, and the formation of a stable solid electrolyte interface. The result is a robust, separator-free GPE. Our HPC-based single-ion conductor (MHPC SC) exhibits a high lithium transference number of 0.89 and an ionic conductivity of 2.4 mS cm-1 at room temperature. These properties are attributed to efficient lithium-ion transport through its synergistic effect of the polyanionic conductor and HPC matrix. The mechanically robust and highly conformal polymer network effectively suppresses detrimental interfacial reactions and mitigates dendrite growth, resulting in an enhanced cycling stability. Notably, the MHPC SC enables stable operation with high-voltage cathodes up to 4.3 V, achieving 94% capacity retention over 100 cycles. These findings highlight the potential of cellulose-based GPEs as a sustainable and high-performance electrolyte that significantly enhances both the safety and performance of advanced LIBs.
- Open Access
- 21 January 2025
- Published by American Chemical Society (ACS) in JACS Au
- Vol. 5 (2) , 811-821
Thermodynamic Hydricity of a Ruthenium CO2 Hydrogenation Catalyst Supported by a Rigid PNP Pincer
Ruthenium hydride complexes supported by pincer ligands play a crucial role in the catalytic hydrogenation of CO2 to reduced C1 chemicals such as formic acid and methanol. Toward a better understanding of their hydride transfer reactivity, knowledge of the underlying thermodynamic hydricity values is deemed critical, but relevant studies remain rare. Herein, we report the experimental thermodynamic hydricity of a new ruthenium CO2 hydrogenation catalyst (acriPNP)RuH(CO)(PPh3) (1) supported by a rigid, acridane-based PNP pincer ligand. We provide the synthesis, structure, and spectroscopic characterization of reaction intermediates involved in formate generation including the anionic dihydride (2), formate (3), five-coordinate purple species (4), and H2-bound species (5). Notably, the effective hydricity of complexes 1 and 2 in THF was determined by the H2 heterolysis method, revealing values of >52 and 32 kcal/mol, respectively. The corresponding hydricity values of 45-48 kcal/mol for related Ru dihydride complexes supported by neutral PNP pincer ligands highlight the effect of anionic complex charge in promoting stronger hydride donors. CO2 insertion into the Ru-H bond of the dihydride complex proceeds effectively under ambient conditions, suggesting that base-promoted H2 heterolysis is the rate-limiting step. Using 1 as a precatalyst, turnover frequencies in the order of 300 h-1 were obtained for formate generation. Broadly, our results provide valuable benchmark thermochemical data for the design of improved CO2 hydrogenation catalysts.
- 21 January 2025
- Published by American Chemical Society (ACS) in JACS Au
- Vol. 5 (2) , 811-821
Open AccessThermodynamic Hydricity of a Ruthenium CO2 Hydrogenation Catalyst Supported by a Rigid PNP Pincer
Ruthenium hydride complexes supported by pincer ligands play a crucial role in the catalytic hydrogenation of CO2 to reduced C1 chemicals such as formic acid and methanol. Toward a better understanding of their hydride transfer reactivity, knowledge of the underlying thermodynamic hydricity values is deemed critical, but relevant studies remain rare. Herein, we report the experimental thermodynamic hydricity of a new ruthenium CO2 hydrogenation catalyst (acriPNP)RuH(CO)(PPh3) (1) supported by a rigid, acridane-based PNP pincer ligand. We provide the synthesis, structure, and spectroscopic characterization of reaction intermediates involved in formate generation including the anionic dihydride (2), formate (3), five-coordinate purple species (4), and H2-bound species (5). Notably, the effective hydricity of complexes 1 and 2 in THF was determined by the H2 heterolysis method, revealing values of >52 and 32 kcal/mol, respectively. The corresponding hydricity values of 45-48 kcal/mol for related Ru dihydride complexes supported by neutral PNP pincer ligands highlight the effect of anionic complex charge in promoting stronger hydride donors. CO2 insertion into the Ru-H bond of the dihydride complex proceeds effectively under ambient conditions, suggesting that base-promoted H2 heterolysis is the rate-limiting step. Using 1 as a precatalyst, turnover frequencies in the order of 300 h-1 were obtained for formate generation. Broadly, our results provide valuable benchmark thermochemical data for the design of improved CO2 hydrogenation catalysts.
- Open Access
- 23 September 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 499
Effect of CeO2 morphology and Ru impregnation method on CH4 selectivity reduction in polyethylene waste conversion to liquid fuels and lubricants
- 23 September 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 499
Open AccessEffect of CeO2 morphology and Ru impregnation method on CH4 selectivity reduction in polyethylene waste conversion to liquid fuels and lubricants
- 3 January 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 481
Adsorbed oxygen atoms for improving the oxidative dehydrogenation of ethane over B-site-doped layered perovskite La2Ti2O7
- 3 January 2024
- Published by Elsevier in Chemical Engineering Journal
- Vol. 481
Adsorbed oxygen atoms for improving the oxidative dehydrogenation of ethane over B-site-doped layered perovskite La2Ti2O7
- Open Access
- 15 December 2023
- Published by Elsevier in Waste Management
- Vol. 174, 411-419
Integrating experimental and computational approaches for deep eutectic solvent-catalyzed glycolysis of post-consumer polyethylene terephthalate
- 15 December 2023
- Published by Elsevier in Waste Management
- Vol. 174, 411-419
Open AccessIntegrating experimental and computational approaches for deep eutectic solvent-catalyzed glycolysis of post-consumer polyethylene terephthalate
- Open Access
- 2 December 2023
- Published by Elsevier in Environmental Pollution
- Vol. 342, 123074
Chemical upcycling of PVC-containing plastic wastes by thermal degradation and catalysis in a chlorine-rich environment
- 2 December 2023
- Published by Elsevier in Environmental Pollution
- Vol. 342, 123074
Open AccessChemical upcycling of PVC-containing plastic wastes by thermal degradation and catalysis in a chlorine-rich environment